Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch [08/2015 - ]: Procedure

1. Read the Data List according to the display on the Techstream (Refer to DATA LIST / ACTIVE TEST [08/2015 - ] ).
   MAIN BODY
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Communication PDoor Motor	Connection status between front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) / STOP or OK	STOP: Communication stopped OK: Normal communication	-

   OK

   On the Techstream screen, OK is displayed.

Result: 

NG 

GO TO LIN COMMUNICATION SYSTEM 

(Refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2015 - ] )

Result: 

OK 

See step  2

1. Read the Data List according to the display on the Techstream (Refer to DATA LIST / ACTIVE TEST [08/2015 - ] ).
   P-DOOR MOTOR
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   P Door P/W Up SW	Front passenger door power window manual up switch signal / OFF or ON	OFF: Front passenger door power window manual up switch not being operated ON: Front passenger door power window manual up switch being operated	-
   P Door P/W Down SW	Front passenger door power window manual down switch signal / OFF or ON	OFF: Front passenger door power window manual down switch not being operated ON: Front passenger door power window manual down switch being operated	-

   OK

   On the Techstream screen, ON or OFF is displayed accordingly.

Result: 

NG 

See step  4

Result: 

OK 

See step  3

1. Perform the Active Test according to the display on the Techstream (Refer to DATA LIST / ACTIVE TEST [08/2015 - ] ).
   WARNING:

   Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

   P-DOOR MOTOR
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Power Window	Power window	OFF/UP/DOWN	-

   HINT: 

   Up and down movement does not occur if the arrow is not pressed and held.

   OK

   Front passenger door power window operates normally.

Result: 

OK 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

(Refer to REMOVAL [08/2015 - ] )

Result: 

NG 

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH 

(Refer to REMOVAL [08/2015 - ] )

1. Remove the power window regulator switch assembly (Refer to REMOVAL [08/2015 - ] ).
2. Inspect the power window regulator switch assembly (Refer to INSPECTION [08/2015 - ] ).

Result: 

NG 

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY 

(Refer to REMOVAL [08/2015 - ] )

Result: 

OK 

See step  5

1. Disconnect the I3 power window regulator switch assembly connector.
2. Disconnect the I4 front power window regulator motor assembly RH connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   I3-6 (UP) - I4-10 (UP)	Always	Below 1 Ω
   I3-7 (DOWN) - I4-7 (DOWN)	Always	Below 1 Ω
   I3-6 (UP) or I4-10 (UP) - Body ground	Always	10 kΩ or higher
   I3-7 (DOWN) or I4-7 (DOWN) - Body ground	Always	10 kΩ or higher

Result: 

OK 

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH 

(Refer to REMOVAL [08/2015 - ] )

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR