Confirmation/Adjustment Mode

1. Start the diagnosis function and select "Confirmation/Adjustment". The confirmation/adjustment mode indicates where each item can be checked or adjusted.
2. Select each switch on the "Confirmation/Adjustment Mode" screen to display the relevant trouble diagnosis screen. Press the "Back" switch to return to the initial Confirmation/Adjustment Mode screen.
   Fig 1: Screen Display - Confirmation/Adjustment Mode

   Courtesy of NISSAN MOTOR CO., U.S.A.

Display Diagnosis

Fig 2: Screen - Display Diagnosis

Courtesy of NISSAN MOTOR CO., U.S.A.

Vehicle Signals

A comparison check can be made of each actual vehicle signal and the signals recognized by the system.

Fig 3: Screen Display - Vehicle Signal

Courtesy of NISSAN MOTOR CO., U.S.A.

Speaker Test

Select "SPEAKER DIAGNOSIS" to display the Speaker Diagnosis screen. Press "Start" to generate a test tone in a speaker. Press "Start" to generate a test tone in the next speaker. Press "Stop" to stop the test tones.

Fig 4: Screen Display - System Diagnosis Menu

Courtesy of NISSAN MOTOR CO., U.S.A.

Navigation

STEERING ANGLE ADJUSTMENT

The steering angle output value detected with the gyroscope is adjusted.

Fig 5: Screen Display - Steering Angle Adjustment

Courtesy of NISSAN MOTOR CO., U.S.A.

SPEED CALIBRATION

During normal driving, distance error caused by tire wear and tire pressure change is automatically adjusted for by the automatic distance correction function. This function, on the other hand, is for immediate adjustment, in cases such as driving with tire chain fitted on tires.

Fig 6: Screen Display - Speed Calibration

Courtesy of NISSAN MOTOR CO., U.S.A.

Error History

The self-diagnosis results are judged depending on whether any error occurs from when "Self-diagnosis" is selected until the self-diagnosis results are displayed.

However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned ON and then no error has occurred until the self-diagnosis start. Check the "Error Record" to detect any error that may have occurred before the self-diagnosis start because of this situation.

The error record displays the time and place of the most recent occurrence of that error. However, take note of the following points.

• If there is a malfunction with the GPS antenna circuit board in the AV control unit, the correct date and time of occurrence may not be able to be displayed.
• Place of the error occurrence is represented by the position of the current location mark at the time an error occurred. If current location mark has deviated from the correct position, then the place of the error occurrence cannot be located correctly.
• The frequency of occurrence is displayed in a count up manner. The actual count up method differs depending on the error item.

Count up method A

• The counter resets to 0 if an error occurs when ignition switch is turned ON. The counter increases by 1 if the condition is normal at a next ignition ON cycle.
• The counter upper limit is 39. Any counts exceeding 39 are ignored." The counter can be reset (no error record display) with the "Delete log" switch or CONSULT-III.

Count up method B

• The counter increases by 1 if an error occurs when ignition switch is ON. The counter will not decrease even if the condition is normal at the next ignition ON cycle.
• The counter upper limit is 50. Any counts exceeding 50 are ignored. "The counter can be reset (no error record display) with the "Delete log" switch or CONSULT-III".

Fig 7: Screen Display - Delete Log

Courtesy of NISSAN MOTOR CO., U.S.A.

Error item

Some error items may be displayed simultaneously according to the cause. If some error items are displayed simultaneously, the detection of the cause can be performed by the combination of display items

Vehicle CAN Diagnosis

• CAN communication status and error counter is displayed.
• The error counter displays "OK" if any malfunction was not detected in the past and displays "0" if a malfunction is detected. It increases by 1 if the condition is normal at the next ignition switch ON cycle. The upper limit of the counter is 39.
• The error counter is erased if "Reset" is pressed.
  Fig 8: Screen Display - Vehicle CAN Diagnosis

  Courtesy of NISSAN MOTOR CO., U.S.A.

AV COMM Diagnosis

• Displays the communication status between AV control unit (master unit) and each unit.
• The error counter displays "OK" if any malfunction was not detected in the past and displays "0" if a malfunction is detected. It increases by 1 if the condition is normal at the next ignition switch ON cycle. The upper limit of the counter is 39.
• The error counter is erased if "Reset" is pressed.
  Fig 9: Screen Display - AV COMM Diagnosis

  Courtesy of NISSAN MOTOR CO., U.S.A.

Hands-Free Phone

The hands-free phone reception volume adjustment and microphone and speaker test functions are also available.

Fig 10: Screen Display - Hands-Free Phone

Courtesy of NISSAN MOTOR CO., U.S.A.

Camera.

Refer to "ON BOARD DIAGNOSIS FUNCTION ".

XM

• Change Channel
  • Any necessary channels required to receive traffic information from the satellite radio system can be set.
• Change Application ID
  • Any application ID'-s required to receive traffic information from the satellite radio system can be set.
    Fig 11: Screen Display - Change Application ID

    Courtesy of NISSAN MOTOR CO., U.S.A.

Delete Unit Connection Log

Deletes any unit connection records and error records from the AV control unit memory. (Clear the records of the unit that has been removed.)

Fig 12: Screen Display - Delete Unit Connection Log

Courtesy of NISSAN MOTOR CO., U.S.A.

Initialize Settings

"User Data Initialization" and "Accessory Number Initialization" are possible.

Version Information

Version information of the AV control unit is displayed.

Fig 14: Screen Display - Version Information

Courtesy of NISSAN MOTOR CO., U.S.A.