Data List / Active Test [08/2015 - 08/2019]

READ DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / (desired system) / Data List.

According to the display on the Techstream, read the Data List.

MASTER SWITCH

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
D Door P/W Auto SW	Driver side power window auto UP/DOWN switch signal / ON or OFF	ON: Driver side power window auto UP/DOWN switch on power window regulator master switch operated OFF: Driver side power window switch on power window regulator master switch not operated	-
P Door P/W Auto SW	Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF	ON: Front passenger side power window remote auto UP/DOWN switch on power window regulator master switch operated OFF: Front passenger side power window switch on power window regulator master switch not operated	-
P Door P/W Up SW	Front passenger side power window remote manual UP switch signal / ON or OFF	ON: Front passenger side power window remote manual UP switch on power window regulator master switch operated OFF: Front passenger side power window switch on power window regulator master switch not operated	-
P Door P/W Down SW	Front passenger side power window remote manual DOWN switch signal / ON or OFF	ON: Front passenger side power window remote manual DOWN switch on power window regulator master switch operated OFF: Front passenger side power window switch on power window regulator master switch not operated	-
Window Lock Switch Status	Power window LOCK switch / ON or OFF	ON: The Power window lock switch LOCK position OFF: The Power window lock switch UNLOCK position	-
Number of Trouble Codes	Number of trouble codes / Min.: 0, Max.: 255	Number of DTCs will be displayed	-

D-DOOR MOTOR

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
D Door P/W Auto SW	Driver side power window auto UP/DOWN switch signal / ON or OFF	ON: Driver side power window auto UP/DOWN switch operated OFF: Driver side power window switch not operated	-
D Door P/W Up SW	Driver side power window MANUAL UP switch signal / ON or OFF	ON: Driver side power window manual UP switch operated OFF: Driver side power window switch not operated	-
D Door P/W Down SW	Driver side power window MANUAL DOWN switch signal / ON or OFF	ON: Driver side power window manual DOWN switch operated OFF: Driver side power window switch not operated	-
Number of Trouble Codes	Number of trouble codes / Min.: 0, Max.: 255	Number of DTCs will be displayed	-

P-DOOR MOTOR

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
P Door P/W Auto SW	Front passenger side power window auto UP/DOWN switch signal / ON or OFF	ON: Front passenger side power window auto UP/DOWN switch operated OFF: Front passenger side power window regulator switch not operated	-
P Door P/W Up SW	Front passenger side power window manual UP switch signal / ON or OFF	ON: Front passenger side power window manual UP switch operated OFF: Front passenger side power window regulator switch not operated	-
P Door P/W Down SW	Front passenger side power window manual DOWN switch signal / ON or OFF	ON: Front passenger side power window manual DOWN switch operated OFF: Front passenger side power window regulator switch not operated	-
Number of Trouble Codes	Number of trouble codes / Min.: 0, Max.: 255	Number of DTCs will be displayed	-

MAIN BODY

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
D Door Courtesy SW	Driver side door courtesy switch signal / ON or OFF	ON: Driver door open OFF: Driver door closed	-
P Door Courtesy SW	Front passenger side door courtesy switch signal / ON or OFF	ON: Front passenger door open OFF: Front passenger door closed	-
Door Lock SW-Lock	Driver side door lock switch signal / ON or OFF	ON: Driver side door lock switch is turned to lock OFF: Key is in Driver side door lock key cylinder (original position)	-
Door Lock SW-Unlock	Driver side door unlock switch signal / ON or OFF	ON: Driver side door lock switch is turned to unlock OFF: Key is in Driver side door lock key cylinder (original position)	-
Door Key P/W Up	Function to roll the driver side door window down while holding the key to the unlock side more than about 0.7 second. / ON or OFF	Customize setting displayed	-
Door Key P/W Down	Function to roll the driver side door window up while holding the key to the lock side more than about 0.7 second. / NOT ON or OFF	Customize setting displayed	-
Communication D-Door Motor	Connection status between power window regulator motor (for driver side) and main body ECU/OK or Stop	OK: Connection Stop: No connection	-
Communication P-Door Motor	Connection status between power window regulator motor (for front passenger side) and main body ECU/OK or Stop	OK: Connection Stop: No connection	-
Communication Master SW	Connection status between master switch and main body ECU/OK or Stop	OK: Connection Stop: No connection	-
Communication B-Dor P/W	Connection status between back door ECU and main body ECU/OK or Stop	OK: Connection Stop: No connection	-

BACK DOOR P/W

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Key Switch Operation Locked	Tail gate control switch signal / ON or OFF	ON: Tail gate control switch is turned to unlock OFF: Key is in back door lock key cylinder (original position)	-
Key Switch Operation Unlocked	Tail gate control switch signal / ON or OFF	ON: Tail gate control switch is turned to unlock OFF: Key is in back door lock key cylinder (original position)	-
Wiper Reverse Position	Rear wiper reverse position switch signal / ON or OFF	ON: Rear wiper reverse position switch is in ON position OFF: Rear wiper reverse position switch is in OFF position	-
Wiper Retracted Position	Rear wiper retract switch signal / ON or OFF	ON: Rear wiper retract switch is in ON position OFF: Rear wiper retract switch is in OFF position	-
Door Key Linked Unlock SW	Function to roll the back door window down while holding the key to the unlock side more than about 0.7 second. / NOT AVL or AVAIL	Customize setting displayed	-
Door Key Linked Lock SW	Function to roll the back door window up while holding the key to the lock side more than about 0.7 second. / NOT AVL or AVAIL	Customize setting displayed	-
Back Door P/W Status	Back door glass position signal / CLOSE or OPEN	CLOSE: Back door glass is in CLOSE position OPEN: Back door glass is in OPEN position	-
Back P/W Pos (Close-1/4 open)	Door glass position (Fully closed - 1/ 4 open) signal / OK or CAUTION	OK: Power window is going UP by manual operation CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position	-
Back P/W Pos (1/4-2/4 open)	Door glass position (1/4 open - 2/4 open) signal / OK or CAUTION	OK: Power window is going UP by manual operation CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position	-
Back P/W Pos (2/4-3/4 open)	Door glass position (2/4 open - 3/4 open) signal / OK or CAUTION	OK: Power window is going UP by manual operation CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position	-
Back P/W Pos (3/4-Full open)	Door glass position (3/4 open - Fully open) signal / OK or CAUTION	OK: Power window is going UP by manual operation CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position	-

PERFORM ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / (desired system) / Active Test.

According to the display on the Techstream, perform the Active Test.

HINT:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.

D-DOOR MOTOR

Tester Display	Test Part	Control Range	Diagnostic Note
Power Window	Driver side power window	OFF/UP/DOWN	-

P-DOOR MOTOR

Tester Display	Test Part	Control Range	Diagnostic Note
Power Window	Front passenger side power window	OFF/UP/DOWN	-

BACK DOOR P/W

Tester Display	Test Part	Control Range	Diagnostic Note
Back Door Power Window	Back door power window	OFF/UP/DOWN	-

MAIN BODY

Tester Display	Test Part	Control Range	Diagnostic Note
IG OFF P/W Control Permission Output	Power window control permission output	ON or OFF	-