Data List / Active Test [03/2023 - ]
WARNING: This page is about a different variant/trim than selected.
- DATA LIST NOTE:
- Some Data List values may vary significantly if there are slight differences in the environment in which the vehicle is operating when measurements are obtained. Variations may also occur due to aging of the vehicle. Due to these considerations, it is not always possible to provide definite values to be used for judgment of malfunctions. It is possible that a malfunction may be present even if measured values are within the reference range.
- In the event of a problem with intricate symptoms, collect sample data from another vehicle of the same model operating under identical conditions in order to reach an overall judgment by comparing all the items in the Data List.
- Using the GTS, enter the following menus: Powertrain / Plug-in Control / Data List.
- Check the results by referring to the following table.
HINT:
- When reviewing Data List information, try to select only the specific Data List items related to the inspection being performed. If all items are selected when checking the Data List, the interval between updates for each item will be longer, resulting in delayed or incorrect data.
- The table below includes hidden items according to the vehicle specifications.
Powertrain > Plug-in Control > Data List
Tester Display Measurement Item Diagnostic Note Vehicle Speed Vehicle speed - Engine Speed Engine speed - Calculate Load Calculate load Value increases in proportion to increase in load - Throttle valve status
- Air cleaner condition
Coolant Temperature Engine coolant temperature - Engine Run Time Elapsed time after starting engine Elapsed time from initial engine start until the ignition switch is turned off. Throttle Position Sensor No. 1 Voltage % Accelerator pedal position sensor No. 1 - Smoothed Value of BATT Voltage Smoothed value of auxiliary battery voltage Hybrid vehicle control ECU Warmup Cycle Cleared DTC The number of times the engine is warmed up after clearing DTCs - Distance from DTC Cleared Drive distance after clearing DTCs - Time after DTC Cleared Elapsed time after clearing DTCs Time elapsed after DTCs are cleared (Not counted when the ignition switch is off). MIL MIL status - Running Time from MIL ON Running time from MIL on - Total Distance Traveled Drive total distance - Total Distance Traveled - Unit Drive total distance unit - MIL ON Run Distance Drive distance from MIL on - Number of Emission DTC Emissions-related DTCs - PISW Status AC Charging gun connecting status - My Room Operation Displays whether My-room Mode can be operated - My Room Use History Displays the My-room Mode operation history - ACRL Drive Request AC charging equipment (stand) drive request - Frequency Switching Signal Frequency signal IGB Signal IGB power source status - IGB ON Request IGB power source on request - IGCT Signal Status IGCT signal status IGCT terminal IGCT Keeping Request ON: While plug-in charging - IG2 Signal Status Status of whether IGSW is pressed
ON: IGSW ON- Charging Control Signal Status Displays CPLT signal reception status - A/C Useable Power Displays Air Conditioning System useable electric power - A/C Consumption Power Displays Air Conditioning System consumption electric power - Remote Air Control System Displays whether remote air conditioning system can be operated - Remote e Air Control Use History Displays the remote air conditioning operation history - Hybrid/EV Control System Control Mode Vehicle status controlled by EV control ECU - Hybrid/EV Output Temperature Sensor VCHG-DC/DC converter temperature - Solar Available Information Whether the solar charging can operate - Solar Diagnosis Prohibition Notification Whether the DTCs related to Solar Charging System can be detected - Solar Charging Control Mode Solar charging operation status
ON: Solar charging- Solar Charging Permission Signal by Main CPU Whether the solar charging can operate
OK: Solar charging- Solar Charging Boosting DC/DC Converter Voltage Charging voltage during solar charging operate - Solar Charging Boosting DC/DC Converter Input Power Charging power during solar charging operate - Solar Boosting DC/DC Converter Drive Request DC/DC converter for solar charging drive request
ON: Solar charging- HV/EV Battery Total Voltage Total voltage of all HV battery stacks - Hybrid/EV Battery Total Voltage at Charging Start Total voltage of all HV battery stacks when plug-in charging start - Charging Voltage for Hybrid/EV Battery Charging voltage of HV battery (VCHG value)
0.0 to 250.0 V: AC charging- Hybrid/EV Battery Local Bus Communication Battery local bus communication status
