LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2021 >> Land Cruiser Base >> Repair and Diagnosis (Single Page) >> Steering >> Steering Column >> Power Tilt & Telescopic Steering Column - Diagnostics - Introduction >> Power Tilt And Power Telescopic Steering Column System >> Freeze Frame Data [08/2015 - ] >> Freeze Frame Data [08/2015 - ]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Freeze Frame Data [08/2015 - ]

  1. FREEZE FRAME DATA 
    NOTE:
    • Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
    • Turn the engine switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the Techstream.
    1. Turn the engine switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the engine switch on (IG).
    4. Turn the Techstream on.
    5. Check the freeze frame data. Enter the following menus: Body Electrical / Tilt & Telescopic / Trouble Codes.
      TILT & TELESCOPIC

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Tilt Position Current tilt position data/
      Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Position Current telescopic position data/
      Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Return Position Memorized tilt return position data/
      Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Return Position Memorized telescopic return position data/
      Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Up Switch Input state of tilt up switch/
      ON or OFF      		 ON: Tilt up switch activated
      OFF: Tilt up switch not activated      		 -
      Tilt Up SW (CAN) Input state of tilt up switch/
      ON or OFF      		 - -
      Tilt Down Switch Input state of tilt down switch/
      ON or OFF      		 ON: Tilt down switch activated
      OFF: Tilt down switch not activated      		 -
      Tilt Down SW (CAN) Input state of tilt down switch/
      ON or OFF      		 - -
      Telesco Short Switch Input state of telescopic contract switch/
      ON or OFF      		 ON: Telescopic contract switch activated
      OFF: Telescopic contract switch not activated      		 -
      Telesco Short SW (CAN) Input state of telescopic contract switch/
      ON or OFF      		 - -
      Telesco Long Switch Input state of telescopic extend switch/
      ON or OFF      		 ON: Telescopic extend switch activated
      OFF: Telescopic extend switch not activated      		 -
      Telesco Long SW (CAN) Input state of telescopic extend switch/
      ON or OFF      		 - -
      T&T Manual SW Data Voltage data of tilt and telescopic switch/
      Min.: 0.00 V
      Max.: 4.99 V      		 Neutral position: Below 0.2 V
      Tilt up: 1.67 to 2.13 V
      Tilt down: 0.54 to 0.74 V
      Telescopic contract: 1.08 to 1.40 V
      Telescopic extend: 2.22 to 2.77 V      		 -
      Power Source Voltage Voltage data of power supply/
      Min.: 0.00 V
      Max.: 19.99 V      		 11 to 14 V -
      Freeze Speed Info Vehicle speed data/
      Min.: 0 km/h (0 mph)
      Max.: 255 km/h (158 mph)      		 Actual vehicle speed -
      IG Switch (CAN) Communication state of engine switch/
      ON or OFF      		 ON: Communication normal
      OFF: Communication interrupted      		 -
      IG Switch Input state of engine switch/
      ON or OFF      		 ON: Input signal normal
      OFF: Input signal interrupted      		 -
      Receive from Meter Communication state of combination meter assembly signal/
      OK or Interpt      		 OK: Communication normal
      Interpt: Communication interrupted      		 -
      Receive from Seat ECU Communication state of position control ECU signal/
      OK or Interpt      		 OK: Communication normal
      Interpt: Communication interrupted      		 -
      Receive from Combi Communication state of combination switch ECU signal/
      OK or Interpt      		 - -
      J/B Communication state of main body ECU (multiplex network body ECU) signal/
      OK or Interpt      		 OK: Communication normal
      Interpt: Communication interrupted      		 -
      Handle Position Steering wheel position signal/
      Away or Return      		 Away: Steering wheel in away position
      Return: Steering wheel in return position      		 -
      The Number of DTCs Number of stored DTCs/
      Min.: 0
      Max.: 255      		 0 -
scientia non olet · About LEMON Manuals