LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2020 >> Sequoia TRD Pro >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Anti-Theft Systems >> Smart Key System (Keyless Entry) - Diagnostics - Introduction >> SMART KEY SYSTEM (for Entry Function) >> Data List / Active Test [08/2019 - ] >> Data List / Active Test [08/2019 - ]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test [08/2019 - ]

NOTE:
  • In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
  • When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  1. DATA LIST 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Smart Key / Data List.
    5. Read the Data List according to the display on the Techstream.
      BODY ELECTRICAL > SMART KEY > DATA LIST

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      D-Door Touch Sensor Driver door touch sensor (unlock sensor)* OFF or ON OFF: Driver door touch sensor (unlock sensor) not touched
      ON: Driver door touch sensor (unlock sensor) touched
      • Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
      • Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.
      P-Door Touch Sensor Front passenger door touch sensor (unlock sensor)* OFF or ON OFF: Front passenger door touch sensor (unlock sensor) not touched
      ON: Front passenger door touch sensor (unlock sensor) touched
      • Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
      • Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.
      D-Door Trigger Switch Driver door touch sensor (lock sensor)* OFF or ON OFF: Driver door touch sensor (lock sensor) not touched
      ON: Driver door touch sensor (lock sensor) touched
      • Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
      • Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
      P-Door Trigger Switch Front passenger door touch sensor (lock sensor)* OFF or ON OFF: Front passenger door touch sensor (lock sensor) not touched
      ON: Front passenger door touch sensor (lock sensor) touched
      • Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
      • Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
      Tr/B-Door Lock SW Tail gate control switch assembly (lock switch) ON or OFF ON: Tail gate control switch assembly (lock switch) pressed
      OFF: Tail gate control switch assembly (lock switch) not pressed
      • Displays whether the tail gate control switch assembly (lock switch) is on or off.
      • Use this Data List item to help determine if there is a switch malfunction when the entry back door lock function does not operate.
      Tr/B-Door Unlock SW Back door outside handle OFF or ON OFF: Back door outside handle not pushed
      ON: Back door outside handle pushed
      • Displays whether the back door outside handle is on or off.
      • Use this Data List item to help determine if there is a switch malfunction when the entry back door unlock function does not operate.
      Unmatched Vehicle-ID Key No. (incorrect or correct) No or Yes No: Communication normal
      Yes: Communication malfunction      		 The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle-ID" in the Data List).
      Other potential causes:
      • An electrical key transmitter sub-assembly from a different vehicle is being used.
      • A communication error due to wave interference.
      • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
      No Response Communication response No or Yes No: Communication normal
      Yes: Communication malfunction      		 The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the engine switch is pressed, etc., "Yes" is displayed for "No Response" in the Data List. If there is wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "No Response" in the Data List.)
      Other potential causes:
      • An electrical key transmitter sub-assembly from a different vehicle is being used.
      • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
      Unmatch Code or Form Code format (incorrect or correct) No or Yes No: Communication normal
      Yes: Communication malfunction      		 There is an error in the data sent from the electrical key transmitter sub-assembly (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
      Other potential causes:
      • An electrical key transmitter sub-assembly from a different manufacturer is being used.
      • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
      Key Low Battery Transmitter battery depleted No or Yes No: Transmitter battery not depleted
      Yes: Transmitter battery depleted      		 The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.
      HINT: 
      This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
      "Yes" can be displayed only when the Data List item "No Response" is "No".
      Power Save Cnt 10 Min. Number of times power saving control is activated due to electrical key transmitter sub-assembly being in detection area for 10 minutes or more 0 to 255 Within range of 0 to 255 If the electrical key transmitter sub-assembly is in a vehicle exterior detection area, communication is frequently performed between the vehicle and electrical key transmitter sub-assembly, resulting in an increase in transmitter battery power consumption. To prevent the transmitter battery from becoming fully depleted, if the electrical key transmitter sub-assembly is left in the detection area for 10 minutes or more, the smart key system automatically deactivates the exterior detection area the electrical key transmitter sub-assembly is in. If the doors are locked/unlocked with a wireless operation or by the mechanical key, the system resumes operation.
      Power Save Cnt 5 Days Number of times power saving control 1 (vehicle exterior periodic signal transmission stop) is activated due to engine not being started for 5 days or more 0 to 255 Within range of 0 to 255 -