OK: HV/EV battery local bus communication permission- Hybrid/EV Battery SOC (DC Charger Display) HV battery SOC value displayed on the DC charging stand during DC charging - Hybrid/EV Battery Temperature when Charging Start HV Battery temperature when plug-in charging start - Hybrid/EV Battery Maximum Temperature HV battery highest temperature during current trip - Hybrid/EV Battery Maximum Temperature during Charging HV battery highest temperature during plug-in charging - Hybrid/EV Battery Minimum Temperature HV battery lowest temperature during current trip - Hybrid/EV Battery Minimum Temperature during Charging HV battery lowest temperature during plug-in charging - Hybrid/EV Battery Charging/Power Feeding Permission Status with Hybrid/EV Battery Thermal Keep Plug-in charging/power feeding status during HV battery cooling operated - Hybrid/EV Battery Charging Power Displays charging power of HV battery - Hybrid/EV Battery Control Status on Thermal Keeping and Charging HV battery thermal keeping control status - Hybrid/EV Battery Current for Driving Control Displays current of HV battery used for driving control - Hybrid/EV Battery Current for Hybrid/EV Battery Control Displays current of HV battery during plug-in charging - Hybrid/EV Battery Temperature Rising History Operating history of HV battery warming function - Hybrid/EV Battery Cooling History Operating history of HV battery cooling function - Auxiliary Battery Voltage Low Status Auxiliary battery voltage low status detected by plugin charge control ECU - Auxiliary Battery Voltage Low Status from Hybrid/EV Auxiliary battery voltage low status detected by HV control ECU - Auxiliary Battery Voltage Low Status from Hybrid/EV Battery Auxiliary battery voltage low status detected by battery control ECU - Hybrid/EV Communication Enable Information (Hybrid/EV Battery Local Bus) Communication condition with HV control ECU on the battery local bus - SOC of Immediately after Wake Up SOC (State of Charge) (All Bat) at the start of charging - ICHG Current (Instantaneous Value) Current flowing from the electric vehicle charger assembly to the HV battery or from the HV battery to the electric vehicle charger assembly - Charging Lid Switch Status Charging lid switch status
ON: Normal charging port lid open- Charging Lid Lamp Status Charging lid light status - Hood Courtesy Switch Signal Hood open/close status - Charging Indicator lighting Request Charging indicator illumination request
ON: When there is a charging indicator illumination request- Charging Connector Connect Status AC charging connector connection state - Charging Connector Connect Status Voltage PISW terminal voltage used for checking electric vehicle charger cable assembly connection condition - 0.35 to 2.02 V: Electric vehicle charger cable assembly connected
- 2.02 to 3.57 V: Electric vehicle charger cable assembly inserted and the latch release button (PI switch) engaged
- 3.57 to 4.73 V: Electric vehicle charger cable assembly not inserted
PISW terminal voltage Charging Connector Lock Pin Status Charging connector lock pin status - Charging Connector Lock Motor Unlock Direction Revolution Request Current Output of current to operate charging connector lock motor in reverse
ON: Unlocking Charging connector (operating charging connector lock motor in reverse)- Charging Connector Lock Motor Lock Direction Revolution Request Current Output of current to operate charging connector lock motor forward
ON: Locking Charging connector (operating charging connector lock motor forward)- Connector Unlock History during Charging Charging connector unlock history during plug-in charging Cannot be used AC Charging Positive Inlet Temperature Sensor Voltage Voltage value for temperature sensor of inlet AC Charging (Positive side) - AC Charging Negative Inlet Temperature Sensor Voltage Voltage value for temperature sensor of inlet AC Charging (Negative side) - AC Charging Positive Inlet Temperature Temperature of inlet AC Charging (Positive side) - AC Charging Negative Inlet Temperature Temperature of inlet AC Charging (Negative side) - AC Charging Inlet Insert Status Device connection status to the AC charging inlet and its availability - Power Feeding Connecter Power Supply Switch Status of supply power source connector - Interlock Operation Status Interlock operation status - Charger Power Supply Voltage Type Plug-in charging power source voltage - Charger Operation Status Charging operation state Charging operation state signal (CHST) Charger Operation Request Charging operation request state Charging operation request signal (CHRQ) Charger Input Power Power input to electric vehicle charger assembly from AC charging inlet - Charger Output Power Power output from electric vehicle charger assembly - Charger Cooling Fan Drive Request Charger cooling blower drive request Cannot be used Charger Cooling Fan Driving Duty Charger cooling blower operation duty ratio - Charger Cooling Fan Revolution Charger cooling blower speed - Charger Drive Permission Signal Drive permission status of electric vehicle charger assembly - AC Power Supply Rated Current Rated current when AC charging performed - AC Power Supply Rated Power Rated power when AC charging performed - Minimum Cable Permission Current during Charging Charging cable permission current minimum value recorded during AC charging - Charging Control Information HV battery thermal keeping function status during plug-in charging - Charging History Information Charging end factor - DC Operation Mode DC charging operation mode - 6A Charging Mode Switching History History of switched to 6A charging mode on latest AC charging - DTC Detection History DTC detection history while current plug-in charging - Record on Behavior Detection History RoB detection history while current plug-in charging - System Impedance Increase Abnormal Displays AC charging system impedance increase - Minimum Charging Permission Power during Charging The value closest to 0 in charging permission power limited by battery condition during plug-in charging - This item approximately negative value during plug-in charging.
