Confirmation/Adjustment Mode

1. Start the diagnosis function and select "Confirmation/Adjustment". The confirmation/adjustment mode indicates where each item can be checked or adjusted.
2. Select each switch on the "Confirmation/Adjustment Mode" screen to display the relevant trouble diagnosis screen. Press the "BACK" switch to return to the initial Confirmation/Adjustment Mode screen.
   Fig 1: Confirmation / Adjustment - Screen Display

   Courtesy of NISSAN MOTOR CO., U.S.A.

Display Diagnosis

The tint of the color bar indication is as per the following list if RGB signal error is detected.

R (red) signal error : Light blue (Cyan) tint 

G (green) signal error : Purple (Magenta) tint 

B (blue) signal error : Yellow tint 

Vehicle Signals

A comparison check can be made of each actual vehicle signal and the signals recognized by the system.

Diagnosis item	Display	Vehicle status	Remarks
Vehicle speed	ON	Vehicle speed > 0 km/h (0 MPH)	Changes in indication may be delayed. This is normal.
	OFF	Vehicle speed = 0 km/h (0 MPH)
Parking brake	ON	Parking brake is applied.
	OFF	Parking brake is released.
Lights	ON	Light switch ON	-
	OFF	Light switch OFF
Ignition	ON	Ignition switch ON	-
	OFF	Ignition switch in ACC position
Reverse	ON	Shift the selector lever to "R" position	Changes in indication may be delayed. This is normal.
	OFF	Shift the selector lever other than "R" position

Speaker Test

Select "Speaker Test" to display the speaker test screen. Press "Start" to generate a test tone in a speaker. Press "Start" again to generate a test tone in the next speaker. Press "End" to stop the test tones.

Tweeter : 3 kHz 

Front speaker : 300 Hz 

Rear speaker : 1 kHz 

Climate Control

Refer to "HEATER & AIR CONDITIONING CONTROL SYSTEM " for details.

Error History

The self-diagnosis results are judged depending on whether any error occurs from when "Self-diagnosis" is selected until the self-diagnosis results are displayed.

However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned ON and then no error has occurred until the self-diagnosis start. Check the "Error Record" to detect any error that may have occurred before the self-diagnosis start because of this situation.

Count up method A

• The counter resets to 0 if an error occurs when ignition switch is turned ON. The counter increases by 1 if the condition is normal at a next ignition ON cycle.
• The counter upper limit is 39. Any counts exceeding 39 are ignored. The counter can be reset (no error record display) with the "Delete log" switch or CONSULT-III.

Count up method B

• The counter increases by 1 if an error occurs when ignition switch is ON. The counter will not decrease even if the condition is normal at the next ignition ON cycle.
• The counter upper limit is 50. Any counts exceeding 50 are ignored. The counter can be reset (no error record display) with the "Delete log" switch or CONSULT-III.
  OCCURRENCE FREQUENCY REFERENCE
  
  

  Display type of occurrence frequency	Error history display item
  Count up method A	CAN communication line, control unit (CAN), AV communication line, control unit (AV)
  Count up method B	Other than the above

  Fig 5: Error History - Screen Display

  Courtesy of NISSAN MOTOR CO., U.S.A.

Error item

Some error items may be displayed simultaneously according to the cause. If some error items are displayed simultaneously, the detection of the cause can be performed by the combination of display items

