Rear Power Window RH does not Operate with Rear Power Window Switch RH [11/2018 - ]: Procedure

1. Using the Techstream, read the data for the condition when the rear power window regulator switch assembly RH was operated.

   Refer to DATA LIST / ACTIVE TEST [11/2018 - 10/2023] , or refer to DATA LIST / ACTIVE TEST [10/2023 - 11/2024] , or refer to DATA LIST / ACTIVE TEST [11/2024 - ]

   Body Electrical > RR-Door Motor > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   RR Door P/W Up SW	Rear RH door power window manual up switch signal	OFF or ON	OFF: Rear RH door power window manual up switch not being operated ON: Rear RH door power window manual up switch being operated	-
   RR Door P/W Down SW	Rear RH door power window manual down switch signal	OFF or ON	OFF: Rear RH door power window manual down switch not being operated ON: Rear RH door power window manual down switch being operated	-

   Body Electrical > RR-Door Motor > Data List 

   Tester Display
   RR Door P/W Up SW
   RR Door P/W Down SW

   OK

   On the Techstream screen, ON or OFF is displayed accordingly.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH 

Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result: 

NG 

See step  2

1. Remove the rear power window regulator switch assembly RH.

   Refer to REMOVAL [11/2018 - ]

2. Inspect the rear power window regulator switch assembly RH.

   Refer to INSPECTION [11/2018 - 12/2021] , or refer to INSPECTION [12/2021 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH 

Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result: 

OK 

See step  3

1. Disconnect the K2 rear power window regulator switch assembly RH connector.
2. Disconnect the K5 rear power window regulator motor assembly RH connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   K2-5 (UP) - K5-10 (UP)	Always	Below 1 Ω
   K2-4 (DOWN) - K5-7 (DOWN)	Always	Below 1 Ω
   K2-5 (UP) or K5-10 (UP) - Body ground	Always	10 kΩ or higher
   K2-4 (DOWN) or K5-7 (DOWN) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH 

Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR