Rear Door RH Entry Lock Function does not Operate [11/2018 - ]: Procedure

1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

   Refer to OPERATION CHECK [11/2018 - 10/2023] , or refer to OPERATION CHECK [10/2023 - 11/2024] , or refer to OPERATION CHECK [11/2024 - ]

   OK

   Door locks operate normally.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO POWER DOOR LOCK CONTROL SYSTEM 

Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - 10/2023] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2023 - 11/2024] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2024 - ]

Result: 

OK 

See step  2

1. Turn the engine switch off.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Lock Sensor

2. Turn the engine switch on (IG).
3. Open and close the rear door RH.
4. Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door RH.
5. Enter the following menus: Body Electrical / Smart Key / Data List.
6. Read the Data List according to the display on the Techstream.
7. Touch the lock sensor of the rear door outside handle assembly RH.

   HINT: 

   • If the door does not lock even when touching the lock sensor, touch it with your palm.
   • When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

   Body Electrical > Smart Key > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Pr-Door Trigger Switch	Rear door RH touch sensor (lock sensor)	ON or OFF	ON: Rear door RH touch sensor (lock sensor) touched OFF: Rear door RH touch sensor (lock sensor) not touched	Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.

   Body Electrical > Smart Key > Data List 

   Tester Display
   Pr-Door Trigger Switch

   HINT: 

   When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function. Other door lock operations, such as a wireless door lock operation, can be performed consecutively.

   OK

   The Techstream display changes correctly in response to the operation of the rear door outside handle assembly RH.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result: 

NG 

See step  3

1. Disconnect the M7 certification ECU (smart key ECU assembly) connector.
2. Disconnect the K6 rear door outside handle assembly RH connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   M7-9 (CLG4) - K6-6 (ANT1)	Always	Below 1 Ω
   M7-8 (CG4B) - K6-4 (ANT2)	Always	Below 1 Ω
   M7-9 (CLG4) or K6-6 (ANT1) - Other terminals and body ground	Always	10 kΩ or higher
   M7-8 (CG4B) or K6-4 (ANT2) - Other terminals and body ground	Always	10 kΩ or higher

4. Reconnect the K6 rear door outside handle assembly RH connector.
5. Reconnect the M7 certification ECU (smart key ECU assembly) connector.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  4

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using an oscilloscope, check the waveform.

   OK

   Tester Connection	Condition	Tool Setting	Specified Condition
   M7-9 (CLG4) - G54-18 (E)	Procedure: Engine switch off Electrical key transmitter sub-assembly brought outside vehicle All doors closed All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) Rear door RH lock sensor touched	5 V/DIV., 40 ms/DIV.	Pulse generation (See waveform 1)

   *: For details about the entry function detection area, refer to Operation Check.

   Refer to OPERATION CHECK [11/2018 - 10/2023] , or refer to OPERATION CHECK [10/2023 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result: 

NG 

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY RH 

Refer to DISASSEMBLY [11/2018 - 02/2019] , or refer to DISASSEMBLY [02/2019 - 10/2019] , or refer to DISASSEMBLY [10/2019 - 08/2020] , or refer to DISASSEMBLY [08/2020 - 12/2021] , or refer to DISASSEMBLY [12/2021 - 10/2022] , or refer to DISASSEMBLY [10/2022 - 10/2023] , or refer to DISASSEMBLY [10/2023 - ]