Installation [11/2015 - ]: Procedure

INSTALL STEERING COLUMN ASSEMBLY

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the steering column assembly with the bolt and 2 nuts.

Torque: 36 N.m (367 kgf.cm, 27 ft./lbf)

Engage the clamp.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Matchmark
	Install in this direction

Install the No. 2 steering intermediate shaft assembly to the steering column assembly.
Install the bolt.
Torque: 64 N.m (653 kgf.cm, 47 ft./lbf)

CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Matchmark
	Connect in this direction

Connect the No. 2 steering intermediate shaft assembly to the steering gear assembly.
Install the bolt.
Torque: 64 N.m (653 kgf.cm, 47 ft./lbf)

INSTALL COLUMN HOLE COVER SILENCER SHEET

Engage the 2 claws to install the column hole cover silencer sheet.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Engage the claw to close the column hole cover silencer sheet.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL NO. 1 AIR DUCT

Engage the 3 claws to install a new No. 1 air duct.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL FRONT NO. 1 CONSOLE BOX INSERT
Refer to PROCEDURE - Step 17 [11/2015 - 11/2017] , or refer to PROCEDURE - Step 18 [11/2017 - 12/2018] , or refer to PROCEDURE - Step 18 [12/2018 - 07/2020] , or refer to PROCEDURE - Step 18 [07/2020 - 06/2021] , or refer to PROCEDURE - Step 17 [06/2021 - ]
INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 8 [11/2015 - 11/2017] , or refer to PROCEDURE - Step 8 [11/2017 - 08/2019] , or refer to PROCEDURE - Step 8 [08/2019 - ]
INSTALL REAR CONSOLE BOX ASSEMBLY
Refer to INSTALLATION [11/2015 - 12/2018] , or refer to INSTALLATION [12/2018 - ]
INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
Refer to INSTALLATION [11/2015 - ]

INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTE:

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed with the auxiliary battery connected and the power switch on (IG).
Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.

INSTALL UPPER STEERING COLUMN COVER

Engage the 2 claws and 4 clips to connect the upper steering column cover.

Engage the claw to install the upper steering column cover.

INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

NOTE:

If the lower steering column cover sub-assembly is installed in the incorrect order, the parts may break.

Engage the 3 claws as shown in the illustration.

Install in this Direction

Engage the 2 claws.

Install the 2 screws.

Torque: 2.0 N.m (20 kgf.cm, 18 in./lbf)

ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Refer to PROCEDURE - Step 7 [11/2015 - 12/2018] , or refer to PROCEDURE - Step 7 [12/2018 - ]
INSTALL STEERING WHEEL ASSEMBLY
See step 7, or see step 8
CHECK STEERING WHEEL CENTER POINT
INSTALL HORN BUTTON ASSEMBLY
Refer to INSTALLATION [11/2015 - ]
TORQUE SENSOR ZERO POINT CALIBRATION
Refer to CALIBRATION [11/2015 - ]