Data List / Active Test [07/2015 - 08/2019]
- PID/DATA MONITOR INSPECTION [MAIN BODY ECU]
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Main Body / Data List.
- Select the applicable PID from the PID table.
- Verify the PID data according to the directions on the screen.
HINT:
- The PID data screen function is used for monitoring the calculated value of input/output signals in the module. Therefore, if the monitored value of the output parts is not within the specification, it is necessary to inspect the monitored value of input parts corresponding to the applicable output part control. In addition, because the system does not display an output part malfunction as an abnormality in the monitored value, it is necessary to inspect the output parts individually.
- When detecting DTCs, PIDs related to a malfunctioning system may not display even if the module is normal. Therefore, if a PID is not displayed, it is necessary to verify the DTC, perform malfunction diagnosis of the DTC that was detected, and do repairs.
- PID/DATA MONITOR TABLE [MAIN BODY ECU]
HINT:
- The [Type] in the PID/data monitor table is indicated as follows.
- Input: Value input to module
- Conversion: Value converted into value input to module
- Calculation: Value calculated for several input values in module
- Output: Value output by module
Body Electrical > Main Body > Data List
Tester Display Measurement Item Type Range Normal Condition Inspection Item Diagnostic Note Control Signal of Answerback Hazard (Remote Engine Start) - - - - - If an accessory part is installed, it cannot be used. Control Signal of Answerback Horn (Remote Engine Start) - - - - - If an accessory part is installed, it cannot be used. Security Horn Relay - - - - - If an accessory part is installed, it cannot be used. Blower Motor Relay Displays the blower relay operation status. Output Off/On - Off: Blower relay is off (ignition is switched off)
- On: Blower relay is on (ignition is switched ON)
A1-3 - Control Status of Brake Pedal by Stop Lamp Switch Displays the stop light switch (No. 1 signal) operation status. Conversion Off/On - Off: Stop light switch (No. 1 signal) is off (brake pedal is not depressed)
- On: Stop light switch (No. 1 signal) is on (brake pedal is depressed)
E1-29 - Brake Fluid Level Switch Displays the brake fluid level status. Conversion Off (Normal)/ On (Low) - Off (Normal): Brake fluid level is between MAX and MIN
- On (Low): Brake fluid level is lower than MIN
A1-21 - Central Door Lock Switch (Lock Side) Displays the door lock control switch operation status (lock operation). Conversion Off/On - Off: Door lock control switch is not in lock
- On: Door lock control switch is in lock
E1-6 - Central Door Lock Switch (Unlock Side) Displays the door lock control switch operation status (unlock operation). Conversion Off/On - Off: Door lock control switch is not in unlock
- On: Door lock control switch is in unlock
E1-6 - Open and Close Status of All Side Door by Door Switch Displays all the doors (front door, rear door) open/ closed condition. Conversion Close/OPEN - Close: All doors are closed
- OPEN: Any door is open
E1-20/E1-4/E1-19/E1-3 - Open and Close Status of Driver's Door by Door Switch Displays the front door (LH) open/closed condition. Conversion Close/OPEN - Close: Front door (LH) is closed
- OPEN: Front door (LH) is open
E1-20 - Open and Close Status of Left Rear Door by Door Switch Displays the rear door (LH) open/closed condition. Conversion Close/OPEN - Close: Rear door (LH) is closed
- OPEN: Rear door (LH) is open
E1-3 - Open and Close Status of Passenger's Door by Door Switch Displays the front door (RH) open/closed condition. Conversion Close/OPEN - Close: Front door (RH) is closed
- OPEN: Front door (RH) is open
E1-4 - Open and Closed Status of Right Rear Door by Door Switch Displays the rear door (RH) open/closed condition. Conversion Close/OPEN - Close: Rear door (RH) is closed
- OPEN: Rear door (RH) is open
E1-19 - Control Request of Door Lock Relay to ESU Displays the door lock relay operation request (lock signal) send status. The main body ECU sends a lock signal to the power management control ECU via LIN communication. Output Off/On - Off: Lock signal is not sent
(lock operation is not operated)
- On: Lock signal is sent (lock operation is operated)
