LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2025 >> GR86 Base, Automatic Trans >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Anti-Theft Systems >> Keyless Access System - Diagnostics - Introduction >> Keyless Access System With Push Button Start >> Registration [11/2021 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Registration [11/2021 - ]: Procedure

  1. REPAIR INSTRUCTION 
    WARNING:

    As weak radio waves are emitted from the electrical key transmitter sub-assembly, if a pacemaker is being used, be sure to read the pacemaker instruction manual and the following.

    • People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should keep away from the keyless access system antennas. The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your dealer for details, such as the frequency of radio waves and timing of the emitted radio waves. Then, consult your doctor to see if you should disable the entry function.

      Refer to PARTS LOCATION [11/2021 - ] 

    • User of any electrical medical device other than implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.
    • Ask your dealer for details for disabling the keyless access system with push button start.

      Refer to CUSTOMIZE PARAMETERS [11/2021 - ] 

    NOTE:

    PRECAUTION WHEN REPLACING PARTS

    • Code registration is necessary when any of the following parts is replaced with a new one. After replacing a part, any part that has performed registration cannot be returned.
      • Smart key ECU assembly
      • Immobilizer code ECU*
      • Steering lock actuator assembly
      • Electrical key transmitter sub-assembly
        1. *: w/ Immobilizer Code ECU

    PRECAUTION FOR REGISTRATION

    • Make sure that only 1 electrical key transmitter sub-assembly is in the cabin during registration procedures. If 2 or more electrical key transmitter sub-assemblies are in the cabin simultaneously, the electric waves will interfere with each other, preventing normal registration.
    • A maximum of 7 electrical key transmitter sub-assemblies can be registered (this includes any electrical key transmitter sub-assembly registered when the vehicle was purchased).
    • If the auxiliary battery is depleted during the electrical key transmitter sub-assembly registration procedure, there may be cases in which the electrical key transmitter sub-assembly cannot be registered again. Therefore, make sure to perform work with a sufficiently charged battery.
    • If any of the work times are exceeded, finish the procedure.
    • Do not disconnect the auxiliary battery during the Registration.
    • Do not perform operations that create an electrical load such as operating the power windows.
    • If "Keyless Access System with Push Button Start" is canceled, registration cannot be performed.

      Refer to CUSTOMIZE PARAMETERS [11/2021 - ] 

  2. EXPLANATION OF IMMOBILISER KEY ID REGISTRATION PROCEDURE 
    1. Addressing customer requests (perform work in chart below in order starting from left)
      W/ IMMOBILIZER CODE ECU:

      Customer Request/Condition Immobilizer key ID deletion Replace smart key ECU assembly Replace immobilizer code ECU New key ID registration Additional key ID registration Telematics transceiver registration
      Refer to PROCEDURE 5 Refer to REMOVAL [11/2021 - ] Refer to REMOVAL [11/2021 - ] 3 4 8
      All electrical key transmitter sub-assemblies are lost - -
      Registering additional electrical key transmitter sub-assembly - - - - -
      Making a lost electrical key transmitter sub-assembly unusable - - - - -
      W/O IMMOBILIZER CODE ECU:

      Customer Request/Condition Immobilizer key ID deletion Replace smart key ECU assembly Replace steering lock actuator assembly New key ID registration Additional key ID registration Telematics transceiver registration
      Refer to PROCEDURE 5 Refer to REMOVAL [11/2021 - ] Refer to DISASSEMBLY [11/2021 - ] 3 4 8
      All electrical key transmitter sub-assemblies are lost - -
      Registering additional electrical key transmitter sub-assembly - - - - -
      Making a lost electrical key transmitter sub-assembly unusable - - - - -
    2. Addressing malfunctions 1 (perform work in chart below in order starting from left)
      SMART KEY ECU ASSEMBLY MALFUNCTION (W/ IMMOBILIZER CODE ECU)

      Condition
      (The number of the electrical key transmitter sub-assemblies customer has brought)      		 Immobilizer key ID deletion Replace smart key ECU assembly Replace immobilizer code ECU New key ID registration Telematics transceiver registration
      Refer to PROCEDURE 5 Refer to REMOVAL [11/2021 - ] Refer to REMOVAL [11/2021 - ] 3 8
      All electrical key transmitter sub-assemblies - -
      At least 1 electrical key transmitter sub-assembly
      (Key ID codes can be registered and cleared)      		 -
      At least 1 electrical key transmitter sub-assembly
      (Key ID codes cannot be either registered or cleared)      		 -
      All electrical key transmitter sub-assemblies are lost -
      SMART KEY ECU ASSEMBLY MALFUNCTION (W/O IMMOBILIZER CODE ECU)

