Values On The Diagnosis Tool
WARNING: This page is about a different car, the 2008 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short-circuited.
CONSULT-III MONITOR ITEM
ECU DIAGNOSIS REFERENCE VALUE CHART
| Monitor item | Display content | Data monitor | |
|---|---|---|---|
| Condition | Reference value in normal operation | ||
| FR LH SENSOR | Wheel speed | 0 [km/h (MPH)] | Vehicle stopped |
| Nearly matches the speed meter display (± 10% or less) | Vehicle running (Note 1) | ||
| FR RH SENSOR | Wheel speed | 0 [km/h (MPH)] | Vehicle stopped |
| Nearly matches the speed meter display (± 10% or less) | Vehicle running (Note 1) | ||
| RR LH SENSOR | Wheel speed | 0 [km/h (MPH)] | Vehicle stopped |
| Nearly matches the speed meter display (± 10% or less) | Vehicle running (Note 1) | ||
| RR RH SENSOR | Wheel speed | 0 [km/h (MPH)] | Vehicle stopped |
| Nearly matches the speed meter display (± 10% or less) | Vehicle running (Note 1) | ||
| STOP LAMP SW | Stop lamp switch signal status | When brake pedal is depressed | ON |
| When brake pedal is released | OFF | ||
| BATTERY VOLT | Battery voltage supplied to the ABS actuator and electric unit (control unit) | Ignition switch ON | 10 - 16 V |
| GEAR | Gear position determined by TCM | 1st gear 2nd gear 3rd gear 4th gear 5th gear |
1 2 3 4 5 |
| SLCT LVR POSI | A/T selector lever position | P position R position N position D position |
P R N D |
| ACCEL POS SIG | Throttle actuator opening/closing is displayed (linked with accelerator pedal) | Accelerator pedal not depressed (ignition switch is ON) | 0 % |
| Accelerator pedal depressed (ignition switch is ON) | 0 - 100 % | ||
| PRESS SENSOR | Brake fluid pressure detected by front pressure sensor | With ignition switch turned ON and brake pedal released | Approx. 0 bar |
| With ignition switch turned ON and brake pedal depressed | -40 to 300 bar | ||
| ENGINE SPEED | With engine running | With engine stopped | 0 rpm |
| Engine running | Almost in accordance with tachometer display | ||
| FLUID LEV SW | Brake fluid level switch signal status | When brake fluid level switch ON | ON |
| When brake fluid level switch OFF | OFF | ||
| FR RH IN SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| FR RH OUT SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| FR LH IN SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| FR LH OUT SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| RR RH IN SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| RR RH OUT SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| RR LH IN SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| RR LH OUT SOL | Operation status of each solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| MOTOR RELAY | Motor and motor relay operation | When the motor relay and motor are operating | OFN |
| When the motor relay and motor are not operating | OFF | ||
| ACTUATOR RLY | Actuator relay operation | When the actuator relay is operating | ON |
| When the actuator relay is not operating | OFF | ||
| ABS WARN LAMP | ABS warning lamp (Note 2) | When ABS warning lamp is ON | ON |
| When ABS warning lamp is OFF | OFF | ||
| SLIP LAMP | SLIP indicator lamp (Note 2) | When SLIP indicator lamp is ON | ON |
| When SLIP indicator lamp is OFF | OFF | ||
| EBD SIGNAL | EBD operation | EBD is active | ON |
| EBD is inactive | OFF | ||
| ABS SIGNAL | ABS operation | ABS is active | ON |
| ABS is inactive | OFF | ||
| TCS SIGNAL | ABLS operation | ABLS is active | ON |
| ABLS is inactive | OFF | ||
| EBD FAIL SIG | EBD fail-safe signal | In EBD fail-safe | ON |
| EBD is normal | OFF | ||
| ABS FAIL SIG | ABS fail-safe signal | In ABS fail-safe | ON |
| ABS is normal | OFF | ||
| TCS FAIL SIG | ABLS fail-safe signal | In ABLS fail-safe | ON |
| ABLS is normal | OFF | ||
| CRANKING SIG | Crank operation | Crank is active | ON |
| Crank is inactive | OFF | ||
| CV1 | Switch-over valve | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (when in failsafe mode) | ON |
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| CV2 | Switch-over valve | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (when in failsafe mode) | ON |
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| SV1 | Switch-over valve | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (when in failsafe mode) | ON |
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| SV2 | Switch-over valve | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (when in failsafe mode) | ON |
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||
| DECEL G-SEN | Longitudinal acceleration detected by Decel G-Sensor | Vehicle stopped | Approx. 0 G |
| Vehicle running | -1.7 to 1.7 G | ||
| EBD WARN LAMP | EBD warning lamp (Note 2) | When EBD warning lamp is ON | ON |
| When EBD warning lamp is OFF | OFF | ||
| N POSI SIG | PNP switch signal ON/OFF condition | A/T shift position = N position | ON |
| A/T shift position = other than N position | OFF | ||
| P POSI SIG | PNP switch signal ON/OFF condition | A/T shift position = P position | ON |
| A/T shift position = other than P position | OFF | ||
| R POSI SIG | PNP switch signal ON/OFF condition | A/T shift position = R position | ON |
| A/T shift position = other than R position | OFF | ||
| 2WD/4WD | Drive axle | 2WD model | 2WD |
| 4WD model | 4WD | ||
| PRESS SEN2 | Brake fluid pressure detected by rear pressure sensor | With ignition switch turned ON and brake pedal released | Approx. 0 bar |
| With ignition switch turned ON and brake pedal depressed | -40 to 300 bar | ||
NOTE:
- 1: Confirm tire pressure is normal.
- 2: On and off timing for warning lamp and indicator lamp.
- ABS warning lamp: Refer to , "DESCRIPTION ".
- Brake warning lamp: Refer to , "DESCRIPTION ".
- SLIP indicator lamp: Refer to , "DESCRIPTION ".