E1-13 - Control Request of Door Unlock Relay to ESU Displays the door unlock relay operation request (unlock signal) send status. The main body ECU sends an unlock signal to the power management control ECU via LIN communication. Output Off/On - Off: Unlock signal is not sent (unlock operation is not operated)
- On: Unlock signal is sent (unlock operation is performed)
E1-13 - Front Fog Relay Displays the front fog light relay operation status. Output Off/On - Off: Front fog light relay is off (fog light switch is in OFF position)
- On: Front fog light relay is on (light switch is in TNS (Parking Lights) or HEAD position and fog light switch is in F.FOG position)
A1-5 - Front Fog Switch Displays the fog light switch operation status. The main body ECU receives a fog light switch input signal via CAN communication from the engine stop and start ECU. Conversion Off/On - Off: Fog light switch OFF signal is received (fog light switch is in OFF position)
- On: Fog light switch ON signal is received (fog light switch is in F.FOG position)
E1-2/E1-18 - Fuel Sensor Input Value (Main Gauge / Hall IC Type) - - - - - Displayed on Techstream but does not function. Fuel Sensor Input Value (Sub Gauge / Hall IC Type) - - - - - Displayed on Techstream but does not function. Fuel Sensor Supply Voltage (Hall IC Type) - - - - - Displayed on Techstream but does not function. Fuel Sensor Input (Main Gauge) Displays the fuel sender gauge assembly input voltage. If the fuel tank level is low, the main body ECU input voltage increases because the fuel sender gauge assembly resistance increases. Input V Displays the fuel sender gauge assembly voltage. E1-9 - Fuel Sensor Input (Sub Gauge) - - - - - Displayed on Techstream but does not function. Fuel Sensor Supply Voltage Displays the fuel sender gauge assembly supply voltage. Input V Ignition switched ON (engine off): Approx. 4.15 V E41-1/E41-7 - Head Light Cleaner Relay - - - - - Displayed on Techstream but does not function. Control Signal of Head Light from Rain Light Sensor - - - - - Displayed on Techstream but does not function. DRL (Daytime Running Lamps) Control Request to ESU Displays the running light on request signal send status. The main body ECU sends a running light on request signal to the power management control ECU via LIN communication. Output Off/On HINT: - For the specific operation condition of the PID [H/ L_DRL], refer to the [RUNNING LIGHT SYSTEM] for new vehicle instruction.
- Off: Running light on request signal is not sent
- On: Running light on request signal is sent
E1-13 - Headlight Hi-Beam Control Request to ESU Displays the headlight HI on request signal send status. The main body ECU sends a headlight HI on request signal to the power management control ECU via LIN communication. Output % - Headlight HI on request signal is not sent (headlight high beam turns off): 0 %
- Headlight HI on request signal is sent (headlight high beam turns on): 100 %
E1-13 - Headlight Lo-Beam Control Request to ESU Displays the headlight LO on request signal send status. The main body ECU sends a headlight LO on request signal to the power management control ECU via LIN communication. Output % - Headlight LO on request signal is not sent (headlight low beam turns off): 0 %
- Headlight LO on request signal is sent (headlight low beam turns on): 100 %
E1-13 - Headlight Passing Control Request to ESU Displays the headlight LO and HI on request signal send status. The main body ECU sends a headlight LO and HI on request signal to the power management control ECU via LIN communication. Output Off/On - Off: Headlight LO and HI on request signal is not sent (no passing)
- On: Headlight LO and HI on request signal is sent (passing)
E1-13 - Headlight Switch (HI) Displays the headlight dimmer switch (HI position) operation status. The main body ECU receives a headlight dimmer switch (HI position) input signal via CAN communication from the engine stop and start ECU. Conversion Off/On - Off: Headlight dimmer switch (HI position) OFF signal is received
- On: Headlight dimmer switch (HI position) ON signal is received
E1-2/E1-18 - Headlight Switch (LOW) Displays the headlight dimmer switch (LO position) operation status. The main body ECU receives a headlight dimmer switch (LO position) input signal via CAN communication from the engine stop and start ECU. Conversion Off/On - Off: Headlight dimmer switch (LO position) off signal is received
