Freeze Frame Data [11/2018 - ]
WARNING: This page is about a different variant/trim than selected.
- FREEZE FRAME DATA
- When a DTC is stored, the 4WD ECU assembly stores the current vehicle state as Freeze Frame Data.
HINT:
Freeze Frame Data at the time a DTC is stored:
- When the 4WD ECU assembly stores data at the time a DTC is stored, no updates will be performed until the data is cleared.
- "Number of IG ON" is not stored as Freeze Frame Data.
- When a DTC is stored, the 4WD ECU assembly stores the current vehicle state as Freeze Frame Data.
- CHECK FREEZE FRAME DATA
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Chassis / Four Wheel Drive / Trouble Codes.
Chassis > Four Wheel Drive > Trouble Codes
- According to the display on the Techstream, select the trouble code data display with Freeze Frame Data.
Chassis > Four Wheel Drive
Tester Display Measurement Item Range Normal Condition Diagnostic Note Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215- - Total Distance Traveled - Unit Total Distance Traveled unit km / mile - - FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)Vehicle stopped: 0 km/h (0 mph) No large fluctuations when driving at a constant speed. FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)Vehicle stopped: 0 km/h (0 mph) No large fluctuations when driving at a constant speed. RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)Vehicle stopped: 0 km/h (0 mph) No large fluctuations when driving at a constant speed. RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)Vehicle stopped: 0 km/h (0 mph) No large fluctuations when driving at a constant speed. Stop Light Switch Stop light switch OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed- OMS Switch Normal Multi-terrain select switch (integration control and panel assembly) is in NORMAL mode OFF / ON OFF: Mode other than NORMAL
ON: NORMAL mode- OMS Switch Mud & Sand Multi-terrain select switch (integration control and panel assembly) is in MUD & SAND mode OFF / ON OFF: Mode other than MUD & SAND
ON: MUD & SAND mode- OMS Switch Rock & Dirt Multi-terrain select switch (integration control and panel assembly) is in ROCK & DIRT mode OFF / ON OFF: Mode other than ROCK & DIRT
ON: ROCK & DIRT mode- Parking Brake Parking brake OFF / ON OFF: Parking brake released
ON: Parking brake applied- Lateral G Lateral G Min.: -25.10 m/s2
Max.: 24.90 m/s2- Changes in proportion with the pedal movement speed when the brake pedal is being operated. Forward and Rearward G Forward and rearward G Min.: -25.10 m/s2
Max.: 24.90 m/s2- Changes in proportion with acceleration during acceleration/deceleration. Yaw Rate Value Yaw rate value Min.: -128°/s
Max.: 127°/sVehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s- Accelerator Position Accelerator pedal depression amount Min.: 0.0%
Max.: 127.5%When the accelerator pedal is released: 0% Changes in proportion to the movement of the pedal during accelerator pedal operation. Real Engine Torque Real engine torque Min.: -1024.00 Nm
Max.: 1023.96 Nm- - Steering Angle Value Steering sensor Min.: - 3276.8°
Max.: 3276.7°Left turn: Increase
Right turn: Decrease- Vehicle Speed Vehicle speed Min.: 0.0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations IG1 Voltage Value IG1 voltage value Min.: 0.00 V
Max.: 20.40 VIgnition switch ON: 11 to 14 V - Front Axle Coupling Clutch Current Front Axle Coupling Clutch Current Min.: 0.000 A
Max.: 6.000 A- - Rear Axle Coupling Clutch Current Rear Axle Coupling Clutch Current Min.: 0.000 A
Max.: 6.000 A- - Left Coupling Current Left Coupling Current Min.: 0.000 A
Max.: 3.000 A- - Right Coupling Current Right Coupling Current Min.: 0.000 A
Max.: 3.000 A- - Front Axle Coupling Clutch Position Sensor Status Front Axle Coupling Clutch Position Sensor Status Disconnect / Connect - - Rear Axle Coupling Clutch Position Sensor Status Rear Axle Coupling Clutch Position Sensor Status Disconnect / Connect - - Propeller Shaft Revolution Propeller Shaft Revolution Min.: 0.0 rpm
Max.: 12799.8 rpm- - Front D-module Switching Status Front 4WD linear solenoid (transfer assembly) switching status Inactive / During Disconnect Transition / Disconnect / During Connect Transition / Connect - - Rear D-module Switching Status Rear 4WD linear solenoid (rear differential carrier assembly) switching status Inactive / During Disconnect Transition / Disconnect / During Connect Transition / Connect - - Oil Temperature Sensor Rear differential oil temperature Min.: -256.00°C (-428.80°F)
Min.: 255.99°C (492.78°F)- - Position Sensor Front AD Value Position Sensor Front AD Value Min.: 0.00 V
Max.: 4.98 V- - Position Sensor Rear AD Value Position Sensor Rear AD Value Min.: 0.00 V
Max.: 4.98 V- - R/L Measurement Mode (Cold FTP) R/L Measurement Mode (Cold FTP) Normal / ON - - R/L Measurement Mode R/L Measurement Mode Normal / ON - - 4WD Chassis Dynamometer Mode 4WD Chassis Dynamometer Mode Normal / ON - - 2WD Chassis Dynamometer Mode 2WD Chassis Dynamometer Mode Normal / ON - - Front Axle Coupling Clutch Request Current Front Axle Coupling Clutch Request Current Min.: 0.000 A
Max.: 6.000 A- - Rear Axle Coupling Clutch Request Current Rear Axle Coupling Clutch Request Current Min.: 0.000 A
Max.: 6.000 A- - Left Coupling Request Current Left Coupling Request Current Min.: 0.000 A
Max.: 3.000 A- - Right Coupling Request Current Right Coupling Request Current Min.: 0.000 A
Max.: 3.000 A- -
- CLEAR FREEZE FRAME DATA NOTE:
Clearing the DTCs will also clear the Freeze Frame Data.
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Clear the DTCs and Freeze Frame Data.
Refer to DTC CHECK / CLEAR [11/2018 - ]