When the Passenger's Switch is Operated, the Passenger's Side Power Window does not Work in Manual Operation [11/2021 - ]: Procedure

1. Turn the ignition switch to OFF.
2. Check the battery.

   Refer to ON-VEHICLE INSPECTION [11/2021 - ]

   Is the check result OK?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

CHARGE OR REPLACE THE BATTERY 

Result: 

A 

See step  2

1. Check the fuse.

   Is the check result OK?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

REPLACE THE FUSE. WHEN THE REPLACED FUSE IS BLOWN IMMEDIATELY, REPAIR THE POWER SUPPLY CIRCUIT. 

Result: 

A 

See step  3

1. Check the ignition switch.

   Is the ignition switch ON?

   Result	Proceed to
   YES	A
   NO (Turn the ignition switch to ON.)	B

Result: 

B 

See step  4

Result: 

A 

See step  4

1. Check the window lock switch.

   Is the window lock switch unlocked?

   Result	Proceed to
   YES	A
   NO (Unlock the window lock switch)	B

Result: 

B 

See step  5

Result: 

A 

See step  5

1. Using the GTS, read the DTCs of [Power Window (Switch)] and [Power Window (Passenger)].

   Body Electrical > Power Window (Switch) > Trouble Codes 

   Body Electrical > Power Window (Passenger) > Trouble Codes 

   Are any DTCs displayed?

   Result	Proceed to
   YES	A
   NO	B

Result: 

A 

PERFORM THE DIAGNOSIS FOR THE DISPLAYED DTCS 

Result: 

B 

See step  6

1. Using the GTS, read all DTCs.

   Refer to DIAGNOSIS SYSTEM [11/2021 - ]

   Is DTC of U-code displayed?

   Result	Proceed to
   YES	A
   NO	B

Result: 

A 

PERFORM THE DIAGNOSIS FOR CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2021 - ] 

Result: 

B 

See step  7

1. Turn the ignition switch to OFF.
2. Check that the following connectors are properly connected.
   • Power window regulator switch assembly connector
   • Power window regulator motor assembly RH connector

   Is the check result OK?

   Result	Proceed to
   YES	A
   NO (Connect the connector correctly) HINT:  Repair the connector if any broken pin or poor mating is detected.	B

Result: 

B 

See step  7

Result: 

A 

See step  8

1. Turn the ignition switch to ON.
2. Operate the power window regulator switch assembly and check that the power window (passenger's side) operates.

   Is the symptom removed?

   Result	Proceed to
   YES	A
   NO	B

Result: 

A 

SINCE THE POOR CONTACT OF CONNECTOR WAS REPAIRED, THE CIRCUIT CONDITION RETURNED TO NORMAL 

Result: 

B 

See step  9

1. Turn the ignition switch to OFF.
2. Disconnect the power window regulator motor assembly RH connector.
3. Turn the ignition switch to ON.
4. Using a tester, measure the voltage between the power window regulator motor assembly RH connector and chassis ground.

   Connector & terminal

   H5-5 - Chassis ground

   Is the voltage 10.0 V or more?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

CHECK THE POWER SUPPLY CIRCUIT 

Result: 

A 

See step  10

1. Using the GTS, check the following items in the [Data List] of [Power Window (Passenger)].

   Body Electrical > Power Window (Passenger) > Data List 

   Tester Display	Measurement Item	Range	Diagnostic Note
   Operation Enable Signal	Operation permission signal	Not Permit Permit	-

   Body Electrical > Power Window (Passenger) > Data List 

   Tester Display
   Operation Enable Signal

   Is [Permit] displayed?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

INSPECT THE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2021 - ]

If no fault is found in the main body ECU (multiplex network body ECU), replace the power window regulator motor assembly RH.

Refer to REMOVAL [11/2021 - ]

Result: 

A 

See step  11

1. Turn the ignition switch to OFF.
2. Disconnect the power window regulator switch assembly connector.
3. Perform the inspection of power window regulator switch assembly.

   Refer to INSPECTION [11/2021 - ]

   Is the check result OK?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

REPLACE THE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to  REMOVAL [11/2021 - ] 

Result: 

A 

See step  12

1. Using a tester, measure the resistance between power window regulator switch assembly connector and power window regulator motor assembly RH connector.

   Connector & terminal

   H3-5 - H5-6

   H3-6 - H5-8

   Is the resistance less than 1 Ω?

   Result	Proceed to
   YES	A
   NO	B

Result: 

B 

REPAIR THE HARNESS 

Repair the open circuit of the harness between power window regulator switch assembly connector and power window regulator motor assembly RH connector.

Result: 

A 

See step  13

1. Turn the ignition switch to ON.
2. Using a tester, measure the voltage between the power window regulator switch assembly connector and chassis ground.

   Connector & terminal

   H3-5 - Chassis ground

   H3-6 - Chassis ground

   Is the voltage less than 1 V?

   Result	Proceed to
   YES	A
   NO	B

Result: 

A 

REPLACE THE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH. Refer to  REMOVAL [11/2021 - ] 

Result: 

B 

REPAIR THE HARNESS 

Repair the short circuit to power supply in the harness between power window regulator switch assembly connector and power window regulator motor assembly RH connector.