- On: Headlight dimmer switch (LO position) on signal is received
E1-2/E1-18 - Headlight Switch (OFF) Displays the headlight dimmer switch (OFF position) operation status. The main body ECU receives a headlight dimmer switch (OFF position) input signal via CAN communication from the engine stop and start ECU. Conversion Off/On - Off: Headlight dimmer switch (OFF position) off signal is received
- On: Headlight dimmer switch (OFF position) on signal is received
E1-2/E1-18 - Headlight Switch (PASS) Displays the headlight dimmer switch (passing position) operation status. The main body ECU receives a headlight dimmer switch (passing position) input signal via CAN communication from the engine stop and start ECU. Conversion Off/On - Off: Headlight dimmer switch (passing position) off signal is received
- On: Headlight dimmer switch (passing position) on signal is received
E1-2/E1-18 - Headlight Switch (TNS) Displays the headlight dimmer switch (TNS (Parking Lights) position) operation status. The main body ECU receives a headlight dimmer switch (TNS (Parking Lights) position) input signal via CAN communication from the engine stop and start ECU. Conversion Off/On - Off: Headlight dimmer switch (TNS (Parking Lights) position) off signal is received
- On: Headlight dimmer switch (TNS (Parking Lights) position) on signal is received
E1-2/E1-18 - TNS Control Request to ESU Displays the TNS (Parking Lights) on request signal send status. The main body ECU sends a TNS (Parking Lights) on request signal to the power management control ECU via LIN communication. Output Off/Right-On/Left- On/On - Off: TNS (Parking Lights) on request signal is not sent (headlight dimmer switch is in position other than TNS (Parking Lights))
- Right-On: Parking light (RH) is forcibly operated using simulation item
- Left-On: Parking light (LH) is forcibly operated using simulation item
- On: TNS (Parking Lights) on request signal is sent (headlight dimmer switch is in TNS (Parking Lights) position)
E1-13 - Control Signal of TNS Lamp from Rain Light Sensor - - - - - Displayed on Techstream but does not function. Headlight Type Information to ESU Displays the type of headlight equipped to the vehicle. The main body ECU sends information concerning the type of headlight to the power management control ECU via LIN communication Not applicable Halogen_2Lights/ Halogen_4Lights/ Lo-HID&Hi- Hlogen_4Lights/ LED_4Lights/Bi- Xenon Not applicable E1-13 - Hazard Switch Displays the hazard warning operation status. The main body ECU receives a hazard warning switch input signal via CAN communication from the engine stop and start ECU. Conversion Off/On/Unknown - Off: Hazard warning switch off signal is received (hazard warning switch is not pressed)
- On: Hazard warning switch on signal is received (hazard warning switch is pressed)
- Unknown: Signal which hazard warning switch position is not determined is received
E1-2/E1-18 - Open and Close Status of the Hood by Hood Switch Displays the hood latch switch operation status. Conversion Close/OPEN - Close: Hood latch switch is on (hood is closed)
- OPEN: Hood latch switch is off (hood is open)
A1-12 - Horn Relay Displays the horn relay operation status. Conversion Off/On - Off: Horn relay is off (horn switch is not pressed)
- On: Horn relay is on (horn switch is pressed)
A1-16 - Ignition Status Displays the IG1 power supply input status determined in the main body ECU. Conversion IG-Off/IG-On - IG-Off: IG1 power is not input to main body ECU
- IG-On: IG1 power is input to main body ECU
A1-18 - Driver Side Key Cylinder Switch (Lock Side) Displays the front door key cylinder switch operation status (lock operation). Conversion Off/On - Off: Front door key cylinder switch is not in lock (lock operation is not performed using front door key cylinder)
- On: Front door key cylinder switch is in lock (lock operation is performed using front door key cylinder)
E1-22 - Driver Side Key Cylinder Switch (Unlock Side) Displays the front door key cylinder switch operation status (unlock operation). Conversion Off/On - Off: Front door key cylinder switch is not in unlock (unlock operation is not performed using front door key cylinder)
- On: Front door key cylinder switch is in unlock (unlock operation is performed using front door key cylinder)
