Keyless/Power Door Locks/Security System Symptom Troubleshooting - Security alarm system will not arm: Inspection

HOOD_SW, GND Circuit Inspection 

Test Procedure 

• Preparation
  1. -

     Hood latch switch connector (2P): disconnected

  2. -

     Relay control module connector C (18P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected)Hood latch switch connector (2P) female terminals	(Disconnected)Relay control module connector C (18P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	HOOD_SW open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.

HOOD_SW shorted to ground inspection

OFF

There is more than 1 MOhm

Results 

• If abnormal, there is a problem in the circuit.

FL_DOOR_SW, GND Open Wire Inspection 

Test Procedure 

• Preparation
  1. -

     Driver's door latch connector (10P): disconnected

  2. -

     Body control module connector B (66P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Driver's door latch connector (10P) female terminals	(Disconnected)Body control module connector B (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	FL_DOOR_SW open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm

Results 

• If abnormal, there is a problem in the circuit.

DR_SILCON_UNLOCK, GND Circuit Inspection 

Test Procedure 

• Preparation
  1. -

     Driver's door latch connector (10P): disconnected

  2. -

     Power window master switch 37P connector: disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Driver's door latch connector (10P) female terminals	(Disconnected)Power window master switch 37P connector female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	DR_SILCON_UNLOCK open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.
	DR_SILCON_UNLOCK shorted to ground inspection	OFF			There is more than 1 MOhm

Results 

• If abnormal, there is a problem in the circuit.

DR_KEY_CYL_LOCK, GND Circuit Inspection 

Test Procedure 

• Preparation
  1. -

     Driver's door latch connector (10P): disconnected

  2. -

     Power window master switch 37P connector: disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Driver's door latch connector (10P) female terminals	(Disconnected) Power window master switch 37P connector female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	DR_KEY_CYL_LOCK open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.
	DR_KEY_CYL_LOCK shorted to ground inspection	OFF			There is more than 1 MOhm

Results 

• If abnormal, there is a problem in the circuit.

FR_DOOR_SW, GND Open Wire Inspection 

Test Procedure 

• Preparation
  1. -

     Front passenger's door latch connector (10P): disconnected

  2. -

     Body control module connector B (66P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Front passenger's door latch connector (10P) female terminals	(Disconnected) Body control module connector B (66P) female terminals

		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	FR_DOOR_SW open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm

Results 

• If abnormal, there is a problem in the circuit.

AS_SILCON_UNLOCK, GND Circuit Inspection 

Test Procedure 

• Preparation
  1. -

     Front passenger's door latch connector (10P): disconnected

  2. -

     Front passenger's power window switch 37P connector: disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Front passenger's door latch connector (10P) female terminals	(Disconnected) Front passenger's power window switch 37P connector female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	AS_SILCON_UNLOCK open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.

AS_SILCON_UNLOCK shorted to ground inspection

OFF

There is more than 1 MOhm

Results 

• If abnormal, there is a problem in the circuit.

RL_DOOR_SW, GND Open Wire Inspection 

Test Procedure 

• Preparation
  1. -

     Left rear door latch connector (10P): disconnected

  2. -

     Body control module connector B (66P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Left rear door latch connector (10P) female terminals	(Disconnected) Body control module connector B (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	RL_DOOR_SW open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm

Results 

• If abnormal, there is a problem in the circuit.

RR_L_SILCON_UNLOCK, GND Circuit Inspection 

Test Procedure 

• Preparation
  1. -

     Left rear door latch connector (10P): disconnected

  2. -

     Body control module connector B (66P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Left rear door latch connector (10P) female terminals	(Disconnected) Body control module connector B (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	RR_L_SILCON_UNLOCK open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.
	RR_L_SILCON_UNLOCK shorted to ground inspection	OFF			There is more than 1 MOhm

Results 

• If abnormal, there is a problem in the circuit.

RR_DOOR_SW, GND Open Wire Inspection 

Test Procedure 

• Preparation
  1. -

     Right rear door latch connector (10P): disconnected

  2. -

     Body control module connector B (66P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected)Right rear door latch connector (10P) female terminals	(Disconnected)Body control module connector B (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	RR_DOOR_SW open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm

Results 

• If abnormal, there is a problem in the circuit.

RR_R_SILCON_UNLOCK, GND Circuit Inspection 

Test Procedure 

• Preparation
  1. -

     Right rear door latch connector (10P): disconnected

  2. -

     Body control module connector B (66P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Right rear door latch connector (10P) female terminals	(Disconnected) Body control module connector B (66P) female terminals

		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	RR_R_SILCON_UNLOCK open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.
	RR_R_SILCON_UNLOCK shorted to ground inspection	OFF			There is more than 1 MOhm

Results 

• If abnormal, there is a problem in the circuit.

TAIL_GATE_SW, GND Circuit Inspection 

Test Procedure 

• Preparation
  1. -

     Tailgate latch connector (4P): disconnected

  2. -

     Body control module connector B (66P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Tailgate latch connector (4P) female terminals	(Disconnected) Body control module connector B (66P) female terminals

		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	TAIL_GATE_SW open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.
	TAIL_GATE_SW shorted to ground inspection	OFF			There is more than 1 MOhm

Results 

• If abnormal, there is a problem in the circuit.

Body Control Module Inspection 

Test Procedure 

• If the other inspection item(s) indicated a normal condition, then it is determined that the remaining body control module is the cause.

Results 

• There is a problem with the body control module.