Error item	Description	Possible malfunction factor/Action to take
CAN COMM CIRCUIT	CAN communication malfunction is detected.	Perform diagnosis with CONSULT-III, and then repair the malfunctioning parts according to the diagnosis results. Refer to "CONSULT - III FUNCTION (MULTI AV) ".
CONTROL UNIT (CAN)	CAN initial diagnosis malfunction is detected.	Replace the AV control unit.
CONTROL UNIT (AV)	AV communication circuit initial diagnosis malfunction is detected.
FLASH-ROM Error Of Control Unit	AV control unit malfunction is detected.
CAN Controller Memory Error
Amplifier Temperature Error	BOSE amp. malfunction is detected.	Replace the BOSE amp.
Front Display Connection Error	Display unit power supply and ground circuit malfunction is detected. Malfunction is detected in communication circuit between AV control unit and display unit. Malfunction is detected in communication signal between AV control unit and display unit.	Display unit power supply and ground circuit. Communication circuit between AV control unit and display unit.
Camera Control Unit Connection Error	Malfunction is detected in camera connection recognition circuit between AV control unit and camera control unit.	Camera connection recognition circuit between AV control unit and camera control unit.
SAT Connection Error	Satellite radio tuner power supply and ground circuit malfunction is detected. Malfunction is detected in communication circuit between AV control unit and satellite radio tuner. Malfunction is detected in communication signal between AV control unit and satellite radio tuner. Malfunction is detected in request signal circuit between AV control unit and satellite radio tuner.	Satellite radio tuner power supply and ground circuit. Communication circuit between AV control unit and satellite radio tuner. Request signal circuit between AV control unit and satellite radio tuner.
Center speaker OUT: open	Sound signal center speaker circuit is open.	Check sound signal center speaker circuit.
Center speaker OUT: short	Sound signal center speaker circuit is shorted between center speaker signal (+) and center speaker signal (-).	Check sound signal center speaker circuit.
Center speaker OUT: short to ground	Sound signal center speaker circuit to ground is shorted.	Check sound signal center speaker circuit.
Center speaker OUT: short to battery	Sound signal center speaker circuit to battery is shorted.	Check sound signal center speaker circuit.
FR speaker OUT: open	Sound signal front speaker RH circuit is open.	Check sound signal front speaker RH circuit.
FR speaker OUT: short	Sound signal front speaker RH circuit is shorted between front speaker RH signal (+) and front speaker RH signal (-).	Check sound signal front speaker RH circuit.
FR speaker OUT: short to ground	Sound signal front speaker RH circuit to ground is shorted.	Check sound signal front speaker RH circuit.
FR speaker OUT: short to battery	Sound signal front speaker RH circuit to battery is shorted.	Check sound signal front speaker RH circuit.
RR speaker OUT: open	Sound signal door woofer RH circuit is open.	Check sound signal door woofer RH circuit.
RR speaker OUT: short	Sound signal door woofer RH circuit is shorted between rear door woofer RH signal (+) and door woofer RH signal (-).	Check sound signal door woofer RH circuit.
RR speaker OUT: short to ground	Sound signal door woofer RH circuit to ground is shorted.	Check sound signal door woofer RH circuit.
RR speaker OUT: short to battery	Sound signal door woofer RH circuit to battery is shorted.	Check sound signal door woofer RH circuit.
RR SR-speaker OUT: open	Sound signal rear woofer RH circuit is open.	Check sound signal rear woofer RH circuit.
RR SR-speaker OUT: short	Sound signal rear woofer RH circuit is shorted between rear woofer RH signal (+) and rear woofer RH signal (-).	Check sound signal rear woofer RH circuit.
RR SR-speaker OUT: short to ground	Sound signal rear woofer RH circuit to ground is shorted.	Check sound signal rear woofer RH circuit.
RR SR-speaker OUT: short to battery	Sound signal rear woofer RH circuit to battery is shorted.	Check sound signal rear woofer RH circuit.
RL SR-speaker OUT: open	Sound signal rear woofer LH circuit is open.	Check sound signal rear woofer LH circuit.
RL SR-speaker OUT: short	Sound signal rear woofer LH circuit is shorted between rear woofer LH signal (+) and rear woofer LH signal (-).	Check sound signal rear woofer LH circuit.