E1-22 - Driver Side Door Lock Link Switch (Lock Side) Displays the front door lock-link switch operation status (lock operation). Conversion Off/On - Off: Front door lock-link switch is not in lock (lock operation is not performed using driver's door lock knob)
- On: Front door lock-link switch is in lock (lock operation is performed using driver's door lock knob)
E1-1 - Driver Side Door Lock Link Switch (Unlock Side) Displays the front door lock-link switch operation status (unlock operation). Conversion Off/On - Off: Front door lock-link switch is not in unlock (unlock operation is not performed using driver's door lock knob)
- On: Front door lock-link switch is in unlock (unlock operation is performed using driver's door lock knob)
E1-17 - Passenger / Rear Side Door Lock Link Switch (Unlock Side) Displays the door lock-link switch (passenger-side/ rear-side) operation status (lock operation). Conversion Off/On - Off: Door lock-link switch (passenger-side/rear-side) is not in lock (lock operation is not performed using door lock knob (passenger-side/ rear-side))
- On: Door lock-link switch (passenger-side/rear-side) is in lock (lock operation is performed using door lock knob (passenger-side/rear-side))
E1-7 - Control Signal of Panic Hazard (Remote Engine Start) - - - - - If an accessory part is installed, it cannot be used. Control Signal of Panic Horn (Remote Engine Start) - - - - - If an accessory part is installed, it cannot be used. PTC Heater Status - - - - - Displayed on Techstream but does not function. Rear Defogger Relay Displays the rear window defogger relay operation status. Output Off/On - Off: Rear window defogger relay is off (rear window defogger switch is not pressed)
- On: Rear window defogger relay is on (rear window defogger switch is pressed)
A1-6 - Rear Fog Lamp - - - - - Displayed on Techstream but does not function. Rear Fog Switch - - - - - Displayed on Techstream but does not function. Control Request of Reverse Lamp to ESU Displays the back-up light on request signal send status. The main body ECU sends a back-up light on request signal to the power management control ECU via LIN communication. Output Off/On - Off: Back-up light on request signal is not sent (MTX: shift lever is not in reverse position, ATX: selector lever is not in R position)
- On: Back-up light on request signal is sent (MTX: shift lever is in reverse position, ATX: selector lever is in R position)
E1-13 - Control Request of Room Lamp to ESU Displays the personal light on request signal send status. The main body ECU sends a personal light on request signal to the power management control ECU via LIN communication. Output Off/100%_On/ 60%_On/50%_On/ 40%_On/30%_On/ 20%_On HINT: - For the specific operation condition of the PID [ROOM_LAMP], refer to the [INTERIOR LIGHT CONTROL SYSTEM] for new vehicle instruction.
- Off: Personal light on request signal is not sent
- 100%_On: Personal light on request signal (100%) is sent
- 60%_On: Personal light on request signal (60%) is sent
- 50%_On:-
- 40%_On:-
- 30%_On:-
- 20%_On:-
E1-13 - Seat Belt Status (Row 2 Center) - - - - - Displayed on Techstream but does not function. Seat Belt Status (Row 2 Left Side) - - - - - Displayed on Techstream but does not function. Seat Belt Status (Row 2 Right Side) - - - - - Displayed on Techstream but does not function. Seat Belt Status (Row 3 Center) - - - - - Displayed on Techstream but does not function. Seat Belt Status (Row 3 Left Side) - - - - - Displayed on Techstream but does not function. Seat Belt Status (Row 3 Right Side) - - - - - Displayed on Techstream but does not function. Stop Lamp Control Signal from DSC Displays the brake light signal reception status. The main body ECU receives a brake light signal via CAN communication from the DSC. Conversion Unknown/Off/On/ Backup_On - Unknown: Brake light signal cannot be received
- Off: Brake light signal (turn-off) is received (SCBS brake control is not operating)
- On: Brake light signal (turn-on) is received (SCBS brake control is operating)
- Backup_On: Brake light signal (turn-on) is received (malfunction is occurring in brake headlight dimmer switch)
A1-2/A1-14 - Stop Lamp Control Displays the brake light relay operation status. Output Off/On HINT: - When the brake control (SCBS brake) is operating, the brake light relay turns on.
