XM Sat Subscription Status

The XM NavTraffic subscription status can be checked.

Error History

The self-diagnosis results are judged depending on whether any error occurs from when "Self-diagnosis" is selected until the self-diagnosis results are displayed.

However, the diagnosis results are judged normal if an error has occurred before the ignition SW is turned ON and then no error has occurred until the self-diagnosis start. Check the "Error Record" to detect any error that may have occurred before the self-diagnosis start because of this condition.

The error record displays the time and place of the most recent occurrence of that error. However, take note of the following points.

• If there is a malfunction with the GPS antenna circuit board in AV control unit, the correct date and time of occurrence may not be displayed.
• Place of the error occurrence is represented by the position of the current location mark at the time an error occurred. If current location mark has deviated from the correct position, then the place of the error occurrence cannot be located correctly.
• The frequency of occurrence is displayed in a count up manner. The actual count up method differs depending on the error item.

Count up method A

• The counter resets to 0 if an error occurs when IGN switch is turned ON. The counter increases by 1 if the condition is normal at a next IGN ON cycle.
• The counter upper limit is 39. Any counts exceeding 39 are ignored. The counter can be reset (no error record display) with the "Delete log" switch or CONSULT-III.

Count up method B

• The counter increases by 1 if an error occurs when IGN switch is ON. The counter will not decrease even if the condition is normal at the next IGN ON cycle.
• The counter upper limit is 50. Any counts exceeding 50 are ignored. The counter can be reset (no error record display) with the "Delete log" switch or CONSULT-III.

Display type of occurrence frequency	Error history display item
Count up method A	CAN communication line, control unit (CAN), AV communication line, control unit (AV communication)
Count up method B	Other than the above

Error item

Some error items may be displayed simultaneously according to the cause. If some error items are displayed simultaneously, the detection of the cause can be performed by the combination of display items.

Error item	Detection logic	Possible malfunction factor/Action to take
CAN COMM CIRCUIT	CAN communication malfunction is detected.	Perform diagnosis with CONSULT-III, and then repair the malfunctioning parts according to the diagnosis results. Refer to CONSULT-III FUNCTION (MULTI AV) .
CONTROL UNIT (CAN)	CAN initial diagnosis malfunction is detected.	Replace AV control unit.
CONTROL UNIT (AV)	AV communication circuit initial diagnosis malfunction is detected.
FLASH-ROM Error Of Control Unit	AV control unit malfunction is detected.
Connection Of Gyro
XM SERIAL COMM Error
CAN Controller Memory Error
Bluetooth Module Connection Error
HDD CONN Error
HDD READ Error
HDD WRITE Error
HDD COMM Error
HDD ACCESS Error
DSP CONN Error
DSP COMM Error
Internal Communication Error	When either one of the following items are detected: malfunction is detected in AV control unit power supply and ground circuits. AV control unit malfunction is detected.	AV control unit power supply and ground circuits. When there is no malfunction, AV control unit is malfunctioning.
GPS Communication Error	GPS malfunction is detected.	An intermittent error caused by strong radio interference may be detected unless any symptom (GPS reception error, etc. occurs. Replace AV control unit if the malfunction occurs constantly.
GPS ROM Error
GPS RAM Error
GPS RTC Error
Front Display Connection Error	When either one of the following items are detected: front display unit power supply and ground circuits malfunction are detected. malfunction is detected in the communication circuits between AV control unit and front display unit. malfunction is detected in the communication signal between AV control unit and front display unit.	Front display unit power supply and ground circuits. Communication circuits between AV control unit and front display unit.
GPS Antenna Error	GPS antenna connection malfunction is detected.	GPS antenna.
XM Antenna Connection Error	Poor connection is detected in satellite radio antenna.	Satellite radio antenna feeder. Satellite radio antenna.
AV COMM CIRCUIT Internal Communication Error	When either one of the following items are detected: AV control unit power supply and ground circuits malfunction are detected. AV control unit malfunction is detected.	AV control unit power supply and ground circuits. When there is no malfunction, AV control unit is malfunctioning.
AV COMM CIRCUIT Switches Connection Error	When either one of the following items are detected: multifunction switch power supply and ground circuits malfunction are detected. malfunction is detected in the AV communication circuits between AV control unit and multifunction switch. malfunction is detected in the AV communication signal between AV control unit and multifunction switch.	Multifunction switch power supply and ground circuits. AV communication circuits between AV control unit and multifunction switch.
AV COMM CIRCUIT iPod Connection Error	When either one of the following items are detected: iPod adapter power supply and ground circuits malfunction are detected. malfunction is detected in the AV communication circuits between AV control unit and iPod adapter. malfunction is detected in the AV communication signal between AV control unit and iPod adapter.	iPod adapter power supply and ground circuits. AV communication circuits between AV control unit and iPod adapter.
AV COMM CIRCUIT AVM Connection Error	When either one of the following items are detected: around view monitor control unit power supply and ground circuits malfunction are detected. malfunction is detected in the AV communication circuits between AV control unit and around view monitor control unit. malfunction is detected in the AV communication signal between AV control unit and around view monitor control unit.	Around view monitor control unit power supply and ground circuits. AV communication circuits between AV control unit and around view monitor control unit.
AV COMM CIRCUIT AVM Sonar Connection Error	When either one of the following items are detected: sonar control unit power supply or ground circuits malfunction are detected. malfunction is detected in the AV communication circuits between around view monitor control unit and sonar control unit. malfunction is detected in the AV communication signal between around view monitor control unit and sonar control unit.	Sonar control unit power supply and ground circuits. AV communication circuits between around view monitor control unit and sonar control unit.
AV COMM CIRCUIT Switches Connection Error iPod Connection Error AVM Connection Error	Malfunction is detected in the AV communication circuits between AV control unit and around view monitor control unit.	AV communication circuits between AV control unit and around view monitor control unit.