RL SR-speaker OUT: short to ground	Sound signal rear woofer LH circuit to ground is shorted.	Check sound signal rear woofer LH circuit.
RL SR-speaker OUT: short to battery	Sound signal rear woofer LH circuit to battery is shorted.	Check sound signal rear woofer LH circuit.
RL speaker OUT: open	Sound signal door woofer LH circuit is open.	Check sound signal door woofer LH circuit.
RL speaker OUT: short	Sound signal door woofer LH circuit is shorted between door woofer LH signal (+) and door woofer LH signal (-).	Check sound signal door woofer LH circuit.
RL speaker OUT: short to ground	Sound signal door woofer LH circuit to ground is shorted.	Check sound signal door woofer LH circuit.
RL speaker OUT: short to battery	Sound signal door woofer LH circuit to battery is shorted.	Check sound signal door woofer LH circuit.
FL speaker OUT: open	Sound signal front speaker LH circuit is open.	Check sound signal front speaker LH circuit.
FL speaker OUT: short	Sound signal front speaker LH circuit is shorted between front speaker LH signal (+) and front speaker LH signal (-).	Check sound signal front speaker LH circuit.
FL speaker OUT: short to ground	Sound signal front speaker LH circuit to ground is shorted.	Check sound signal front speaker LH circuit.
FL speaker OUT: short to battery	Sound signal front speaker LH circuit to battery is shorted.	Check sound signal front speaker LH circuit.
FL seat SP(L) OUT: open	Sound signal driver headrest speaker LH circuit is open.	Check sound signal driver headrest speaker LH circuit.
FL seat SP(L) OUT: short	Sound signal driver headrest speaker LH circuit is shorted between driver headrest speaker LH signal (+) and driver headrest speaker LH signal (-).	Check sound signal driver headrest speaker LH circuit.
FL seat SP(L) OUT: short to ground	Sound signal driver headrest speaker LH circuit to ground is shorted.	Check sound signal driver headrest speaker LH circuit.
FL seat SP(L) OUT: short to battery	Sound signal driver headrest speaker LH circuit to battery is shorted.	Check sound signal driver headrest speaker LH circuit.
FL seat SP(R) OUT: open	Sound signal driver headrest speaker RH circuit is open.	Check sound signal driver headrest speaker RH circuit.
FL seat SP(R) OUT: short	Sound signal driver headrest speaker RH circuit is shorted between driver headrest speaker RH signal (+) and driver headrest speaker RH signal (-).	Check sound signal driver headrest speaker RH circuit.
FL seat SP(R) OUT: short to ground	Sound signal driver headrest speaker RH circuit to ground is shorted.	Check sound signal driver headrest speaker RH circuit.
FL seat SP(R) OUT: short to battery	Sound signal driver headrest speaker RH circuit to battery is shorted.	Check sound signal driver headrest speaker RH circuit.
FR seat SP(L) OUT: open	Sound signal passenger headrest speaker LH circuit is open.	Check sound signal passenger headrest speaker LH circuit.
FR seat SP(L) OUT: short	Sound signal passenger headrest speaker LH circuit is shorted between passenger headrest speaker LH signal (+) and passenger headrest speaker LH signal (-).	Check sound signal passenger headrest speaker LH circuit.
FR seat SP(L) OUT: short to ground	Sound signal passenger headrest speaker LH circuit to ground is shorted.	Check sound signal passenger headrest speaker LH circuit.
FR seat SP(L) OUT: short to battery	Sound signal passenger headrest speaker LH circuit to battery is shorted.	Check sound signal passenger headrest speaker LH circuit.
FR seat SP(R) OUT: open	Sound signal passenger headrest speaker RH circuit is open.	Check sound signal passenger headrest speaker RH circuit.
FR seat SP(R) OUT: short	Sound signal passenger headrest speaker RH circuit is shorted between passenger headrest speaker RH signal (+) and passenger headrest speaker RH signal (-).	Check sound signal passenger headrest speaker RH circuit.
FR seat SP(R) OUT: short to ground	Sound signal passenger headrest speaker RH circuit to ground is shorted.	Check sound signal passenger headrest speaker RH circuit.
FR seat SP(R) OUT: short to battery	Sound signal passenger headrest speaker RH circuit to battery is shorted.	Check sound signal passenger headrest speaker RH circuit.
Compensat. mic IN: open	Mic. signal (for AudioPilot®) circuit is open.	Check Mic. signal (for AudioPilot®) circuit.
