Keyless Access System Check (2015 2017)

1. Connect the HDS to the data link connector (DLC)

2. Turn the vehicle to the ON mode.

3. On the HDS screen, at SYSTEM SELECTION MENU, enter ONE-PUSH START, then select KEYLESS ACCESS CONTROL UNIT or BACKUP CONTROL UNIT.

NOTE: If the HDS does not communicate, check the keyless access control unit power, ground, K-line, and L-line connectors.

4. At KEYLESS ACCESS CONTROL UNIT, enter KEYLESS ACCESS SYSTEM INFORMATION, then select SYSTEM CHECK 1 or SYSTEM CHECK 2.

5. At BACKUP CONTROL UNIT, enter SYSTEM INFORMATION, then select SYSTEM CHECK.

6. If the HDS displays NORMAL N-1, the immobilizer system is OK at this time, refer to the STATUS LOG. If the HDS displays any other messages, check as follows:

System Check 1 (Keyless Access Control Unit)

System Check No.	Possible cause	Check items
A-1 A-2 A-3 G-4	Keyless remote is mismatched LF interior antenna failure Keyless remote is not registered	Remote test LF interior antenna test Register the remote
B-1 B-2 G-1	PCM is replaced No communication between Keyless Access Control Unit and PCM Open in the IG1 line Keyless Access Control Unit is replaced	Register the PCM Check PCM Check harness Register the Keyless Access Control Unit
C-1 C-2 G-2 G-3	MICU (Imoes unit) is replaced Communication error between Keyless Access Control Unit and MICU Open in the IG1 line Keyless Access Control Unit is replaced	Register the Keyless Access Control Unit Check MICU Check harness
C-3 C-4	Power Control Unit is replaced Electric Steering Lock is replaced * Keyless Access Control Unit is replaced	Register the Keyless Access Control Unit Register the Electric Steering Lock * Check for an open or short in the wire IGN TRX lines *
G-5	Electric Steering Lock is replaced * Keyless Access Control Unit is replaced	Register the Keyless Access Control Unit Register the Electric Steering Lock * Check for an open or short in the wire IGN TRX lines *

*: Canada model

System Check 2 (Keyless Access Control Unit)

System Check No.	Possible cause	Check items
D-1 D-2 D-3	S-NET line is short No communication between Keyless Access Control Unit and MICU (Imoes unit) No communication between Keyless Access Control Unit and PCM	Check harness Check MICU Check PCM
D-4 D-5	IGN TRX line trouble *	Check IGN TRX line *

System Check No.

Possible cause

Check items

D-1

D-2

D-3

S-NET line is short
No communication between Keyless Access Control Unit and MICU (Imoes unit)
No communication between Keyless Access Control Unit and PCM

Check harness
Check MICU
Check PCM

D-4

D-5

IGN TRX line trouble *

Check IGN TRX line *

*: Canada model

System Check (Backup Control Unit)

System Check No.	Possible cause	Check items
A-1 A-2 A-3	Keyless remote is mismatched Power Switch failure Keyless remote is not registered	Register the remote Check Power Switch
B-1 B-2	PCM is replaced Communication error between Keyless Access Control Unit and PCM	Register the PCM Check PCM
C-1 C-2	MICU is replaced Communication error between Keyless Access Control Unit and MICU Open in the IG1 line	Register the Keyless Access Control Unit Check MICU Check harness
D-1 D-2 D-3	S-NET line is short No communication between Keyless Access Control Unit and MICU (Imoes unit) No communication between Keyless Access Control Unit and PCM	Check harness Check MICU Check PCM
E-1 E-2 E-3 E-4 E-5	Keyless Access Control Unit is not registered	Register the Keyless Access Control Unit
F-1 F-2 F-3 F-4 F-5	Special Mode	Turn the vehicle to the ON mode and then OFF (LOCK) mode with a registered remote