      Power Save Cnt 14 Days Number of times power saving control 2 (lock/unlock sensor of front door outside handle assembly of front passenger door disabled) is activated due to engine not being started for 14 days or more 0 to 255 Within range of 0 to 255 -
      # Codes Number of trouble codes 0 to 255 Number of stored DTCs displayed -
      ID Code Difference(Resp) ID code (incorrect or correct) No or Yes No: Communication normal
      Yes: Communication malfunction      		 The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
      Other potential causes:
      • An electrical key transmitter sub-assembly from a different vehicle is being used.
      • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
      C Code Difference Challenge code (incorrect or correct) No or Yes No: Communication normal
      Yes: Communication malfunction      		 The electrical key transmitter sub-assembly sends a response code in response to the challenge code from the vehicle, but the response code is incorrect (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
      Other potential causes:
      • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
      ID Code Difference Wireless ID code (incorrect or correct) No or Yes No: Communication normal
      Yes: Communication malfunction      		 The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different. (If a wireless ID other than those for any of the registered electrical key transmitter sub-assemblies is detected, "Yes" is displayed for "ID Code Difference" in the Data List. If a wireless signal from the electrical key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for "ID Code Difference(Resp)" in the Data List.)
      Other potential causes:
      • An electrical key transmitter sub-assembly from a different vehicle is being used.
      • A communication error due to external noise (RF).
      • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
      Different Rolling Code Rolling code (incorrect or correct) No or Yes No: Communication normal
      Yes: Communication malfunction      		 The rolling code registered in the vehicle and the rolling code registered in the electrical key transmitter sub-assembly are different
      Other potential causes:
      • An electrical key transmitter sub-assembly switch is pressed 100 times or more in a location where the radio waves cannot reach the vehicle.
      • A communication error due to external noise (RF).
      • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
      B Code Difference B code mismatch No or Yes No: Communication normal
      Yes: Communication malfunction      		 -
      B Code B code registration status No Regd or Regd No Regd: B code not registered correctly
      Regd: B code registered correctly      		 -
      B Code Registration Status B code registration status OK or NG OK: B code is registered properly
      NG: B code is not registered properly      		 -
      Door Unlock Mode2 Door unlock mode All or Driver Customize setting displayed -
      Ignition Available Area Ignition available area Front or All Customize setting displayed -
      Parking Wait Time Parking wait time 0.5s, 1.5s, 2.5s or 5s Customize setting displayed -
      B-Dr Opening Operation Back door opening operation Long, Twice or OFF Customize setting displayed -
      Touch Activation Over Threshold Consecutive entry lock operation Active or Not Active Customize setting displayed -
      Wireless Signal Encryption Support Wireless signal encryption support No or Yes No: Wireless signal encryption not supported
      Yes: Wireless signal encryption supported      		 -
      Key Low Battery Warning Key Low Battery Warning OFF or ON Customize setting displayed -
      Key Left in Vehicle Buz Key left in vehicle buzzer OFF or ON Customize setting displayed -
      Engine Start Indicator Entry warning light lights OFF or ON Customize setting displayed -
      Number of Registered Key Codes Number of registered electrical key transmitter sub-assemblies 0 to 8 Number of registered electrical key transmitter sub-assemblies Up to 7 electrical key transmitter sub-assemblies can be registered.
      Short in Fr P Side Door Oscillators Circuit (Hist) Short in front passenger door electrical key antenna circuit (history) OK or NG(Hist) OK: Front passenger door electrical key antenna circuit was normal
      NG(Hist): Front passenger door electrical key antenna circuit was abnormal      		 -
      Short in D Side Door Oscillators Circuit (Hist) Short in driver door electrical key antenna circuit (history) OK or NG(Hist) OK: Driver door electrical key antenna circuit was normal
      NG(Hist): Driver door electrical key antenna circuit was abnormal      		 -
      Short in Front P Side Door Oscillators Circuit Short in front passenger door electrical key antenna circuit OK or NG OK: Front passenger door electrical key antenna circuit is normal
      NG: Front passenger door electrical key antenna circuit is abnormal      		 -
      Short in Driver Side Door Oscillators Circuit Short in driver door electrical key antenna circuit OK or NG OK: Driver door electrical key antenna circuit is normal
      NG: Driver door electrical key antenna circuit is abnormal      		 -
      1. *: Data from an actual vehicle provided for reference.
      GTY322902Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      • *1: With engine switch off, all doors closed, electrical key transmitter sub-assembly not inside vehicle and all doors locked, the unlock sensor of the front door outside handle assembly is touched.
      • *2: Approximately 150 ms
      • *3: With engine switch off, all doors closed, electrical key transmitter sub-assembly not inside vehicle and all doors unlocked, the lock sensor of the front door outside handle assembly is touched.
    6. Enter the following menus: Body Electrical / Main Body / Data List.
    7. Read the Data List according to the display on the Techstream.
      BODY ELECTRICAL > MAIN BODY > DATA LIST

