LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2025 >> Sequoia TRD Pro >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> Engine Control System - Service Information >> Camshaft Position Sensor >> Removal [09/2022 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Removal [09/2022 - ]: Procedure

  1. REMOVE V-BANK COVER SUB-ASSEMBLY 

    See step  1

  2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY 

    Refer to REMOVAL [09/2022 - ]

  3. REMOVE COWL TOP PANEL SUB-ASSEMBLY OUTER 

    Refer to PROCEDURE - Step 22

  4. REMOVE CAMSHAFT POSITION SENSOR (for Intake Side of Bank 1) 
    1. GTY1091423Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the camshaft position sensor (for Intake Side of Bank 1) connector.
      2. Remove the bolt and camshaft position sensor (for Intake Side of Bank 1) from the cylinder head cover sub-assembly.
        NOTE:

        If the camshaft position sensor (for Intake Side of Bank 1) has been struck or dropped, replace it.

      3. Perform this procedure only when reusing the camshaft position sensor (for Intake Side of Bank 1).

        1. Remove the O-ring from the camshaft position sensor (for Intake Side of Bank 1).

        NOTE:
        • Make sure to only remove the O-ring with bare hands.
        • When removing the O-ring, be careful not to damage the O-ring groove of the camshaft position sensor (for Intake Side of Bank 1).
        • If the O-ring groove of the camshaft position sensor (for Intake Side of Bank 1) is damaged, replace the camshaft position sensor (for Intake Side of Bank 1) with a new one.
  5. REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 1) 
    1. GTY1096990Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the camshaft position sensor (for Exhaust Side of Bank 1) connector.
      2. Remove the bolt and camshaft position sensor (for Exhaust Side of Bank 1) from the cylinder head cover sub-assembly.
        NOTE:

        If the camshaft position sensor (for Exhaust Side of Bank 1) has been struck or dropped, replace it.

      3. Perform this procedure only when reusing the camshaft position sensor (for Exhaust Side of Bank 1).

        1. Remove the O-ring from the camshaft position sensor (for Exhaust Side of Bank 1).

        NOTE:
        • Make sure to only remove the O-ring with bare hands.
        • When removing the O-ring, be careful not to damage the O-ring groove of the camshaft position sensor (for Exhaust Side of Bank 1).
        • If the O-ring groove of the camshaft position sensor (for Exhaust Side of Bank 1) is damaged, replace the camshaft position sensor (for Exhaust Side of Bank 1) with a new one.
  6. REMOVE CAMSHAFT POSITION SENSOR (for Intake Side of Bank 2) 
    1. GTY1095810Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the camshaft position sensor (for Intake Side of Bank 2) connector.
      2. Remove the bolt and camshaft position sensor (for Intake Side of Bank 2) from the cylinder head cover sub-assembly.
        NOTE:

        If the camshaft position sensor (for Intake Side of Bank 2) has been struck or dropped, replace it.

      3. Perform this procedure only when reusing the camshaft position sensor (for Intake Side of Bank 2).

        1. Remove the O-ring from the camshaft position sensor (for Intake Side of Bank 2).

        NOTE:
        • Make sure to only remove the O-ring with bare hands.
        • When removing the O-ring, be careful not to damage the O-ring groove of the camshaft position sensor (for Intake Side of Bank 2).
        • If the O-ring groove of the camshaft position sensor (for Intake Side of Bank 2) is damaged, replace the camshaft position sensor (for Intake Side of Bank 2) with a new one.
  7. REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 2) 
    1. GTY1093924Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the camshaft position sensor (for Exhaust Side of Bank 2) connector.
      2. Remove the bolt and camshaft position sensor (for Exhaust Side of Bank 2) from the cylinder head cover sub-assembly.
        NOTE:

        If the camshaft position sensor (for Exhaust Side of Bank 2) has been struck or dropped, replace it.

      3. Perform this procedure only when reusing the camshaft position sensor (for Exhaust Side of Bank 2).

        1. Remove the O-ring from the camshaft position sensor (for Exhaust Side of Bank 2).

        NOTE:
        • Make sure to only remove the O-ring with bare hands.
        • When removing the O-ring, be careful not to damage the O-ring groove of the camshaft position sensor (for Exhaust Side of Bank 2).
        • If the O-ring groove of the camshaft position sensor (for Exhaust Side of Bank 2) is damaged, replace the camshaft position sensor (for Exhaust Side of Bank 2) with a new one.
scientia non olet · About LEMON Manuals