      Condition
      (The number of the electrical key transmitter sub-assemblies customer has brought)      		 Immobilizer key ID deletion Replace smart key ECU assembly Replace steering lock actuator assembly New key ID registration Telematics transceiver registration
      Refer to PROCEDURE 5 Refer to REMOVAL [11/2021 - ] Refer to DISASSEMBLY [11/2021 - ] 3 8
      All electrical key transmitter sub-assemblies - -
      At least 1 electrical key transmitter sub-assembly
      (Key ID codes can be registered and cleared)      		 -
      At least 1 electrical key transmitter sub-assembly
      (Key ID codes cannot be either registered or cleared)      		 -
      All electrical key transmitter sub-assemblies are lost -
    3. Addressing malfunctions 2 (perform work in chart below in order starting from left)
      ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLIES MALFUNCTION (W/ IMMOBILIZER CODE ECU)

      Condition
      (The number of the electrical key transmitter sub-assemblies customer has brought)      		 Immobilizer key ID deletion Replace smart key ECU assembly Replace immobilizer code ECU New key ID registration Additional key ID registration Telematics transceiver registration
      Refer to PROCEDURE 5 Refer to REMOVAL [11/2021 - ] Refer to REMOVAL [11/2021 - ] 3 4 8
      One or more electrical key transmitter sub-assembly that operates normally - - - -
      All electrical key transmitter sub-assemblies are lost - -
      ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLIES MALFUNCTION (W/O IMMOBILIZER CODE ECU)

      Condition
      (The number of the electrical key transmitter sub-assemblies customer has brought)      		 Immobilizer key ID deletion Replace smart key ECU assembly Replace steering lock actuator assembly New key ID registration Additional key ID registration Telematics transceiver registration
      Refer to PROCEDURE 5 Refer to REMOVAL [11/2021 - ] Refer to DISASSEMBLY [11/2021 - ] 3 4 8
      One or more electrical key transmitter sub-assembly that operates normally - - - -
      All electrical key transmitter sub-assemblies are lost - -
    4. Addressing malfunctions 3 (perform work in chart below in order starting from left)
      IMMOBILIZER CODE ECU MALFUNCTION (W/ IMMOBILIZER CODE ECU)

      Condition
      (The number of the electrical key transmitter sub-assemblies customer has brought)      		 Replace smart key ECU assembly Replace immobilizer code ECU New key ID registration Steering lock actuator assembly/immobilizer code ECU registration Engine control module registration Telematics transceiver registration
      Refer to PROCEDURE Refer to REMOVAL [11/2021 - ] Refer to REMOVAL [11/2021 - ] 3 6 7 8
      One or more electrical key transmitter sub-assembly that operates normally - - -
      All electrical key transmitter sub-assemblies are lost - -
    5. Addressing malfunctions 4 (perform work in chart below in order starting from left)
      STEERING LOCK ACTUATOR ASSEMBLY MALFUNCTION (W/ IMMOBILIZER CODE ECU)

      Condition
      (The number of the electrical key transmitter sub-assemblies customer has brought)      		 Replace smart key ECU assembly Replace immobilizer code ECU Replace steering lock actuator assembly New key ID registration Steering lock actuator assembly/immobilizer code ECU registration Telematics transceiver registration
      Refer to PROCEDURE Refer to REMOVAL [11/2021 - ] Refer to REMOVAL [11/2021 - ] Refer to DISASSEMBLY [11/2021 - ] 3 6 8
      One or more electrical key transmitter sub-assembly that operates normally - - - -
      All electrical key transmitter sub-assemblies are lost -
      STEERING LOCK ACTUATOR ASSEMBLY MALFUNCTION (W/O IMMOBILIZER CODE ECU)

      Condition
      (The number of the electrical key transmitter sub-assemblies customer has brought)      		 Replace smart key ECU assembly Replace steering lock actuator assembly New key ID registration Steering lock actuator assembly/immobilizer code ECU registration Telematics transceiver registration
      Refer to PROCEDURE Refer to REMOVAL [11/2021 - ] Refer to DISASSEMBLY [11/2021 - ] 3 6 8
      One or more electrical key transmitter sub-assembly that operates normally - - -
      All electrical key transmitter sub-assemblies are lost -
    6. Addressing malfunctions 5 (perform work in chart below in order starting from left)
      W/ IMMOBILIZER CODE ECU

      Malfunctioning ECU Condition Replace smart key ECU assembly Replace immobilizer code ECU Replace ECM Replace telematics transceiver New key ID registration Engine control module registration Telematics transceiver registration
      Refer to PROCEDURE Refer to REMOVAL [11/2021 - ] Refer to REMOVAL [11/2021 - ] Refer to REMOVAL [11/2021 - ] Refer to REMOVAL [11/2021 - ] 3 7 8
      ECM One or more electrical key transmitter sub-assembly that operates normally - - - - -
      All electrical key transmitter sub-assemblies are lost - -
      Replace telematics transceiver - - - - -
      W/O IMMOBILIZER CODE ECU