- Off: Brake light relay is off
(brake pedal is not depressed)
- On: Brake light relay is on (brake pedal is depressed)
E41-18 - Stop Lamp Input Displays the brake light operation status. Conversion Off/On - Off: Brake light turns off (brake pedal is not depressed)
- On: Brake light turns on (brake pedal is depressed)
E1-30 - Input Status of Trunk/Back Door Opener Switch Displays the trunk lid opener switch (exterior) operation status. Conversion Off/On - Off: Trunk lid opener switch (exterior) is off (trunk lid opener switch (exterior) is not pressed)
- On: Trunk lid opener switch (exterior) is on (trunk lid opener switch (exterior) is pressed)
E1-10 - Input Status of Trunk Opener Switch on Instrument Panel Displays the trunk lid opener switch (interior) operation status. Conversion Off/On - Off: Trunk lid opener switch (interior) is off (trunk lid opener switch (interior) is not pressed)
- On: Trunk lid opener switch (interior) is on (trunk lid opener switch (interior) is pressed)
A1-11 - Open and Close Status of Trunk/Back Door by Trunk/Back Door Latch Switch Displays the trunk lid latch switch operation status. Conversion Close/OPEN - Close: Trunk lid latch switch is off (trunk is closed)
- OPEN: Trunk lid latch switch is on (trunk is open)
E1-15 - Control Request of Trunk/Cargo Compartment Light to ESU Displays the luggage compartment room light on request signal send status. The main body ECU sends a luggage compartment room light on request signal to the power management control ECU via LIN communication. Output Off/On - Off: Trunk compartment light on request signal is not sent (trunk is closed)
- On: Trunk compartment light on request signal is sent (trunk is open)
E1-13 - Control Request of Trunk/Back Door Electric Latch Motor to ESU Displays the trunk release signal send status. The main body ECU sends a trunk release signal to the power management control ECU via LIN communication. Output Off/On - Off: Trunk release signal is not sent (trunk lid opener switch (interior) and trunk lid opener switch (exterior) is not pressed)
- On: Trunk release signal is sent (trunk lid opener switch (interior) or trunk lid opener switch (exterior) is pressed)
E1-13 - Turn Light (Left) Displays the turn light (LH) operation status. Output Off/On - Off: Turn light (LH) turns off (turn switch is in OFF position)
- On: Turn light (LH) flashes (turn switch is in LH position)
E41-4/A1-13 - Turn Light (Right) Displays the turn light (RH) operation status. Output Off/On - Off: Turn light (RH) turns off (turn switch is in OFF position)
- On: Turn light (RH) flashes (turn switch is in RH position)
E41-3/A1-1 - Turn Switch Displays the turn switch operation status. The main body ECU receives a turn switch input signal via CAN communication from the engine stop and start ECU. Conversion Off/Turn_R_On/ Turn_L_On/ Unknown - Off: Turn switch off signal is received (turn switch is in OFF position)
- Turn_R_On: Turn switch RH signal is received (turn switch is in RH position)
- Turn_L_On: Turn switch LH signal is received (turn switch is in LH position)
- Unknown: Signal which turn switch position is not determined is received
E1-2/E1-18 - Module Supply Voltage Displays the main body ECU supply voltage. Input V Switch the ignition ON (engine off):Approx. 12 V E41-1 - Module Supply Voltage (+B (HAZARD)) Displays the main body ECU supply voltage. Input V Switch the ignition ON (engine off):Approx. 12 V E41-1 - Vehicle Speed - - - - - Displayed on Techstream but does not function. Washer Control Request to ESU Displays the washer operation request signal send status. The main body ECU sends a washer operation request signal to the power management control ECU via LIN communication. Output Off/Front/Rear - Off: Washer operation request signal is not sent (washer is not operating)
- Front: Front washer operation request signal is sent (front washer switch is in ON position)
- Rear: Rear washer operation request signal is sent (rear washer switch is in rear washer position)
