Freeze Frame Data [11/2015 - 12/2018]
- FREEZE FRAME DATA
- Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.
- CHECK FREEZE FRAME DATA
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the blind spot monitor system on.
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.
- According to the display on the Techstream, display the Freeze Frame Data for the selected DTC.
Body Electrical > Blind Spot Monitor Master
Tester Display Measurement Item Range Normal Condition Diagnostic Note Main Switch State of the Blind spot monitor system OFF or ON OFF: Blind spot monitor system off
ON: Blind spot monitor system on- Warning Indicator Turning on (Master) State of the outer rear view mirror indicator LH turning on OFF or ON OFF: Any state except "ON" state
ON: Either of the following states- During initial check
- Blind spot monitor system on, vehicle detected on left hand side and turn signal switch not operated
- Warning Indicator Flashing (Master) State of the outer rear view mirror indicator LH flashing OFF or ON OFF: Any state except "ON" state
ON: Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on- Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V- Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA- Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left side of turn signal switch on
Right ON: Right side of turn signal switch on
OFF: Turn signal switch off- Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift state other than reverse (R) selected
ON: Reverse (R) selected- Vehicle Speed Vehicle speed signal -328 to 328 km/h (-204 to 204 mph) Vehicle stopped: 0 km/h (0 mph) - Steering Angle Steering angle sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases- Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Power switch on (IG): 11 to 14 V - Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed- Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0- Body Electrical > Blind Spot Monitor Slave
Tester Display Measurement Item Range Normal Condition Diagnostic Note Warning Indicator Turning on (Slave) State of the outer rear view mirror indicator RH turning on OFF or ON OFF: Any state except "ON" state
ON: Either of the following states- During initial check
- Blind spot monitor system on, vehicle detected on right hand side and turn signal switch not operated
- Warning Indicator Flashing (Slave) State of the outer rear view mirror indicator RH flashing OFF or ON OFF: Any state except "ON" state
ON: Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on- Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) OFF or ON OFF: Buzzer not sounding
ON: Buzzer sounding- Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V- Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA- Buzzer Input Circuit Voltage RCTA buzzer (blind spot monitor buzzer) voltage Min.: 0 V, Max.: 25.5 V Buzzer not sounding: 11 to 14 V
Buzzer sounding: Alternating between 0 to 14 V- Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left side of turn signal switch on
Right ON: Right side of turn signal switch on
OFF: Turn signal switch off- Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift state other than reverse (R) selected
ON: Reverse (R) selected- Vehicle Speed Vehicle speed signal -328 to 328 km/h (-204 to 204 mph) Vehicle stopped: 0 km/h (0 mph) - Steering Angle Steering angle sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases- Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Power switch on (IG): 11 to 14 V - Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed- Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0-
- CLEAR FREEZE FRAME DATA NOTE:
Clearing the DTCs will also clear the Freeze Frame Data.
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the blind spot monitor system on.
- Turn the Techstream on.
- Clear the DTCs and Freeze Frame Data.