      Malfunctioning ECU Condition Replace smart key ECU assembly Replace steering lock actuator assembly Replace ECM Replace telematics transceiver New key ID registration Engine control module registration Telematics transceiver registration
      Refer to PROCEDURE Refer to REMOVAL [11/2021 - ] Refer to DISASSEMBLY [11/2021 - ] Refer to REMOVAL [11/2021 - ] Refer to REMOVAL [11/2021 - ] 3 7 8
      ECM One or more electrical key transmitter sub-assembly that operates normally - - - - -
      All electrical key transmitter sub-assemblies are lost - -
      Replace telematics transceiver - - - - -
  3. NEW KEY ID REGISTRATION 
    NOTE:
    • When the smart key ECU assembly is replaced, register all electrical key transmitter sub-assemblies used by the customer.
    • Registered electrical key transmitter sub-assemblies other than those registered during the smart key ECU assembly replacement cannot be re-registered, and therefore they can no longer be used.
    • Immediately after replacing the smart key ECU assembly, the GTS item "Confirmed number of all registered keys" should change to "0". If this item does not change to "0", the smart key ECU assembly may be registered to another vehicle. A smart key ECU assembly which is registered to another vehicle cannot be used.
    Process Procedure Time limit
    (seconds)
    1. Start of registration
    1. Ignition switch off.
    2. Connect the GTS to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the GTS on.
    5. Enter the following menus: Body Electrical / Keyless Access with Push Button Start(Collation) / Utility / Keyless Access Immobilizer Registration
    		 -
    2. Get Pass-Code
    1. According to the display on the GTS, obtain the Pass-Code using online authentication or proxy authentication.
      NOTE:

      After obtaining the Pass-Code, do not turn off the GTS until registration is completed. If the GTS is turned off before registration is completed, obtain the Pass-Code once more.

    		 -
    3. Confirmation of all registered electrical key transmitter sub-assemblies
    (When only the smart key ECU assembly is replaced)
    1. While facing the logo side of a registered electrical key transmitter sub-assembly toward the engine switch, hold the electrical key transmitter sub-assembly near engine switch.
    2. Confirm that the wireless door lock buzzer sounds once (short beep).
    3. Repeat procedure 1 and 2 of this process for all the previously registered electrical key transmitter sub-assemblies.
    		 30
    4. Verification of unregistered electrical key transmitter sub-assembly
    1. While facing the logo side of an unregistered electrical key transmitter sub-assembly toward the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.
    2. Confirm that the wireless door lock buzzer sounds twice (short beep).
    3. Repeat procedure 1 and 2 of this process for all electrical key transmitter sub-assemblies to register.
    		 30
    5. ECM registration
    1. According to the display on the GTS, turn the ignition switch off.
    2. According to the display on the GTS, turn the ignition switch to ON.
    		 procedure 1: 60
    procedure 2: 60
    6. End of registration Finish new key ID code registration. -
  4. ADDITIONAL KEY ID REGISTRATION 
    Process Procedure Time limit
    (seconds)
    1. Start of registration
    1. Ignition switch off.
    2. Connect the GTS to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the GTS on.
    5. Enter the following menus: Body Electrical / Keyless Access with Push Button Start(Collation) / Utility / Keyless Access Immobilizer Registration
    		 -
    2. Get Pass-Code
    1. According to the display on the GTS, obtain the Pass-Code using online authentication or proxy authentication.
      NOTE:

      After obtaining the Pass-Code, do not turn off the GTS until registration is completed. If the GTS is turned off before registration is completed, obtain the Pass-Code once more.

    		 -
    3. Confirmation of registered electrical key transmitter sub-assemblies
    1. While facing the logo side of a registered electrical key transmitter sub-assembly toward the engine switch, hold the electrical key transmitter sub-assembly near engine switch.
    2. Confirm that the wireless door lock buzzer sounds once (short beep).
    HINT: When checking registered electrical key transmitter sub-assemblies, check using an electrical key transmitter sub-assembly that is registered to the vehicle.    		 30
    4. Verification of unregistered electrical key transmitter sub-assembly
    1. While facing the logo side of an unregistered electrical key transmitter sub-assembly toward the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.
    2. Confirm that the wireless door lock buzzer sounds twice (short beep).
    3. Repeat procedure 1 and 2 of this process for all electrical key transmitter sub-assemblies to register.
    		 30
    5. ECM registration
    1. According to the display on the GTS, turn the ignition switch off.
    2. According to the display on the GTS, turn the ignition switch to ON.
    		 procedure 1: 60
    procedure 2: 60
    6. End of registration Finish additional key ID code registration. -
  5. IMMOBILIZER KEY ID DELETION REGISTRATION 
    NOTE:

    If Immobilizer Key ID Deletion is performed, previously registered electrical key transmitter sub-assemblies cannot be re-registered, and therefore they can no longer be used.