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ACC SW Engine switch status OFF or ON OFF: Engine switch off
      ON: Engine switch on (ACC)      		 "ON" is also displayed when the engine switch is on (IG).
      IG SW Engine switch status OFF or ON OFF: Engine switch off
      ON: Engine switch on (IG)      		 "OFF" is also displayed when the engine switch is on (ACC).
      RR Door Courtesy SW Rear door RH courtesy light switch OFF or ON OFF: Rear door RH closed
      ON: Rear door RH open      		 -
      RL Door Courtesy SW Rear door LH courtesy light switch OFF or ON OFF: Rear door LH closed
      ON: Rear door LH open      		 -
      FR Door Lock Pos Front door RH unlock detection switch signal UNLOCK or LOCK UNLOCK: Front door RH unlocked
      LOCK: Front door RH locked      		 -
      FR Door Courtesy SW Front door RH courtesy light switch signal OFF or ON OFF: Front door RH closed
      ON: Front door RH open      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal UNLOCK or LOCK UNLOCK: Front door LH unlocked
      LOCK: Front door LH locked      		 -
      FL Door Courtesy SW Front door LH courtesy light switch signal OFF or ON OFF: Front door LH closed
      ON: Front door LH open      		 -
      RR-Door Lock Pos SW Rear door RH unlock detection switch signal OFF or ON OFF: Rear door RH locked
      ON: Rear door RH unlocked      		 -
      RL-Door Lock Pos SW Rear door LH unlock detection switch signal OFF or ON OFF: Rear door LH locked
      ON: Rear door LH unlocked      		 -
      Wireless Buzzer Resp Wireless buzzer answer-back of entry function OFF or ON Customization status displayed -
    8. Enter the following menus: Body Electrical / Power Source Control / Data List.
    9. Read the Data List according to the display on the Techstream.
      BODY ELECTRICAL > POWER SOURCE CONTROL > DATA LIST

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ACC Relay Monitor ACC relay activation OFF or ON OFF: Engine switch off
      ON: Engine switch on (ACC)      		 When the engine switch is on (IG), ON is displayed.
      Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Engine switch off
      ACC ON: Engine switch on (ACC)
      IG ON: Engine switch on (IG)
      ST ON: Sending engine start request signal      		 -
      IG Relay Monitor (Outside) IG relay coil voltage monitor status OFF or ON OFF: Engine switch off
      ON: Engine switch on (IG)
      • Use this item to determine if the IG relay is malfunctioning.
      • When the engine switch is on (ACC), OFF is displayed.
    10. Enter the following menus: Body Electrical / Back Door P/W / Data List.
    11. Read the Data List according to the display on the Techstream.
      BODY ELECTRICAL / BACK DOOR P/W / DATA LIST

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Back Door Courtesy Switch Back door courtesy switch signal ON or OFF OFF: Back door closed
      ON: Back door open      		 -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Smart Key / Active Test.
    5. Perform Active Test according to the display on the Techstream.
      BODY ELECTRICAL > SMART KEY> ACTIVE TEST

      Tester Display Measurement Item Control Range Diagnostic Note
      Overhead Tuner Power Supply ON Door control receiver OFF/ON -
      Power for P-Seat Sens Front door outside handle RH OFF/ON -
      Multi Channel SW Door control receiver CH1/CH2 -
    6. Enter the following menus: Body Electrical / Main Body / Active Test.
    7. Perform Active Test according to the display on the Techstream.
      BODY ELECTRICAL > MAIN BODY > ACTIVE TEST

      Tester Display Measurement Item Control Range Diagnostic Note
      Wireless Buzzer Wireless door lock buzzer OFF/ON -
scientia non olet · About LEMON Manuals