4.2L V8 5V Generic Scan Tool, Engine Code(S): BGH, BGJ
- 20 Fuel Supply
- Fuel supply system components, removing and installing
- Fuel supply system components, removing and installing
- Fuel tank with attachments and fuel filter, disassembling and assembling
- Fuel Pump (FP) unit, sender for fuel gauge and suction jet pump (right side), disassembling and assembling
- Fuel Pump (FP) unit, sender for fuel gauge and suction jet pump (left side), disassembling and assembling
- Connection diagram for fuel lines and fuel tank components
- Safety precautions when working on fuel supply system
- Rules of cleanliness
- Fuel tank, emptying
- Fuel Pump (FP) unit, sender for fuel gauge and suction jet pump (right side), removing and installing
- Fuel Pump (FP) unit, sender for fuel gauge and suction jet pump (left side), removing and installing
- Fuel Pumps (FP), checking
- Notes
- Check function and voltage supply of fuel pumps
- Test sequence, Transfer Fuel Pump (FP) -G23-, right
- Test sequence, Fuel Pump (FP) -G6-, left
- Check delivery quantity, current pick-up, and check-valves of Fuel Pumps (FP)
- Checking fuel delivery
- Delivery quantity of Transfer Fuel Pump (FP) -G23-, right, checking
- Delivery quantity of Fuel Pump (FP) -G6-, left, checking
- Check current pick-up of Fuel Pumps (FP)
- Checking check-valves of Fuel Pumps (FP)
- Test sequence
- Check-valve of Transfer Fuel Pump (FP) -G23-, right, checking
- Check-valve of Fuel Pump (FP) -G6-, left, checking
- EVAP canister system
- Function of leak diagnostic
- EVAP canister system components, removing and installing
- Evaporative Emission (EVAP) canister system, checking for proper seal
- Evaporative Emission (EVAP) canister purge regulator valve 1, checking
- Leak Detection Pump (LDP), checking
- EVAP system, checking using KLI 9210 tester
- Electronic engine power control (EPC)
- Fuel supply system components, removing and installing
- 24 Multiport Fuel Injection (MFI)
- Fuel injection, servicing
- Engine components, checking
- Oxygen sensor heater for oxygen sensors before catalytic converter, checking
- Oxygen sensor heater for oxygen sensors behind Three Way Catalytic Converter (TWC), checking
- Mass Air Flow (MAF) sensor, checking
- Throttle valve control module, checking
- Engine Coolant Temperature (ECT) sensor, checking
- Intake Air Temperature (IAT) sensor, checking
- Engine speed (RPM) sensor, checking
- Engine Coolant Temperature (ECT) Sensor (on Radiator), checking
- Coolant FC (Fan Control) Control Module 1, checking
- Coolant FC (Fan Control) Control Module 2, checking
- Coolant pump, checking
- Fuel injectors, checking
- Fuel pressure regulator and residual pressure, checking
- Intake system, checking for leaks (false air)
- Function tests
- Engine Control Module (ECM)
- Additional signals, checking
- 26 Exhaust system, Emission controls
- Exhaust system components, removing and installing
- Secondary Air Injection (AIR) system
- Secondary Air Injection (AIR) system
- Function
- Secondary Air Injection (AIR) system components, removing and installing
- Secondary Air Injection (AIR) pump motor, removing and installing
- Secondary Air Injection (AIR) system, checking for proper seal
- Secondary Air Injection (AIR) valve, checking
- Secondary Air Injection (AIR) pump motor, checking
- Combination valves, checking
- 28 Ignition/Glow plug system
- Ignition, servicing
- General notes on ignition system
- Ignition components, removing and installing
- Safety precautions
- Test Data, Spark Plugs
- Ignition coils with power output stage, removing and installing
- Ignition coils with power output stages, checking
- Camshaft Position (CMP) sensor, checking
- Knock sensors, checking
- Camshaft adjustment valves, checking
- Ignition, servicing
- 38 Automatic Transmission - Gears, Hydraulic controls
- ST Generic Scan Tool
- General information for On Board Diagnostic (OBD)
- Diagnostic mode, selecting
- Diagnostic mode, selecting
- Address word 33 - On-Board Diagnostics (OBD)
- Diagnostic mode 1: Check measured values
- Diagnostic mode 2: Check operating conditions
- Diagnostic mode 3: Check DTC Memory
- Diagnostic mode 4: Reset/erase diagnostic data
- Diagnostic mode 5: Check output of oxygen sensor signals
- Notes
- Evaluation test-ID 07 Bank 1 and 2, sensor 2: Minimum voltage at sensor for test cycle
- Evaluation test-ID 08 Bank 1 and 2, sensor 2: Maximum voltage at sensor for test cycle
- Evaluation test-ID 129 Bank 1 and 2, sensor 1: Oxygen sensor value
- Evaluation test-ID 130 Bank 1 and 2, sensor 1: Control barrier value
- Evaluation test-ID 131 Bank 1 and 2, sensor 1: Dynamic value
- Diagnostic mode 6: Check test results of components that are not continuously monitored
- Diagnostic mode 7: Check test results of components that are continuously monitored
- Diagnostic mode 8: Tank leak test
- Diagnostic mode 9: Vehicle information
- Readiness code
- DTC tables