- The larger the absolute value, the higher the charging capacity.
Maximum Charging Current Setting (200V) Maximum charging current for AC charging set by the customer for 200 V mode Total Number of AC Charging Cumulative plug-in charging operations - AC Charging Total Time Cumulative plug-in charging time - AC Charging Plug-in AC charging availability - AC Charging Operation Status Plug-in AC charging operation status - AC Charging Input Minimum Voltage History Minimum voltage during plug-in AC charging - AC Input Voltage for Monitoring before Charging AC charging device output voltage (before start AC charging) - Target Charging Power Charging power target value Charging power output request signal (CHPW) Target Charging Power from Charger Charging power target value output from electric vehicle charger assembly - Charging Required Time Calculation Status Charging time required calculation complete/incomplete flag - Charging Required Time Calculated charging time required to complete charging - Charging Elapsed Time Time elapsed since plug-in charging started - Charging State Elapsed Time Elapsed time since the transition from each control state of AC charging - AC Input Voltage for Monitoring Effective AC voltage input to electric vehicle charger assembly from inlet AC charger cable (charging inlet) VIN voltage Target AC Input Voltage for Control Target voltage value to be output when supplying power - AC Input Voltage Instantaneous Value 1 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 1 - AC Input Voltage Instantaneous Value 2 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 2 - AC Input Voltage Instantaneous Value 3 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 3 - AC Input Voltage Instantaneous Value 4 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 4 - AC Input Voltage Instantaneous Value 5 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 5 - AC Input Voltage Instantaneous Value 6 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 6 - AC Input Voltage Instantaneous Value 7 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 7 - AC Input Voltage Instantaneous Value 8 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 8 - AC Input Voltage Instantaneous Value 9 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 9 - AC Input Voltage Instantaneous Value 10 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 10 - AC Input Voltage Instantaneous Value 11 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 11 - AC Input Voltage Instantaneous Value 12 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 12 - AC Input Voltage Instantaneous Value 13 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 13 - AC Input Voltage Instantaneous Value 14 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 14 - AC Input Voltage Instantaneous Value 15 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 15 - AC Input Voltage Instantaneous Value 16 for Waveform Monitoring VIN sensor waveform voltage (instantaneous value) 16 - Time Cycle of Charging Voltage Zero Crossing Point AC input voltage zero cross cycle - Plug-in Control ECU Voltage Request (SMP5) Internal power source voltage (SMP5) request value - Plug-in Control ECU Voltage (VOMS5) Internal power source voltage (VOMS5) - Plug-in Control Module System Voltage (Plus) Plugin charge control ECU internal power source voltage - Plug-in Control Module System Voltage (Minus) Plugin charge control ECU internal power source voltage - AC Power Feeding Control Mode AC external supply power control status - AC Input Current IAC effective value IAC current Charging Current Upper Limit Maximum supply current - Charging Voltage (Average Effective Value) Average value of supply voltage effective value - Charging Voltage (Trip Crest Value) Maximum value of supply voltage instantaneous value - Charging Current Duty from Charger Duty value of charging voltage judgment recognition signal (CPLT)
0%: Not connected to the EVSE (charging station) system or power unavailable
3% or more and 7% or less: A charging connector is connected- Allowable amperage from EVSE (charging station) can be determined based on CPLT duty. (Allowable amperage [A] = CPLT duty value x 0.6)
- The electric vehicle charger assembly limits the amperage based on CPLT duty value.
