Back Door Entry Lock Function does not Operate [08/2019 - ]: Procedure

1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

   Refer to OPERATION CHECK [08/2019 - ]

   OK

   Door locks operate normally.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO POWER DOOR LOCK CONTROL SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2019 - ] 

Result: 

OK 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Key / Data List.
5. Read the Data List according to the display on the Techstream.
   BODY ELECTRICAL > SMART KEY > DATA LIST
   
   

   Tester Display	Measurement Item	Range	Normal Condition	Normal Condition
   Tr/B-Door Lock SW	Tail gate control switch assembly (lock switch)	ON or OFF	ON: Tail gate control switch assembly (lock switch) pressed OFF: Tail gate control switch assembly (lock switch) not pressed	Displays whether the tail gate control switch assembly (lock switch) is on or off. Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.

   HINT: 

   When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function. Other door lock operations, such as a wireless door lock operation, can be performed consecutively.

   OK

   The Techstream display changes correctly in response to the operation of the tail gate control switch assembly.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY). Refer to  REMOVAL [08/2019 - ] 

Result: 

NG 

See step  3

1. Disconnect the H133 main body ECU (multiplex network body ECU) connector.
2. Connect the Techstream to the DLC3.
3. Turn the engine switch on (IG).
4. Turn the Techstream on.
5. Enter the following menus: Body Electrical / Smart Key / Data List.
6. Read the Data List according to the display on the Techstream.
   BODY ELECTRICAL > SMART KEY > DATA LIST
   
   

   Tester Display	Measurement Item	Range	Normal Condition	Normal Condition
   Tr/B-Door Lock SW	Tail gate control switch assembly (lock switch)	ON or OFF	ON: Tail gate control switch assembly (lock switch) pressed OFF: Tail gate control switch assembly (lock switch) not pressed	Displays whether the tail gate control switch assembly (lock switch) is on or off. Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.

   HINT: 

   When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function. Other door lock operations, such as a wireless door lock operation, can be performed consecutively.

   OK

   The Techstream display changes correctly in response to the operation of the tail gate control switch assembly.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [08/2019 - ] 

Result: 

NG 

See step  4

1. Disconnect the V24 tail gate control switch assembly connector.
2. Disconnect the H198 certification ECU (smart key ECU assembly) connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   V24-1 (SUP) - H198-13 (TSW6)	Always	Below 1 Ω
   V24-1 (SUP) or H198-13 (TSW6) - Other terminals and body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  5

1. Remove the tail gate control switch assembly.

   Refer to REMOVAL [08/2019 - ]

2. Inspect the tail gate control switch assembly.

   Refer to INSPECTION [08/2019 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY). Refer to  REMOVAL [08/2019 - ] 

Result: 

NG 

REPLACE TAIL GATE CONTROL SWITCH ASSEMBLY. Refer to  REMOVAL [08/2019 - ]