| C00A1:57 |
Driveline Control Module: Invalid / Incompatible Software Component |
GO to Pinpoint Test C |
| C00A1:F1 |
Driveline Control Module: <Manufacturer Defined> |
GO to Pinpoint Test C |
| C05D8:01 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: General electrical failure |
GO to Pinpoint Test D |
| C05D8:08 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Bus Signal / Message Failure |
GO to Pinpoint Test D |
| C05D8:19 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Circuit Current Above Threshold |
GO to Pinpoint Test D |
| C05D8:49 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Internal Electronic Failure |
GO to Pinpoint Test D |
| C05D8:4B |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Over temperature |
GO to Pinpoint Test D |
| C05D8:96 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Component Internal Failure |
GO to Pinpoint Test D |
| C05D9:18 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Circuit Current Below Threshold |
GO to Pinpoint Test D |
| C05D9:19 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Circuit Current Above Threshold |
GO to Pinpoint Test D |
| C05D9:44 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Data Memory Failure |
GO to Pinpoint Test D |
| C05D9:44 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Data Memory Failure |
GO to Pinpoint Test U |
| C05D9:74 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Actuator Slipping |
GO to Pinpoint Test D |
| C05D9:99 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Exceeded Learning Limit |
GO to Pinpoint Test D |
| C05E0:1C |
4WD/AWD Clutch "A" Position Sensor Circuit: Circuit Voltage Out of Range |
GO to Pinpoint Test E |
| C05E0:86 |
4WD/AWD Clutch "A" Position Sensor Circuit: Signal Invalid |
GO to Pinpoint Test E |
| P0562:00 |
System Voltage |
GO to Pinpoint Test C |
| P0563:00 |
System Voltage high |
GO to Pinpoint Test C |
| P0603:00 |
Internal Control Module Keep Alive Memory (KAM) Error |
GO to Pinpoint Test C |
| P0604:00 |
Internal Control Module Random Access Memory (RAM) Error |
GO to Pinpoint Test C |
| P0605:00 |
Internal Control Module Read Only Memory (ROM) Error |
GO to Pinpoint Test C |
| P0607:00 |
Control Module Performance |
GO to Pinpoint Test C |
| P060A:00 |
Internal Control Module Monitoring Processor Performance |
GO to Pinpoint Test C |
| P060B:00 |
Internal Control Module A/D Processing Performance |
GO to Pinpoint Test C |
| P060C:00 |
Internal Control Module Main Processor Performance |
GO to Pinpoint Test C |
| P0630:00 |
VIN Not Programmed or Incompatible - ECM/PCM |
GO to Pinpoint Test B |
| P064F:00 |
Unauthorized Software/Calibration Detected |
GO to Pinpoint Test C |
| P068A:00 |
ECM/PCM Power Relay De-Energized - Too Early |
GO to Pinpoint Test C |
| P1001:00 |
KOER Not Able to Complete, KOER Aborted |
GO to Pinpoint Test A |
| P1397:01 |
System Voltage Out Of Self-Test Range: General Electrical Failure |
GO to Pinpoint Test A |
| P1501:00 |
Vehicle Speed Sensor Out Of Self Test Range |
GO to Pinpoint Test A |
| P160A:00 |
Control Module Vehicle Options Reconfiguration Error |
GO to Pinpoint Test B |
| P166E:00 |
Internal control module all wheel drive disconnect control performance |
GO to Pinpoint Test C |
| P1674:00 |
Control Module Software Corrupted |
GO to Pinpoint Test C |
| P1705:00 |
Transmission Range Circuit Not Indicating Park/Neutral During Self-Test |
GO to Pinpoint Test A |
| P184A:00 |
Transfer Case Unable To Transition Between 4x2 and 4x4 Mode |
GO to Pinpoint Test D |
| P184C:00 |
Transfer Case Transition Time Range/Performance |
GO to Pinpoint Test D |
| U0100:00 |
Lost Communication With ECM/PCM "A" |
GO to Pinpoint Test F |
| U0101:00 |
Lost Communication with TCM |
GO to Pinpoint Test F |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module "A" |
GO to Pinpoint Test F |
| U0126:00 |
Lost Communication With Steering Angle Sensor Module |
GO to Pinpoint Test F |
| U0137:00 |
Lost Communication With Trailer Brake Control Module |
GO to Pinpoint Test F |
| U0138:00 |
Lost Communication with All Terrain Control Module |
GO to Pinpoint Test F |
| U0140:00 |
Lost Communication With Body Control Module |
GO to Pinpoint Test F |
| U0146:00 |
Lost Communication With Serial Data Gateway "A" |
GO to Pinpoint Test F |
| U0151:00 |
Lost Communication With Restraints Control Module |
GO to Pinpoint Test F |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module |
GO to Pinpoint Test F |
| U0164:00 |
Lost Communication With HVAC Control Module |
GO to Pinpoint Test F |
| U0212:00 |
Lost Communication With Steering Column Control Module |
GO to Pinpoint Test F |
| U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A" |
GO to Pinpoint Test G |
| U0422:00 |
Invalid Data Received From Body Control Module |
GO to Pinpoint Test G |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module |
GO to Pinpoint Test G |
| U0428:00 |
Invalid Data Received From Steering Angle Sensor Module |
GO to Pinpoint Test G |
| U1011:00 |
Invalid Internal Control Module Monitoring Data Received from ECM/PCM |
GO to Pinpoint Test G |
| U1012:00 |
Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module |
GO to Pinpoint Test G |
| U1014:00 |
Invalid Internal Control Module Monitoring Data Received from Restraints Control Module |
GO to Pinpoint Test G |
| U2100:00 |
Initial Configuration Not Complete |
GO to Pinpoint Test B |
| U2101:00 |
Control Module Configuration Incompatible |
GO to Pinpoint Test B |
| U2200:00 |
Control Module Configuration Memory Corrupt |
GO to Pinpoint Test B |