LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2019 >> Yaris LE >> Repair and Diagnosis (Single Page) >> Engine Performance >> System >> Engine Control System - Diagnostic Codes (9 Of 13) >> SFI System >> DTC P061F-00: Internal Control Module Throttle Actuator Controller Performance [08/2018 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC P061F-00: Internal Control Module Throttle Actuator Controller Performance [08/2018 - ]: Procedure

  1. VISUALLY INSPECT ECM CONNECTOR 
    1. Perform the ECM connector Inspection.
    2. Inspect the ECM connector pin type.

      Result

      Result
      200 Pin Type
      186 Pin Type

    Result: 

    186 Pin Type 

    See step  10

    Result: 

    200 Pin Type 

    See step  2

  2. VERIFY RELATED PENDING CODE AND/OR DTC 
    1. Switch the ignition off, then ON (engine off).
    2. Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.

      Refer to ON-BOARD DIAGNOSTIC TEST [07/2015 - ]

      Powertrain > Engine > Trouble Codes 

    3. Are any other PENDING CODEs and/or DTCs present?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    GO TO THE APPLICABLE PENDING CODE OR DTC INSPECTION. 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2018 - 08/2019] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2019 - ]

    Result: 

    No 

    See step  3

  3. INSPECT ENGINE STOP AND START ECU CONNECTOR CONDITION 
    1. Switch the ignition off.
    2. Disconnect the engine stop and start ECU connector.
    3. Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
    4. Is there any malfunction?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  9

    Result: 

    No 

    See step  4

  4. INSPECT ECM CONNECTOR CONDITION 
    1. Disconnect the ECM connector.
    2. Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
    3. Is there any malfunction?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  8

    Result: 

    No 

    See step  5

  5. VERIFY DTC TROUBLESHOOTING COMPLETED 
    1. Always reconnect all disconnected connectors.
    2. Clear the DTC from the ECM memory using the Techstream.

      Refer to AFTER REPAIR PROCEDURE [07/2015 - ]

      Powertrain > Engine > Clear DTCs 

    3. Perform the KOEO or KOER self test.

      Refer to ON-DEMAND SELF-TEST/KEY-ON ENGINE RUNNING SELF-TEST [07/2015 - ]

      Powertrain > Engine > Utility 

      Tester Display
      Key-On Engine Running Self-Test

      Powertrain > Engine > Utility 

      Tester Display
      On-Demand Self-Test
    4. Is the same DTC present?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  7

    Result: 

    No 

    See step  6

  6. VERIFY AFTER REPAIR PROCEDURE 
    1. Perform the "AFTER REPAIR PROCEDURE".

      Refer to AFTER REPAIR PROCEDURE [07/2015 - ]

    2. Are any DTCs present?

      Result

      Result
      Yes
      No

    Result: 

    No 

    DTC TROUBLESHOOTING COMPLETED. 

    Result: 

    Yes 

    GO TO THE APPLICABLE DTC INSPECTION. 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2018 - 08/2019] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2019 - ]
  7. REPEAT THE INSPECTION FROM STEP 2. 
    1. If the malfunction recurs, replace the ECM.

      Refer to REMOVAL [07/2015 - ]

    2. Go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  6

  8. REPAIR OR REPLACE THE CONNECTOR AND/OR TERMINALS. 
    1. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  9. REPAIR OR REPLACE THE CONNECTOR AND/OR TERMINALS. 
    1. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  10. VERIFY RELATED PENDING CODE AND/OR DTC 
    1. Switch the ignition off, then ON (engine off).
    2. Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.

      Refer to ON-BOARD DIAGNOSTIC TEST [07/2015 - ]

      Powertrain > Engine > Trouble Codes 

    3. Are any other PENDING CODEs and/or DTCs present?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    GO TO THE APPLICABLE PENDING CODE OR DTC INSPECTION. 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2018 - 08/2019] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2019 - ]

    Result: 

    No 

    See step  11

  11. INSPECT ENGINE STOP AND START ECU CONNECTOR CONDITION 
    1. Switch the ignition off.
    2. Disconnect the engine stop and start ECU connector.
    3. Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
    4. Is there any malfunction?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  17

    Result: 

    No 

    See step  12

  12. INSPECT ECM CONNECTOR CONDITION 
    1. Disconnect the ECM connector.
    2. Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
    3. Is there any malfunction?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  16

    Result: 

    No 

    See step  13

  13. VERIFY DTC TROUBLESHOOTING COMPLETED 
    1. Always reconnect all disconnected connectors.
    2. Clear the DTC from the ECM memory using the Techstream.

      Refer to AFTER REPAIR PROCEDURE [07/2015 - ]

      Powertrain > Engine > Clear DTCs 

    3. Perform the KOEO or KOER self test.

      Refer to ON-DEMAND SELF-TEST/KEY-ON ENGINE RUNNING SELF-TEST [07/2015 - ]

      Powertrain > Engine > Utility 

      Tester Display
      Key-On Engine Running Self-Test

      Powertrain > Engine > Utility 

      Tester Display
      On-Demand Self-Test
    4. Is the same DTC present?

      Result

      Result
      Yes
      No

    Result: 

    Yes 

    See step  15

    Result: 

    No 

    See step  14

  14. VERIFY AFTER REPAIR PROCEDURE 
    1. Perform the "AFTER REPAIR PROCEDURE".

      Refer to AFTER REPAIR PROCEDURE [07/2015 - ]

    2. Are any DTCs present?

      Result

      Result
      Yes
      No

    Result: 

    No 

    DTC TROUBLESHOOTING COMPLETED. 

    Result: 

    Yes 

    GO TO THE APPLICABLE DTC INSPECTION. 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2018 - 08/2019] Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2019 - ]
  15. REPEAT THE INSPECTION FROM STEP 10. 
    1. If the malfunction recurs, replace the ECM.

      Refer to REMOVAL [07/2015 - ]

    2. Go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  14

  16. REPAIR OR REPLACE THE CONNECTOR AND/OR TERMINALS. 
    1. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  13

  17. REPAIR OR REPLACE THE CONNECTOR AND/OR TERMINALS. 
    1. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  13

scientia non olet · About LEMON Manuals