LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2011 >> QX56 RWD >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window Control System >> DTC/Circuit Diagnosis >> Encoder >> Driver Side >> DRIVER SIDE : Diagnosis Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DRIVER SIDE : Diagnosis Procedure

  1. CHECK ENCODER SIGNAL
    1. Turn ignition switch ON.
    2. Check signal between power window main switch harness connector and ground with oscilloscope.
      SIGNAL REFERENCE

      Signal name (+) (-) Signal (Reference value)
      Power window main switch
      Connector Terminal
      Encoder signal 1 D5 13 Ground Refer to following signal
      Encoder signal 2 9
      Fig 1: Checking Signal Between Power Window Main Switch Harness Connector And Ground
      G06934392Courtesy of NISSAN MOTOR CO., U.S.A.

      Is the inspection result normal? 

      YES: Replace power window main switch. Refer to "REMOVAL AND INSTALLATION ".

      NO: GO TO 2.

  2. CHECK ENCORDER SIGNAL CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect power window main switch connector and front power window motor (driver side) connector.
    3. Check continuity between power window main switch harness connector and front power window motor (driver side) harness connector.
      CONTINUITY SPECIFICATION

      Power window main switch Front power window motor (driver side) Continuity
      Connector Terminal Connector Terminal
      D5 9 D7 6 Existed
      13 5
    4. Check continuity between power window main switch harness connector and ground.
      CONTINUITY SPECIFICATION

      Power window main switch Ground Continuity
      Connector Terminal
      D5 9 Not existed
      13

      Is the inspection result normal? 

      YES: GO TO 3.

      NO: Repair or replace harness.

  3. CHECK ENCORDER POWER SUPPLY
    1. Connect power window main switch connector.
    2. Turn ignition switch ON.
    3. Check voltage between front power window motor (driver side) harness connector and ground.
      VOLTAGE SPECIFICATION

      (+) (-) Voltage (V) (Approx.)
      Front power window motor (driver side)
      Connector Terminal
      D7 2 Ground 12

      Is the inspection result normal? 

      YES: GO TO  5.

      NO: GO TO 4.

  4. CHECK ENCORDER POWER SUPPLY CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect power window main switch connector.
    3. Check continuity between power window main switch harness connector and front power window motor (driver side) harness connector.
      CONTINUITY SPECIFICATION

      Power window main switch Front power window motor (driver side) Continuity
      Connector Terminal Connector Terminal
      D5 15 D7 2 Existed
    4. Check continuity between power window main switch harness connector and ground.
      CONTINUITY SPECIFICATION

      Power window main switch Ground Continuity
      Connector Terminal
      D5 15 Not existed

      Is the inspection result normal? 

      YES: Replace power window main switch. Refer to "REMOVAL AND INSTALLATION ".

      NO: Repair or replace harness.

  5. CHECK GROUND CIRCUIT 1
    1. Turn ignition switch OFF.
    2. Check continuity between front power window motor (driver side) harness connector and ground.
      CONTINUITY SPECIFICATION

      Front power window motor (driver side) Ground Continuity
      Connector Terminal
      D7 4 Existed

      Is the inspection result normal? 

      YES: Replace front power window motor (driver side). Refer to "REMOVAL AND INSTALLATION ".

      NO: GO TO 6.

  6. CHECK GROUND CIRCUIT 2
    1. Disconnect power window main switch connector.
    2. Check continuity between power window main switch harness connector and front power window motor (driver side) harness connector.
      CONTINUITY SPECIFICATION

      Power window main switch Front power window motor (driver side) Continuity
      Connector Terminal Connector Terminal
      D5 2 D7 4 Existed
    3. Check continuity between power window main switch harness connector and ground.
      CONTINUITY SPECIFICATION

      Power window main switch Ground Continuity
      Connector Terminal
      D5 2 Not existed

      Is the inspection result normal? 

      YES: Replace power window main switch. Refer to "REMOVAL AND INSTALLATION ".

      NO: Repair or replace harness.

scientia non olet · About LEMON Manuals