How To Proceed With Troubleshooting [11/2015 - 12/2018]: Procedure

Result

Result: 

NEXT 

See step  2

Result

Result: 

NEXT 

See step  3

1. Measure the auxiliary battery voltage with the power switch off.

   Standard Voltage

   11 to 14 V

   If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Use the Techstream to check if the CAN communication system is functioning normally.

   Refer to DIAGNOSIS SYSTEM [11/2015 - 11/2017] , or refer to DIAGNOSIS SYSTEM [11/2017 - 12/2018]

   Result

   Result	Proceed to
   CAN communication system DTC is not output.	A
   CAN communication system DTC is output.	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2015 - 12/2018] 

Result: 

A 

See step  5

1. Refer to DTC Check / Clear for the blind spot monitor system.

   Refer to DTC CHECK / CLEAR [11/2015 - 12/2018] 

2. Record or print DTCs and freeze frame data, if necessary.

   Refer to FREEZE FRAME DATA [11/2015 - 12/2018] 

   Result

   Result	Proceed to
   DTCs are not output.	A
   DTCs are output.	B

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2015 - 12/2018]  

Result: 

A 

See step  6

1. Refer to Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [11/2015 - 12/2018] 

   Result

   Result	Proceed to
   Fault is not listed in Problem Symptoms Table.	A
   Fault is listed in Problem Symptoms Table.	B

   HINT: 

   If the symptom does not recur and no DTC is output, attempt to reproduce the symptoms.

   Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2015 - 12/2018]

Result: 

B 

GO TO PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [11/2015 - 12/2018]  

Result: 

A 

See step  7

1. Refer to Terminals of ECU.

   Refer to TERMINALS OF ECU [11/2015 - 12/2018] 

2. Refer to Diagnosis System.

   Refer to DIAGNOSIS SYSTEM [11/2015 - 12/2018] 

3. Refer to Data List / Active Test.

   Refer to DATA LIST / ACTIVE TEST [11/2015 - 12/2018] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  8

Result

Result: 

B 

See step  10

Result: 

A 

See step  9

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [11/2015 - 12/2018] 

   Body Electrical > Blind Spot Monitor Master > Clear DTCs 

   Body Electrical > Blind Spot Monitor Slave > Clear DTCs 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  10

1. Enter Test Mode (refer to Blind Spot Monitor Beam Axis Inspection).

   Refer to OPERATION CHECK [11/2015 - 12/2018] 

2. Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

   Refer to OPERATION CHECK [11/2015 - 12/2018] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  11

Result

Result: 

NEXT 

END