LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2021 >> Land Cruiser Base >> Repair and Diagnosis >> Restraints >> Restraints Control Systems >> Pre-Collision System - Diagnostic Codes & Circuit Tests >> Pre-Collision System >> DTC C1A47: Steering Angle Sensor [08/2015 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC C1A47: Steering Angle Sensor [08/2015 - ]: Procedure

  1. CHECK DTC OUTPUT (VSC SYSTEM) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
    5. Check for vehicle stability control system DTCs (Refer to DTC CHECK / CLEAR [08/2015 - 08/2017] , or refer to DTC CHECK / CLEAR [08/2017 - ] ).
      RESULT

      Result Proceed to
      Vehicle stability control system DTCs are not output A
      Vehicle stability control system DTCs are output B

      HINT: 

      If the steering sensor is malfunctioning, DTCs for the vehicle stability control system will be stored. Troubleshoot the vehicle stability control system first.

    Result: 

    B 

    GO TO VEHICLE STABILITY CONTROL SYSTEM 

    (Refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2015 - ] )

    Result: 

    A 

    See step  2

  2. CHECK DTC OUTPUT (PRE-COLLISION SYSTEM) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Pre-Collision 2 / Trouble Codes.
    5. Clear the DTCs (Refer to DTC CHECK / CLEAR [08/2015 - ] ).
    6. Drive the vehicle at a speed of 50 km/h (31 mph) or more.

      HINT: 

      If the detection conditions are not met, the system cannot detect the malfunction.

    7. Check for DTCs (Refer to DTC CHECK / CLEAR [08/2015 - ] ).
      RESULT

      Result Proceed to
      DTC C1A47 is output A
      DTC C1A47 is not output B

    Result: 

    B 

    USE SIMULATION METHOD TO CHECK (SYMPTOM SIMULATION) 

    (Refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2015 - 08/2017] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2017 - ] )

    Result: 

    A 

    See step  3

  3. REPLACE DRIVING SUPPORT ECU ASSEMBLY 
    1. Replace the driving support ECU assembly (Refer to REMOVAL [08/2015 - ] ).

    Result: 

    NEXT 

    See step  4

  4. CHECK DTC OUTPUT (PRE-COLLISION SYSTEM) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Pre-Collision 2 / Trouble Codes.
    5. Clear the DTCs (Refer to DTC CHECK / CLEAR [08/2015 - ] ).
    6. Drive the vehicle at a speed of 50 km/h (31 mph) or more.

      HINT: 

      If the detection conditions are not met, the system cannot detect the malfunction.

    7. Check for DTCs (Refer to DTC CHECK / CLEAR [08/2015 - ] ).
      RESULT

      Result Proceed to
      DTC C1A47 is output A
      DTC C1A47 is not output B

    Result: 

    A 

    REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) 

    (Refer to DISASSEMBLY [08/2015 - ] )

    Result: 

    B 

    END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE) 

scientia non olet · About LEMON Manuals