    HINT: 

    Immobilizer Key ID Deletion can be used to delete and disable all key IDs other than the electrical key transmitter sub-assemblies selected during "confirmation of registered electrical key transmitter sub-assemblies to keep (process No. 3)".

    Process Procedure Time limit
    (seconds)
    1. Start of erasure
    1. Ignition switch off.
    2. Connect the GTS to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the GTS on.
    5. Enter the following menus: Body Electrical / Keyless Access with Push Button Start(Collation) / Utility / Immobilizer Access Key ID Deletion
    		 -
    2. Get Pass-Code
    1. According to the display on the GTS, obtain the Pass-Code using online authentication or proxy authentication.
      NOTE:

      After obtaining the Pass-Code, do not turn off the GTS until registration is completed. If the GTS is turned off before registration is completed, obtain the Pass-Code once more.

    		 -
    3. Confirmation of registered electrical key transmitter sub-assemblies to keep
    1. While facing the logo side of a registered electrical key transmitter sub-assembly toward the engine switch, hold the electrical key transmitter sub-assembly near engine switch.
    2. Confirm that the wireless door lock buzzer sounds once (short beep).
    HINT: When checking registered electrical key transmitter sub-assemblies, check using an electrical key transmitter sub-assembly that is registered to the vehicle.    		 30
    4. Erasure of ID code
    1. Check that key ID erase completion message is shown on the GTS.
    		 -
    5. End of erasure Finish key ID erasure. -
  6. STEERING LOCK ACTUATOR ASSEMBLY/ID CODE BOX REGISTRATION 
    Process Procedure Time limit
    (seconds)
    1. Start of registration
    1. Ignition switch off.
    2. Connect the GTS to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the GTS on.
    5. Enter the following menus: Body Electrical / Keyless Access with Push Button Start(Collation) / Utility / Steering Lock CM/ID Code Box Registration
    		 -
    2. Get Pass-Code
    1. According to the display on the GTS, obtain the Pass-Code using online authentication or proxy authentication.
      NOTE:

      After obtaining the Pass-Code, do not turn off the GTS until registration is completed. If the GTS is turned off before registration is completed, obtain the Pass-Code once more.

    		 -
    3. Confirmation of registered electrical key transmitter sub-assemblies
    1. While facing the logo side of a registered electrical key transmitter sub-assembly toward the engine switch, hold the electrical key transmitter sub-assembly near engine switch.
    2. Confirm that the wireless door lock buzzer sounds once (short beep).
    HINT: When checking registered electrical key transmitter sub-assemblies, check using an electrical key transmitter sub-assembly that is registered to the vehicle.    		 30
    4. Steering lock actuator assembly/immobilizer code ECU registration
    1. Perform operations according to prompts on the GTS screen.
    		 -
    5. End of registration Finish Steering Lock CM/ID Code Box registration. -
  7. ENGINE CONTROL MODULE REGISTRATION 
    NOTE:

    Do not open or close the driver door during registration. If the driver door is opened or closed, restart from step 1 of "Start of registration".

    Process Procedure
    1. Start of registration
    1. Ignition switch off.
    2. Connect the GTS to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the GTS on.
    5. Enter the following menus: Body Electrical / Keyless Access with Push Button Start(Collation) / Utility / Engine Control Module Registration
    2. Get Pass-Code
    1. According to the display on the GTS, obtain the Pass-Code using online authentication or proxy authentication.
      NOTE:

      After obtaining the Pass-Code, do not turn off the GTS until registration is completed. If the GTS is turned off before registration is completed, obtain the Pass-Code once more.
    3. Engine control module registration
    1. Perform operations according to prompts on the GTS screen.
    4. End of registration Finish engine control module registration.
  8. TELEMATICS TRANSCEIVER REGISTRATION 
    NOTE:

    Do not open or close the driver door during registration. If the driver door is opened or closed, restart from step 1 of "Start of registration".

    Process Procedure
    1. Start of registration
    1. Ignition switch off.
    2. Connect the GTS to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the GTS on.
    5. Enter the following menus: Body Electrical / Keyless Access with Push Button Start(Collation) / Utility / Telematics CM Registration
    2. Get Pass-Code
    1. According to the display on the GTS, obtain the Pass-Code using online authentication or proxy authentication.
      NOTE:

      After obtaining the Pass-Code, do not turn off the GTS until registration is completed. If the GTS is turned off before registration is completed, obtain the Pass-Code once more.
    3. Telematics transceiver registration
    1. Perform operations according to prompts on the GTS screen.
    4. End of registration Finish telematics transceiver registration.
scientia non olet · About LEMON Manuals