Time Cycle of Charging Current Duty from Charger Duration of 1 cycle of CPLT
0 μs: Not connected to an EVSE (charging station) system or power unavailable
951 to 1049 μs: CPLT (control pilot signal) generatedCycle of the CPLT pulse corresponding to the CPLT duty Charging Current Limit Status from Charger Existence of charging current restriction ILMT: Charging current restriction value Charging Power Limit (Charging Voltage Low) Charging power limit (throttling control) - Timer Wait Request Waiting status due to timer charging - Timer Setting Latest timer charging setting status - Power Supply Voltage (SMP5) SMP5 power source voltage value - PFC Boosting Circuit Driver Drive Status PFC booster circuit drive control operation state - Voltage after Boosting by PFC Boosting Circuit Voltage value after boosting by PFC boosting circuit - PFC Boosting Circuit Current Amplitude PFC booster circuit maximum current - PFC Temperature Temperature around PFC booster circuit - High Voltage Circuit Shutdown Signal High voltage circuit shutdown status - DC/DC Converter Operation Status Main DC/DC converter operation status - DC/DC Converter Driver Drive Status (for Charging) DC/DC converter (for charging HV battery) drive control operating state - DC/DC Converter Temperature (for Charging) Main DC/DC converter (for charging HV battery) temperature - AC 100V Switch Indicator Lighting Request AC 100 V switch indicator illumination request
ON: Request exists- Power Feeding Isolation Fault Detection Status of whether an electrical leak is detected - Power Feeding Inverter Operation Status Operation status of the supply power inverter - Power Feeding INV Activate Request Supply power inverter operation request - Power Feeding INV Activate Status Status of supply power operation - Power Feeding INV Output Frequency Setting Set value of supply power output frequency - Power Feeding INV Output Voltage Setting Set value of supply power output voltage - Charging/Power Feeding Switching Switch Status Switching status between charge mode and supply mode
OFF: Charging system side
ON: Interior power outlet side- Charging/Power Feeding Switching Switch Request Request to switch between charge mode and supply mode
OFF: Charging system side
ON: Interior power outlet side- AC Charging Negative Relay Status Operating state of CHRG
ON: CHRG relay connected- AC Charging Positive Relay Status Operating state of CHRB
ON: CHRB relay connected- AC Charging Negative Relay Drive Request Commanded state of CHRG
ON: CHRG relay connection being commanded- AC Charging Positive Relay Drive Request Commanded state of CHRB
ON: CHRB relay connection being commanded- AC Charging Precharge Relay Status Operating state of CHRP
ON: CHRP relay connected- AC Charging Precharge Relay Drive Request Commanded state of CHRP
ON: CHRP relay connection being commanded- Charging Relay Connect Request in CCID Box from CCID Box CCID (charging circuit interrupt device) relay state request signal - Rush Current Prevention Resistance Relay Activate Request Inrush current protection relay operation request signal - SMRB Control Status Commanded state of SMRB - SMRG Control Status Commanded state of SMRG - VAI Whether VAI system exists - VAO Whether VAO system exists - +B Voltage AM21 power source voltage value -