Values On The Diagnosis Tool
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short-circuited.
MONITOR ITEM CHART
| Monitor item | Display content | Data monitor | |
|---|---|---|---|
| Condition | Reference value in normal operation | ||
| FR LH SENSOR | Wheel speed | 0 [km/h (MPH)] | Vehicle stopped |
| Nearly matches the speed meter display (± 10 % or less) | Vehicle running (Note 1) | ||
| FR RH SENSOR | Wheel speed | 0 [km/h (MPH)] | Vehicle stopped |
| Nearly matches the speed meter display (± 10 % or less) | Vehicle running (Note 1) | ||
| RR LH SENSOR | Wheel speed | 0 [km/h (MPH)] | Vehicle stopped |
| Nearly matches the speed meter display (± 10 % or less) | Vehicle running (Note 1) | ||
| RR RH SENSOR | Wheel speed | 0 [km/h (MPH)] | Vehicle stopped |
| Nearly matches the speed meter display (± 10 % or less) | Vehicle running (Note 1) | ||
| STOP LAMP SW | Stop lamp switch signal status | When brake pedal is depressed | ON |
| When brake pedal is not depressed | OFF | ||
| BATTERY VOLT | Battery voltage supplied to the ABS actuator and electric unit (control unit) | Ignition switch ON | 10 - 16 V |
| GEAR | Gear position determined by TCM | 1st gear | 1 |
| 2nd gear | 2 | ||
| 3rd gear | 3 | ||
| 4th gear | 4 | ||
| 5th gear | 5 | ||
| SLCT LVR POSI | A/T selector lever position | P position | P |
| R position | R | ||
| N position | N | ||
| D position | D | ||
| OFF SW | VDC OFF switch ON/OFF | VDC OFF switch ON (When VDC OFF indicator lamp is ON) | ON |
| VDC OFF switch OFF (When VDC OFF indicator lamp is OFF) | OFF | ||
| YAW RATE SEN | Yaw rate detected by yaw rate/side G sensor | When vehicle stop | Approx. 0 d/s |
| When vehicle turning | -75 to 75 d/s | ||
| ACCEL POS SIG | Throttle actuator opening/closing is displayed (linked with accelerator pedal) | Accelerator pedal not depressed (ignition switch is ON) | 0 % |
| Depress accelerator pedal (ignition switch is ON) | 0 - 100 % | ||
| SIDE G-SENSOR | Transverse G detected by side G sensor | Vehicle stopped | Approx. 0 m/s2 |
| Vehicle turning right | Negative value (m/s2 ) | ||
| Vehicle turning left | Positive value (m/s2 ) | ||
| STR ANGLE SIG | Steering angle detected by steering angle sensor | Straight-ahead | Approx. 0° |
| Steering wheel turned | -720 to 720° | ||
| 4WD MODE MON (Note 2) | AWD activated | Engine running | AUTO |
| PRESS SENSOR | Brake fluid pressure detected by pressure sensor | With ignition switch turned ON and brake pedal released | Approx. 0 bar |
| With ignition switch turned ON and brake pedal depressed | -40 to 300 bar | ||
| ENGINE RPM | With engine running | With engine stopped | 0 rpm |
| Engine running | Almost in accordance with tachometer display | ||
| FLUID LEV SW | Brake fluid level switch signal status | When brake fluid level switch ON | ON |
| When brake fluid level switch OFF | OFF | ||
| PARK BRAKE SW | Parking brake switch signal status | Parking brake switch is active | ON |
| Parking brake switch is inactive | OFF | ||
| FR RH IN SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| FR RH OUT SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| FR LH IN SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| FR LH OUT SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| RR RH IN SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| RR RH OUT SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| RR LH IN SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| RR LH OUT SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| MOTOR RELAY | Motor and motor relay operation | When the motor relay and motor are operating | ON |
| When the motor relay and motor are not operating | OFF | ||
| ACTUATOR RLY (Note 3) | Actuator relay operation | When the actuator relay is operating | ON |
| When the actuator relay is not operating | OFF | ||
| ABS WARN LAMP | ABS warning lamp (Note 4) | When ABS warning lamp is ON | ON |
| When ABS warning lamp is OFF | OFF | ||
| OFF LAMP | VDC OFF indicator lamp (Note 4) | When VDC OFF indicator lamp is ON | ON |
| When VDC OFF indicator lamp is OFF | OFF | ||
| SLIP LAMP | SLIP indicator lamp (Note 4) | When SLIP indicator lamp is ON | ON |
| When SLIP indicator lamp is OFF | OFF | ||
| SNOW MODE SW | SNOW mode switch | When snow mode switch is ON | ON |
| When snow mode switch is OFF | OFF | ||
| 4WD FAIL REQ (Note 2) | AWD control unit fail-safe signal | When AWD control unit is fail-safe mode | ON |
| When AWD control unit is normal | OFF | ||
| BST OPER SIG | Not applied but displayed | - | OFF |
| M-MODE SIG | Manual mode activated | When the manual mode is active | ON |
| When the manual mode is inactive | OFF | ||
| EBD SIGNAL | EBD operation | EBD is active | ON |
| EBD is inactive | OFF | ||
| ABS SIGNAL | ABS operation | ABS is active | ON |
| ABS is inactive | OFF | ||
| TCS SIGNAL | TCS operation | TCS is active | ON |
| TCS is inactive | OFF | ||
| VDC SIGNAL | VDC operation | VDC is active | ON |
| VDC is inactive | OFF | ||
| EBD FAIL SIG | EBD fail-safe signal | In EBD fail-safe | ON |
| EBD is normal | OFF | ||
| ABS FAIL SIG | ABS fail-safe signal | In ABS fail-safe | ON |
| ABS is normal | OFF | ||
| TCS FAIL SIG | TCS fail-safe signal | In TCS fail-safe | ON |
| TCS is normal | OFF | ||
| VDC FAIL SIG | VDC fail-safe signal | In VDC fail-safe | ON |
| VDC is normal | OFF | ||
| CRANKING SIG | Crank operation | Crank is active | ON |
| Crank is inactive | OFF | ||
| USV [FL-RR] (Note 3) | VDC switch-over valve | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (when in failsafe mode) | ON |
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| USV [FR-RL] (Note 3) | VDC switch-over valve | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (when in failsafe mode) | ON |
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| HSV [FL-RR] (Note 3) | VDC switch-over valve | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (when in failsafe mode) | ON |
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| HSV [FR-RL] (Note 3) | VDC switch-over valve | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (when in failsafe mode) | ON |
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| V/R OUTPUT (Note 3) | Solenoid valve relay activated | When the solenoid valve relay is active (When ignition switch OFF) | ON |
| When the solenoid valve relay is not active (in the fail-safe mode) | OFF | ||
| M/R OUTPUT | Actuator motor and motor relay activated | When the actuator motor and motor relay are active ("ACTIVE TEST" with CONSULT-III) | ON |
| When the actuator motor and motor relay are inactive | OFF | ||
|
NOTE:
|
|||