Confirmation Driving Pattern

HINT: 

After a repair, check Monitor Status by performing the Key-Off Monitor Confirmation and Purge Flow Monitor Confirmation described below.

1. KEY-OFF MONITOR CONFIRMATION 
   NOTE:

   • The Evaporative System Check (Automatic Mode) consists of 9 steps performed automatically by the GTS. It takes a maximum of approximately 40 minutes.
   • Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
   • Do not start the engine during this operation.
   • When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature less than 35°C (95°F).
   1. Connect the GTS to the DLC3.
   2. Turn the ignition switch to ON.
   3. Turn the GTS on.
   4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
   5. Turn the ignition switch off and wait for at least 30 seconds.
   6. Turn the ignition switch to ON.
   7. Turn the GTS on.
   8. Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode.
   9. After the "Evaporative System Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine / Utility / All Readiness.
   10. Input the DTC: P043E-00, P043F-00, P0441-7E, P0441-7F, P0446-72, P4467-3, P0450-11, P0450-15, P0450-2F, P1420-00, P1421-00, P1422-00, P1423-00, P1450-11, P1450-15, P1450-2A, P1450-2F, P2400-7E, P2400-7F, P2450-7E or P2451-7F.
   11. Check the DTC judgment result.

       GTS Display	Description
       NORMAL	DTC judgment completed System normal
       ABNORMAL	DTC judgment completed System abnormal
       INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions

       HINT: 

       • If the judgment result is NORMAL, the system is normal.
       • If the judgment result is ABNORMAL, the system is malfunctioning.
2. PURGE FLOW MONITOR CONFIRMATION (P0441-9C) 

   HINT: 

   Perform this monitor confirmation after the Key-Off Monitor Confirmation shows Complete.

   1. Connect the GTS to the DLC3.
   2. Turn the ignition switch to ON.
   3. Turn the GTS on.
   4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
   5. Turn the ignition switch off and wait for at least 30 seconds.
   6. Turn the ignition switch to ON.
   7. Turn the GTS on.
   8. Put the engine in Inspection Mode (Maintenance Mode).

      Refer to INSPECTION MODE PROCEDURE [06/2020 - ]

   9. Start the engine and wait 15 minutes or more.
   10. Enter the following menus: Powertrain / Engine / Trouble Codes.
   11. Read the pending DTCs.

       HINT: 

       • If a pending DTC is output, the system is malfunctioning.
       • If a pending DTC is not output, perform the following procedure.
   12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
   13. Input the DTC: P0441-9C.
   14. Check the DTC judgment result.

       GTS Display	Description
       NORMAL	DTC judgment completed System normal
       ABNORMAL	DTC judgment completed System abnormal
       INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions

       HINT: 

       • If the judgment result is NORMAL, the system is normal.
       • If the judgment result is ABNORMAL, the system is malfunctioning.