| C00A1:57 |
Driveline Control Module: Invalid / Incompatible Software Component |
GO to Pinpoint Test C |
| C00A1:F1 |
Driveline Control Module: <Manufacturer Defined> |
GO to Pinpoint Test C |
| C05D8:01 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: General electrical failure |
GO to Pinpoint Test D |
| C05D8:08 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Bus Signal / Message Failure |
GO to Pinpoint Test D |
| C05D8:19 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Circuit Current Above Threshold |
GO to Pinpoint Test D |
| C05D8:49 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Internal Electronic Failure |
GO to Pinpoint Test D |
| C05D8:4B |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Over temperature |
GO to Pinpoint Test D |
| C05D8:96 |
4WD/AWD Clutch "A" Actuator Control Circuit/Open: Component Internal Failure |
GO to Pinpoint Test D |
| C05D9:18 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Circuit Current Below Threshold |
GO to Pinpoint Test D |
| C05D9:19 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Circuit Current Above Threshold |
GO to Pinpoint Test D |
| C05D9:44 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Data Memory Failure |
GO to Pinpoint Test D |
| C05D9:44 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Data Memory Failure |
GO to Pinpoint Test J |
| C05D9:74 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Actuator Slipping |
GO to Pinpoint Test D |
| C05D9:99 |
4WD/AWD Clutch "A" Actuator Control Circuit Performance: Exceeded Learning Limit |
GO to Pinpoint Test D |
| C05E0:1C |
4WD/AWD Clutch "A" Position Sensor Circuit: Circuit Voltage Out of Range |
GO to Pinpoint Test E |
| C05E0:86 |
4WD/AWD Clutch "A" Position Sensor Circuit: Signal Invalid |
GO to Pinpoint Test E |
| C0688:09 |
4WD/AWD Clutch "A" Brake Actuator: Component Failure |
GO to Pinpoint Test L |
| C0688:11 |
4WD/AWD Clutch "A" Brake Actuator: Circuit Short To Ground |
GO to Pinpoint Test L |
| C0688:12 |
4WD/AWD Clutch "A" Brake Actuator: Circuit Short To Battery |
GO to Pinpoint Test L |
| C0688:19 |
4WD/AWD Clutch "A" Brake Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test L |
| C0688:1D |
4WD/AWD Clutch "A" Brake Actuator: Circuit Current Out of Range |
GO to Pinpoint Test L |
| C0688:72 |
4WD/AWD Clutch "A" Brake Actuator: Actuator Stuck Open |
GO to Pinpoint Test L |
| C0688:74 |
4WD/AWD Clutch "A" Brake Actuator: Actuator Slipping |
GO to Pinpoint Test L |
| C0688:A2 |
4WD/AWD Clutch "A" Brake Actuator: System Voltage Low |
GO to Pinpoint Test L |
| C0689:11 |
4WD/AWD Clutch "A" Actuator Position Sensor "A": Circuit Short To Ground |
GO to Pinpoint Test E |
| C0689:13 |
4WD/AWD Clutch "A" Actuator Position Sensor "A": Circuit Open |
GO to Pinpoint Test E |
| C0689:17 |
4WD/AWD Clutch "A" Actuator Position Sensor "A": Circuit Voltage Above Threshold |
GO to Pinpoint Test E |
| C0689:29 |
4WD/AWD Clutch "A" Actuator Position Sensor "A": Signal invalid |
GO to Pinpoint Test E |
| C0689:29 |
4WD/AWD Clutch "A" Actuator Position Sensor "A": Signal invalid |
GO to Pinpoint Test E |
| C068A:11 |
4WD/AWD Clutch "A" Actuator Position Sensor "B": Circuit Short To Ground |
GO to Pinpoint Test E |
| C068A:13 |
4WD/AWD Clutch "A" Actuator Position Sensor "B": Circuit Open |
GO to Pinpoint Test E |
| C068A:17 |
4WD/AWD Clutch "A" Actuator Position Sensor "B": Circuit Voltage Above Threshold |
GO to Pinpoint Test E |
| C068A:29 |
4WD/AWD Clutch "A" Actuator Position Sensor "B": Signal invalid |
GO to Pinpoint Test E |
| C068A:29 |
4WD/AWD Clutch "A" Actuator Position Sensor "B": Signal invalid |
GO to Pinpoint Test E |
| C068F:17 |
4WD/AWD Clutch "A" Actuator Range Sensor: Circuit Voltage Above Threshold |
GO to Pinpoint Test K |
| C068F:34 |
4WD/AWD Clutch "A" Actuator Range Sensor: Signal High Time less than Minimum |
GO to Pinpoint Test K |
| C068F:35 |
4WD/AWD Clutch "A" Actuator Range Sensor: Signal High Time greater than Maximum |
GO to Pinpoint Test K |
| C068F:36 |
4WD/AWD Clutch "A" Actuator Range Sensor: Signal Frequency Too Low |
GO to Pinpoint Test K |
| C068F:37 |
4WD/AWD Clutch "A" Actuator Range Sensor: Signal Frequency Too High |
GO to Pinpoint Test K |
| C068F:49 |
4WD/AWD Clutch "A" Actuator Range Sensor: Internal Electronic Failure |
GO to Pinpoint Test K |
| C068F:86 |
