When the Passenger's Switch is Operated, the Passenger's Side Power Window does not Work in Automatic Operation [11/2021 - ]: Procedure

1. Turn the ignition switch to ON.
2. Operate the power window regulator master switch assembly and check that the power window (passenger's side) works in manual operation.

   Does the power window operate manually according to switch operation?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

PERFORM THE DIAGNOSIS FOR "WHEN THE PASSENGER'S SWITCH IS OPERATED, THE PASSENGER'S SIDE POWER WINDOW DOES NOT WORK IN MANUAL OPERATION". Refer to  When the Passenger's Switch is Operated, the Passenger's Side Power Window does not Work in Manual Operation [11/2021 - ]  

Result: 

A 

See step  2

1. Using the GTS, read the DTCs of [Power Window (Switch)] and [Power Window (Passenger)].

   Body Electrical > Power Window (Switch) > Trouble Codes 

   Body Electrical > Power Window (Passenger) > Trouble Codes 

   Are any DTCs displayed?

   Result	Proceed to
   YES	A
   NO	B

Result: 

A 

PERFORM THE DIAGNOSIS FOR THE DISPLAYED DTCS 

Result: 

B 

See step  3

1. Using the GTS, check the following items in the [Data List] of [Power Window (Passenger)].

   Body Electrical > Power Window (Passenger) > Data List 

   Tester Display	Measurement Item	Range	Diagnostic Note
   ECU Control Mode	ECM control status	Uninitialized 1 No Definition Uninitialized 2 Initialized	-

   Body Electrical > Power Window (Passenger) > Data List 

   Tester Display
   ECU Control Mode

   Is [Initialized] displayed?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

USING THE GTS, PERFORM [SYSTEM INITIALIZATION] OF [POWER WINDOW (PASSENGER)] 

Refer to UTILITY [11/2021 - ]

Then, perform the initial setting of the power window.

Refer to REGISTRATION [11/2021 - ]

Result: 

A 

See step  4

1. Using the GTS, check the following items in the [Data List] of [Power Window (Passenger)].

   Body Electrical > Power Window (Passenger) > Data List 

   Tester Display	Measurement Item	Range	Diagnostic Note
   One's Seat Switch	Status of switch at passenger's own seat	OFF DOWN UP UP/DOWN AUTO AUTO DOWN AUTO UP UP/DOWN/AUTO	-

   Body Electrical > Power Window (Passenger) > Data List 

   Tester Display
   One's Seat Switch

   Does the display change corresponding to the switch operation?

   Result	Proceed to
   YES	A
   NO	B

Result: 

A 

REPLACE THE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH. Refer to  REMOVAL [11/2021 - ] 

Result: 

B 

See step  5

1. Turn the ignition switch to OFF.
2. Disconnect the power window regulator switch assembly connector.
3. Perform the inspection of power window regulator switch assembly.

   Refer to INSPECTION [11/2021 - ]

   Is the check result OK?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

REPLACE THE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

Result: 

A 

See step  6

1. Disconnect the power window regulator motor assembly RH connector.
2. Using a tester, measure the resistance between power window regulator switch assembly connector and power window regulator motor assembly RH connector.

   Connector & terminal

   H3-1 - H5-4

   Is the resistance less than 1 Ω?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

REPAIR THE HARNESS 

Repair the open circuit of the harness between power window regulator switch assembly connector and power window regulator motor assembly RH connector.

Result: 

A 

See step  7

1. Turn the ignition switch to ON.
2. Using a tester, measure the voltage between the power window regulator switch assembly connector and chassis ground.

   Connector & terminal

   H3-1 - Chassis ground

   Is the voltage less than 1 V?

   Result	Proceed to
   YES	A
   NO	B

Result: 

A 

REPLACE THE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH. Refer to  REMOVAL [11/2021 - ] 

Result: 

B 

REPAIR THE HARNESS 

Repair the short circuit to power supply in the harness between power window regulator switch assembly connector and power window regulator motor assembly RH connector.