LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2019 >> Yaris L, Automatic Trans >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - Diagnostic Codes (8 Of 13) >> SFI System >> DTC P050A-00: Cold Start Idle Control System Performance [07/2015 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC P050A-00: Cold Start Idle Control System Performance [07/2015 - ]: Procedure

  1. IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA (MODE 2) 
    1. Perform the Freeze Frame PID Data Access Procedure.

      Refer to ON-BOARD DIAGNOSTIC TEST [07/2015 - ]

    2. Is the DTC P050A-00 on FREEZE FRAME DATA (Mode 2)?

      Result

      Result
      Yes
      No

    Result: 

    No 

    GO TO THE TROUBLESHOOTING PROCEDURE FOR DTC ON FREEZE FRAME DATA (MODE 2). 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - 08/2018] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2018 - 08/2019] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2019 - ]

    Result: 

    Yes 

    See step  2

  2. PURPOSE: VERIFY RELATED PENDING CODE AND/OR DTC 
    1. Switch the ignition off, then ON (engine off).
    2. Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.

      Refer to ON-BOARD DIAGNOSTIC TEST [07/2015 - ]

      Powertrain > Engine > Trouble Codes 

    3. Are any other PENDING CODEs and/or DTCs present?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  12

    Result: 

    No 

    See step  3

  3. PURPOSE: VERIFICATION IF MALFUNCTION CAUSED BY THROTTLE VALVE 
    1. Connect the Techstream to the DLC3.
    2. Switch the ignition ON (engine off).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Data List / Electronic Throttle Control Actual.

      Refer to ON-BOARD DIAGNOSTIC TEST [07/2015 - ]

      Powertrain > Engine > Data List 

      Tester Display
      Electronic Throttle Control Actual
    5. While gradually depressing the accelerator pedal, verify that PID monitor Electronic Throttle Control Actual value increases.
    6. Does the monitor value change according to the amount the accelerator pedal is depressed?

      Result

      Result
      Yes
      No

    Result: 

    No 

    See step  5

    Result: 

    Yes 

    See step  4

  4. PURPOSE: INSPECT INTAKE AIR SYSTEM FOR AIR SUCTION 
    1. Inspect the following parts of the intake air system for looseness, damage, and loss.
      • Between air cleaner and throttle body
      • Between throttle body and intake manifold
    2. Is there any malfunction?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  11

    Result: 

    No 

    See step  5

  5. PURPOSE: DETERMINE INTEGRITY OF THROTTLE VALVE 
    1. Inspect the throttle valve.

      Refer to INSPECTION [07/2015 - 08/2018] Refer to INSPECTION [08/2018 - ]

    2. Perform the Electronic Control Throttle Operation Inspection.

      Refer to ON-VEHICLE INSPECTION [07/2015 - 08/2018] Refer to ON-VEHICLE INSPECTION [08/2018 - ]

    3. Is there any malfunction?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  9

    Result: 

    No 

    See step  10

  6. PURPOSE: VERIFICATION OF VEHICLE REPAIR COMPLETION 
    1. Always reconnect all disconnected connectors.
    2. Clear the DTC from the ECM memory using the Techstream.

      Refer to CLEARING DTC [07/2015 - ]

      Powertrain > Engine > Clear DTCs 

    3. Implement the repeatability verification procedure.
    4. Perform the Pending Trouble Code Access Procedure.

      Refer to ON-BOARD DIAGNOSTIC TEST [07/2015 - ]

      Powertrain > Engine > Trouble Codes 

    5. Is the PENDING CODE for this DTC present?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  8

    Result: 

    No 

    See step  7

  7. PURPOSE: VERIFY IF THERE IS ANY OTHER MALFUNCTION 
    1. Is any other DTC or pending code stored?

      Result

      Result
      Yes
      No

    Result: 

    No 

    DTC TROUBLESHOOTING COMPLETED. 

    Result: 

    Yes 

    GO TO THE APPLICABLE DTC INSPECTION. 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - 08/2018] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2018 - 08/2019] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2019 - ]
  8. REPEAT THE INSPECTION FROM STEP 4. 
    1. If the malfunction recurs, replace the ECM.

      Refer to REMOVAL [07/2015 - ]

    2. Go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  7

  9. REPLACE THE THROTTLE BODY. 
    1. Refer to REMOVAL [07/2015 - ]
    2. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  6

  10. CLEAN THE THROTTLE VALVE. 
    1. Refer to REMOVAL [07/2015 - ]
    2. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  6

  11. REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE INSPECTION RESULTS. 
    1. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  6

  12. GO TO THE APPLICABLE PENDING CODE OR DTC INSPECTION. 
    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - 08/2018] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2018 - 08/2019] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2019 - ]
    2. Go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  3

scientia non olet · About LEMON Manuals