4WD/AWD Clutch "A" Actuator Range Sensor: Signal Invalid |
GO to Pinpoint Test K |
| C068F:94 |
4WD/AWD Clutch "A" Actuator Range Sensor: Unexpected Operation |
GO to Pinpoint Test K |
| C068F:96 |
4WD/AWD Clutch "A" Actuator Range Sensor: Component Internal Failure |
GO to Pinpoint Test K |
| C068F:A3 |
4WD/AWD Clutch "A" Actuator Range Sensor: System Voltage High |
GO to Pinpoint Test K |
| P0562:00 |
System Voltage Low: No Sub Type Information |
GO to Pinpoint Test C |
| P0563:00 |
System Voltage high: No Sub Type Information |
GO to Pinpoint Test C |
| P0603:00 |
Internal Control Module Keep Alive Memory (KAM) Error: No Sub Type Information |
GO to Pinpoint Test C |
| P0604:00 |
Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information |
GO to Pinpoint Test C |
| P0605:00 |
Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information |
GO to Pinpoint Test C |
| P0607:00 |
Control Module Performance: No Sub Type Information |
GO to Pinpoint Test C |
| P060A:00 |
Internal Control Module Monitoring Processor Performance: No Sub Type Information |
GO to Pinpoint Test C |
| P060B:00 |
Internal Control Module A/D Processing Performance: No Sub Type Information |
GO to Pinpoint Test C |
| P060C:00 |
Internal Control Module Main Processor Performance: No Sub Type Information |
GO to Pinpoint Test C |
| P0630:00 |
VIN Not Programmed or Incompatible - ECM/PCM: No Sub Type Information |
GO to Pinpoint Test B |
| P0641:1C |
Sensor Reference Voltage "A" Circuit/Open: Circuit Voltage Out of Range |
GO to Pinpoint Test L |
| P064F:00 |
Unauthorized Software/Calibration Detected: No Sub Type Information |
GO to Pinpoint Test C |
| P068A:00 |
ECM/PCM Power Relay De-Energized - Too Early: No Sub Type Information |
GO to Pinpoint Test C |
| P1001:00 |
KOER Not Able to Complete, KOER Aborted: No Sub Type Information |
GO to Pinpoint Test A |
| P1397:01 |
System Voltage Out Of Self-Test Range: General Electrical Failure |
GO to Pinpoint Test A |
| P1501:00 |
Vehicle Speed Sensor Out Of Self Test Range: No Sub Type Information |
GO to Pinpoint Test A |
| P160A:00 |
Control Module Vehicle Options Reconfiguration Error: No Sub Type Information |
GO to Pinpoint Test B |
| P166E:00 |
Internal control module all wheel drive discounnect control performance: No Sub Type Information |
GO to Pinpoint Test C |
| P1674:00 |
Control Module Software Corrupted: No Sub Type Information |
GO to Pinpoint Test C |
| P1705:00 |
Transmission Range Circuit Not Indicating Park/Neutral During Self-Test: No Sub Type Information |
GO to Pinpoint Test A |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test F |
| U0101:00 |
Lost Communication with TCM: No Sub Type Information |
GO to Pinpoint Test F |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test F |
| U0126:00 |
Lost Communication With Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test F |
| U0137:00 |
Lost Communication With Trailer Brake Control Module: No Sub Type Information |
GO to Pinpoint Test F |
| U0138:00 |
Lost Communication with All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test F |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test F |
| U0146:00 |
Lost Communication With Serial Data Gateway "A": No Sub Type Information |
GO to Pinpoint Test F |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test F |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test F |
| U0164:00 |
Lost Communication With HVAC Control Module: No Sub Type Information |
GO to Pinpoint Test F |
| U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test F |
| U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test G |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test G |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test G |
| U0428:00 |
Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test G |
| U1011:00 |
Invalid Internal Control Module Monitoring Data Received from ECM/PCM: No Sub Type Information |
GO to Pinpoint Test G |
| U1012:00 |
Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
GO to Pinpoint Test G |
| U1014:00 |
Invalid Internal Control Module Monitoring Data Received from Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test G |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test B |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test B |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test B |