Compensat. mic IN: short	Mic. signal (for AudioPilot®) circuit is shorted between MIC. signal (for AudioPilot®) (+) and MIC. signal (for AudioPilot®) (-).	Check Mic. signal (for AudioPilot®) circuit.
Compensat. mic IN: short to ground	Mic. signal (for AudioPilot®) circuit to ground is shorted.	Check Mic. signal (for AudioPilot®) circuit.
Compensat. mic IN: short to battery	Mic. signal (for Audiopilot®) circuit to battery is shorted.	Check Mic. signal (for AudioPilot®) circuit.
AV COMM CIRCUIT Switches Connection Error	Multifunction switch power supply and ground circuit malfunction is detected. Malfunction is detected in AV communication circuit between AV control unit and multifunction switch. Malfunction is detected in AV communication signal between AV control unit and multifunction switch.	Multifunction switch power supply and ground circuit. AV communication circuit between AV control unit and multifunction switch.
AV COMM CIRCUIT Amplifier Connection Error	BOSE amp. power supply and ground circuits are malfunctioning.	BOSE amp. power supply and ground circuits.
AV COMM CIRCUIT Rearview Camera Connection Error	Camera control unit power supply and ground circuits malfunction is detected.	Camera control unit power supply and ground circuits.
AV COMM CIRCUIT iPod Connection Error	iPod adapter power supply and ground circuit malfunction is detected. Malfunction is detected in AV communication circuit between multifunction switch and iPod adapter. Malfunction is detected in AV communication signal between AV control unit and iPod adapter.	iPod adapter power supply and ground circuit. AV communication circuit between multifunction switch and iPod adapter.
AV COMM CIRCUIT H/F Unit Connection Error	TEL adapter unit power supply and ground circuit malfunction is detected. Malfunction is detected in AV communication circuit between BOSE amp. and camera control unit. Malfunction is detected in AV communication circuit between camera control unit and TEL adapter unit. Malfunction is detected in AV communication signal between AV control unit and TEL adapter unit.	TEL adapter unit power supply and ground circuit. AV communication circuit between BOSE amp. and camera control unit. AV communication circuit between camera control unit and TEL adapter unit.
AV COMM CIRCUIT Rearview Camera Connection Error H/F Unit Connection Error	Malfunction is detected in AV communication circuit between BOSE amp. and camera control unit.	AV communication circuit between BOSE amp. and camera control unit.
AV COMM CIRCUIT Rearview Camera Connection Error H/F Unit Connection Error Amplifier Connection Error	Malfunction is detected in AV communication circuit between iPod adapter and BOSE amp.	AV communication circuit between iPod adapter and BOSE amp.
AV COMM CIRCUIT Rearview Camera Connection Error iPod Unit Connection Error H/F Unit Connection Error Amplifier Connection Error	Malfunction is detected in AV communication circuit between AV control unit and iPod adapter.	AV communication circuit between AV control unit and iPod adapter.
AV COMM CIRCUIT Switches Connection Error Rearview Camera Connection Error iPod Unit Connection Error H/F Unit Connection Error Amplifier Connection Error	Malfunction is detected in AV communication circuit between AV control unit and multifunction switch.	AV communication circuit between AV control unit and multifunction switch.

Camera Cont.

The two functions of "Connection Confirmation" and "Adjust Offset of Rear View Camera" are available.

CONNECTION CONFIRMATION

The steering angle sensor, reverse signal and vehicle speed sensor can be inspected.

Diagnosis item	Display	Vehicle status
Steer. Angle Sensor	ON	When steering the vehicle with ignition switch ON (remains ON until connection mode is stopped when it is turned ON)
	OFF	Ignition switch at ACC No steering with ignition switch ON
	-	Malfunction detected in camera connection recognition signal
Reverse Sensor	ON	Selector lever is in "R" with ignition switch ON.
	OFF	Ignition switch at ACC Selector lever is in position other than "R" with ignition switch ON.
	-	Malfunction detected in camera-connection recognition signal
Vehicle Speed Sensor	ON	Vehicle speed is more than 0 km/h (0 MPH) with ignition switch ON
	OFF	Ignition switch at ACC Vehicle speed is 0 km/h (0 MPH) with ignition switch ON
	-	Malfunction detected in camera connection recognition signal
Side view Switch	-	Not used