Vehicle CAN Diagnosis

• CAN communication status and error counter is displayed.
• The error counter displays "OK" if any malfunction was not detected in the past and displays "0" if a malfunction is detected. It increases by 1 if the condition is normal at the next ignition switch ON cycle. The upper limit of the counter is 39.
• The error counter is erased if "Reset" is pressed.
  VEHICLE CAN DIAGNOSIS REFERENCE TABLE
  
  

  Items	Display (Current)	Malfunction counter (Past)
  Tx (HVAC)	OK / UNKWN	OK / 0 - 39
  Rx (ECM)	OK / UNKWN	OK / 0 - 39
  Rx (Cluster)	OK / UNKWN	OK / 0 - 39
  Rx (BCM)	OK / UNKWN	OK / 0 - 39
  Rx (HVAC)	OK / UNKWN	OK / 0 - 39
  Rx (USM)	OK / UNKWN	OK / 0 - 39
  Rx (TPMS)	OK / UNKWN	OK / 0 - 39

  Fig 3: Screen Display - Vehicle CAN Diagnosis

  Courtesy of NISSAN MOTOR CO., U.S.A.

AV COMM Diagnosis

• Displays the communication status between AV control unit (master unit) and each unit.
• The error counter displays "OK" if any malfunction was not detected in the past and displays "0" if a malfunction is detected. It increases by 1 if the condition is normal at the next ignition switch ON cycle. The upper limit of the counter is 39.
• The error counter is erased if reset.
  Fig 4: Screen Display - AV COMM Diagnosis

  Courtesy of NISSAN MOTOR CO., U.S.A.
  AV COMM DIAGNOSIS REFERENCE TABLE
  
  

  Items	Status (Current)	Counter (Past)
  C Tx (ITM-PrimarySW)	OK / UNKWN	OK / 0 - 39
  C Rx (PrimarySW-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx (STRG SW-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx (Audio-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx (Amp-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx (XM-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx (iPod-ITM)	OK / UNKWN	OK / 0 - 39
  C RX (AVM-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx (Amp-Audio)	-	-
  C Rx (iPod-Audio)	OK / UNKWN	OK / 0 - 39
  C Rx (Sonar-AVM)	OK / UNKWN	OK / 0 - 39
  C Tx (Audio-ITM)	OK / UNKWN	OK / 0 - 39
  NOTE: "Audio" and "Amp" indicate the same status because "Amp" indicates the status of the amplifier integrated in AV control unit. "STRG SW", "Amp" and "XM" indicate the same status as "Audio".

Hands-Free Phone

The hands-free phone reception volume adjustment, microphone and speaker test, and memory erase functions are also available.

Camera Cont.

Refer to DIAGNOSIS DESCRIPTION .

Bluetooth

Confirm/Change Passkey

• The passkey of Bluetooth can be confirmed and changed.
• The passkey can be changed by four digits within 0 to 9.
  Fig 6: Screen Display - Confirm/Change Passkey

  Courtesy of NISSAN MOTOR CO., U.S.A.

Confirm/Change Device Name

• The device name of Bluetooth can be confirmed and changed.
• The device name can be changed by sixteen digits within A to Z (small character can be used) and - (hyphen).
  Fig 7: Screen Display - Confirm/Change Device Name

  Courtesy of NISSAN MOTOR CO., U.S.A.

SAT

• Change Channel
  • Any necessary channels required to receive traffic information from the satellite radio system can be set.
    Fig 8: Screen Display - Change Channel

    Courtesy of NISSAN MOTOR CO., U.S.A.
• Change Application ID
  • Any application IDs required to receive traffic information from the satellite radio system can be set.
    Fig 9: Screen Display - Change Application ID

    Courtesy of NISSAN MOTOR CO., U.S.A.

Delete Unit Connection Log

Deletes any unit connection records and error records from AV control unit memory. Clear the records of the unit that has been removed.

Initialize Settings

Deletes data stored in HDD.