E1-13 - Front Washer Switch Displays the front washer switch operation status. The main body ECU receives a front washer switch input signal via CAN communication from the engine stop and start ECU. Conversion Off/On - Off: Front washer switch off signal is received (front washer switch is in OFF position)
- On: Front washer switch on signal is received (front washer switch is in ON position)
E1-2/E1-18 - Washer Fluid Level Displays the washer fluid level status. Conversion Off (Normal)/ On (Low) - Off (Normal): Washer fluid level is normal
- On (Low): Washer fluid level is low
A1-9 - Rear Washer Switch - - - - - Displayed on Techstream but does not function. Control Signal of Wiper from Rain Light Sensor - - - - - Displayed on Techstream but does not function. Front Wiper Auto Stop Switch Status Displays the autostop switch operation status (windshield wiper arm and blade position). Conversion P_Posi/Not_P_Posi - P_Posi: Windshield wipers are stopped in park position
- Not_P_Posi: Windshield wipers are stopped in position other than park
A-7 - Front Wiper INT Level Displays the sensitivity adjustment volume operation status. The main body ECU receives a sensitivity adjustment volume input signal via CAN communication from the engine stop and start ECU. Conversion % The value changes according to the sensitivity adjustment volume operation. E1-2/E1-18 - Front Wiper Relay Displays the wiper INT relay operation status. Output Off/On - Off: Wiper INT relay is off (windshield wiper are not operating)
- On: Wiper INT relay is on (windshield wipers are operating)
A1-15 - Front Wiper Relay (HI) Displays the wiper HI relay operation status. Output Off/On HINT: - If the windshield wiper switch is in the INT/ AUTO position, the wiper HI relay turns on depending on the amount of rainfall.
- Off: Wiper HI relay is off (windshield wiper switch is in position other than HI)
- On: Wiper HI relay is on (windshield wiper switch is in HI position)
A1-4 - Front Wiper Switch Displays the windshield wiper switch operation status. The main body ECU receives a windshield wiper switch input signal via CAN communication from the engine stop and start ECU. Conversion OFF/LOW/HI/INT /AUTO - Off: Windshield wiper switch off signal is received (windshield wiper switch is in OFF position)
- LOW: Windshield wiper switch LOW signal is received (windshield wiper switch is in LO position)
- HI: Windshield wiper switch HI signal is received (windshield wiper switch is in HI position)
- INT/AUTO: Windshield wiper switch INT signal or AUTO signal is received (windshield wiper switch is in INT/AUTO position)
E1-2/E1-18 - Rear Wiper Control Request to ESU - - - - - Displayed on Techstream but does not function. Rear Wiper Intermittent Time - - - - - Displayed on Techstream but does not function. Rear Wiper Switch - - - - - Displayed on Techstream but does not function. - The [Type] in the PID/data monitor table is indicated as follows.
- ACTIVE COMMAND MODES INSPECTION [MAIN BODY ECU]
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Main Body / Active Test.
- Select the simulation items from the PID table.
- Perform the active command modes function, inspect the operations for each parts.
- If the operation of output parts cannot be verified after the active command mode inspection is performed, this could indicate the possibility of an open or short circuit, sticking, or operation malfunction in the output parts.
- ACTIVE COMMAND MODES TABLE [MAIN BODY ECU]
HINT:
- Simulation items on parts which are not equipped to the vehicle do not operate.
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Inspection Item Diagnostic Note Security Horn Relay - - - If an accessory part is installed, it cannot be used. Blower Motor Relay - Off: Turns the blower relay off.
- On: Turns the blower relay on.
Off/On Blower relay Ignition switched ON
(engine off or on)Control Request of Door Lock Relay to ESU HINT: - The main body ECU sends a door lock relay operation request signal (lock signal) to the power management control ECU via LIN communication.
- Off: Does not lock the door.
