LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2011 >> FX35 AWD >> Repair and Diagnosis (Single Page) >> External Pages >> Different car >> Section 134 (Engine Control System - Introduction) >> System Description >> Diagnosis System (ECM) >> Diagnosis Description >> CONSULT-III Function >> Active Test Mode
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Active Test Mode

WARNING: This page is about a different car, the 2011 Infiniti EX35. However, it is still accessible from the selected car via links, so may be relevant.

Test Item

TEST ITEM CONDITION

TEST ITEM CONDITION JUDGEMENT CHECK ITEM (REMEDY)
VENT CONTROL/V
  • Ignition switch: ON (Engine stopped)
  • Turn solenoid valve ON and OFF with the CONSULT-III and listen to operating sound.
 Solenoid valve makes an operating sound.
  • Harness and connectors
  • Solenoid valve
ENG COOLANT TEMP
  • Engine: Return to the original trouble condition
  • Change the engine coolant temperature using CONSULT-III.
 If trouble symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Engine coolant temperature sensor
  • Fuel injector
FUEL INJECTION
  • Engine: Return to the original trouble condition Change the amount of fuel injection using CONSULT-III.
 If trouble symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Fuel injector
  • Air fuel ratio (A/F) sensor 1
FUEL/T TEMP SEN
  • Change the fuel tank temperature using CONSULT-III.
PURG VOL CONT/V
  • Engine: After warming up, run engine at 1, 500 RPM.
  • Change the EVAP canister purge volume control solenoid valve opening percent using CONSULT-III.
 Engine speed changes according to the opening percent.
  • Harness and connectors
  • Solenoid valve
FUEL PUMP RELAY
  • Ignition switch: ON (Engine stopped)
  • Turn the fuel pump relay ON and OFF using CONSULT-III and listen to operating sound.
 Fuel pump relay makes the operating sound.
  • Harness and connectors
  • Fuel pump relay
IGNITION TIMING
  • Engine: Return to the original trouble condition
  • Timing light: Set
  • Retard the ignition timing using CONSULT-III.
 If trouble symptom disappears, see CHECK ITEM.
  • Perform Idle Air Volume Learning.
FAN DUTY CONTROL(1)
  • Ignition switch: ON
  • Change duty ratio using CONSULT-III.
 Cooling fan speed changes.
  • Harness and connectors
  • Cooling fan motor
  • Cooling fan relay
  • Cooling fan control module
  • IPDM E/R
ALTERNATOR DUTY
  • Engine: Idle
  • Change duty ratio using CONSULT-III.
 Battery voltage changes.
  • Harness and connectors
  • IPDM E/R
  • Alternator
POWER BALANCE
  • Engine: After warming up, idle the engine.
  • A/C switch OFF
  • Selector lever: P or N (A/T), Neutral (M/T)
  • Cut off each injector signal one at a time using CONSULT-III.
 Engine runs rough or dies.
  • Harness and connectors
  • Compression
  • Fuel injector
  • Power transistor
  • Spark plug
  • Ignition coil
INT V/T ASSIGN ANGLE
  • Engine: Return to the original non-standard condition
  • Change intake valve timing using CONSULT-III.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Intake valve timing control solenoid valve
EXH V/T ASSIGN ANGLE
  • Engine: Return to the original non-standard condition
  • Change exhaust valve timing using CONSULT-III.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Exhaust valve timing control magnet retarder
(1) Leaving cooling fan OFF with CONSULT-III while engine is running may cause the engine to overheat.
scientia non olet · About LEMON Manuals