- On: Locks the door.
Off/On Door lock relay Ignition switched ON
(engine off or on)Control Request of Door Unlock Relay to ESU HINT: - The main body ECU sends a door unlock relay operation request signal (unlock signal) to the power management control ECU via LIN communication.
- Off: Does not unlock the door.
- On: Unlocks the door.
Off/On Door unlock relay Ignition switched ON
(engine off or on)Front Fog Relay - Off: Turns the fog light assembly off.
- On: Turns the fog light assembly on
Off/On Fog light assembly relay Ignition switched ON
(engine off or on)Head Light Cleaner Relay - - - Displayed on Techstream but does not function. DRL (Daytime Running Lamps) Control Request to ESU HINT: - The main body ECU sends a DRL on request signal to the power management control ECU via LIN communication.
- Off: The DRLs are turned off.
- On: The DRLs are turned on.
Off/On DRL Ignition switched ON
(engine off or on)Headlight Hi-Beam Control Request to ESU HINT: - The main body ECU sends a headlight HI on request signal to the power management control ECU via LIN communication.
- 0%: The headlights HI are turned off.
- 100%: The headlights HI are turned on.
0%/100% Headlight HI Ignition switched ON
(engine off or on)Headlight Lo-Beam Control Request to ESU HINT: - The main body ECU sends a headlight LO on request signal to the power management control ECU via LIN communication.
- 0%: The headlights LO are turned off.
- 100%: The headlights LO are turned on.
0%/100% Headlight LO Ignition switched ON
(engine off or on)TNS Control Request to ESU HINT: - The main body ECU sends a TNS on request signal to the power management control ECU via LIN communication.
- Off: Turns the parking lights off.
- Right-On: Turns the parking light (RH) on.
- Left-On: Turns the parking light (LH) on.
- On: Turns the parking lights (RH/LH) on.
Off/Right- On/Left-On/ On Parking light Ignition switched ON
(engine off or on)Horn Relay - Off: Stops the horn.
- On: Sounds the horn.
Off/On Horn relay Ignition switched ON
(engine off or on)PTC Heater Status - - - Displayed on Techstream but does not function. Rear Defogger Relay - Off: Stops the rear window defogger.
- On: Operates the rear window defogger.
Off/On Rear window defogger relay Ignition switched ON
(engine off or on)Rear Fog Lamp - - - Displayed on Techstream but does not function. Control Request of Reverse Lamp to ESU HINT: - The main body ECU sends a back-up light on request signal to the power management control ECU via LIN communication.
- Off: Turns the back-up light off.
- On: Turns the back-up light on.
Off/On Back-up light Ignition switched ON
(engine off or on)Control Request of Room Lamp to ESU HINT: - The main body ECU sends a personal light on request signal to the power management control ECU via LIN communication.
- Off: Turns the personal light off.
- 100%_On: Turn the personal light on.
Off/ 100%_On Personal light Ignition switched ON
(engine off or on)Stop Lamp Control - Off: Turns the brake light off.
- On: Turns the brake light on.
Off/On Brake light relay Ignition switched ON
(engine off or on)Trunk/Cargo Compartment Light to ESU HINT: - The main body ECU sends a cargo compartment light on request signal to the power management control ECU via LIN communication.
- Off: Turns the cargo compartment light off.
- On: Turns the cargo compartment light on.
Off/On Cargo compartment light Ignition switched ON
(engine off or on)Trunk/Back Door Electric Latch Motor to ESU HINT: - The main body ECU sends a trunk lid release signal to the power management control ECU via LIN communication.
- Off: Does not open the trunk.
- On: Opens the trunk.
Off/On Trunk lid release relay Ignition switched ON
(engine off or on)Front Washer Control Request to ESU HINT: - The main body ECU sends a front washer operation request signal to the power management control ECU via LIN communication.
- Off: Stops the windshield washer motor.
- Front_ON: Operates the windshield washer motor.
Off/ Front_ON Windshield glass washer motor Ignition switched ON
(engine off or on)Rear Wiper Control Request to ESU - - - Displayed on Techstream but does not function.