Values On The Diagnosis Tool

WARNING: This page is about a different car, the 2008 Infiniti EX35. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short-circuited.

REFERENCE VALUE TABLE

Monitor item	Display content	Data monitor
Monitor item	Display content	Condition	Reference value in normal operation
FR LH SENSOR	Wheel speed	Vehicle stopped	0 [km/h (MPH)]
FR LH SENSOR	Wheel speed	Vehicle running (Note 1)	Nearly matches the speedometer display (± 10% or less)
FR RH SENSOR	Wheel speed	Vehicle stopped	0 [km/h (MPH)]
FR RH SENSOR	Wheel speed	Vehicle running (Note 1)	Nearly matches the speedometer display (± 10% or less)
RR LH SENSOR	Wheel speed	Vehicle stopped	0 [km/h (MPH)]
RR LH SENSOR	Wheel speed	Vehicle running (Note 1)	Nearly matches the speedometer display (± 10% or less)
RR RH SENSOR	Wheel speed	Vehicle stopped	0 [km/h (MPH)]
RR RH SENSOR	Wheel speed	Vehicle running (Note 1)	Nearly matches the speedometer display (± 10% or less)
STOP LAMP SW	Stop lamp switch signal status	When brake pedal is depressed	On
STOP LAMP SW	Stop lamp switch signal status	When brake pedal is not depressed	Off
BATTERY VOLT	Battery voltage supplied to the ABS actuator and electric unit (control unit)	Ignition switch ON	10 - 16 V
GEAR	Gear position determined by TCM	1st gear 2nd gear 3rd gear 4th gear 5th gear	1 2 3 4 5
SLCT LVR POSI	A/T selector lever position	P position R position N position D position	P R N D
YAW RATE SEN	Yaw rate detected by yaw rate/side G sensor	Vehicle stopped	Approx. 0 d/s
		Vehicle turning right	Negative value
		Vehicle turning left	Positive value
ACCEL POS SIG	Throttle actuator opening/closing is displayed (linked with accelerator pedal)	Accelerator pedal not depressed (ignition switch is ON)	0%
ACCEL POS SIG		Depress accelerator pedal (ignition switch is ON)	0 - 100%
SIDE G-SENSOR	Transverse G detected by side G sensor	Vehicle stopped	Approx. 0 m/s²
		Vehicle turning right	Negative value
		Vehicle turning left	Positive value
STR ANGLE SIG	Steering angle detected by steering angle sensor	Driving straight	±2.5°
		Turn 90° to right	Approx. +90°
		Turn 90° to left	Approx. -90°
PRESS SENSOR	Brake fluid pressure detected by pressure sensor	With ignition switch turned ON and brake pedal released	Approx. 0 bar
PRESS SENSOR	Brake fluid pressure detected by pressure sensor	With ignition switch turned ON and brake pedal depressed	-40 to 300 bar
ENGINE RPM	With engine running	With engine stopped	0 rpm
ENGINE RPM	With engine running	Engine running	Almost in accordance with tachometer display
FLUID LEV SW	Brake fluid level switch signal status	When brake fluid level switch ON	On
FLUID LEV SW	Brake fluid level switch signal status	When brake fluid level switch OFF	Off
PARK BRAKE SW	Parking brake switch signal status	Parking brake switch is active	On
PARK BRAKE SW	Parking brake switch signal status	Parking brake switch is inactive	Off
LDP) APP SEN (Note 4)	Accelerator pedal position sensor status	Accelerator pedal is not depressed (Ignition switch ON)	0%
LDP) APP SEN (Note 4)	Accelerator pedal position sensor status	Depress accelerator pedal (Ignition switch ON)	0 - 100%
FR RH IN SOL	Operation status of each solenoid valve	Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III)	On
FR RH IN SOL	Operation status of each solenoid valve	When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON)	Off
FR RH OUT SOL	Operation status of each solenoid valve	Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III)	On
FR RH OUT SOL	Operation status of each solenoid valve	When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON)	Off
FR LH IN SOL	Operation status of each solenoid valve	Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III)	On
FR LH IN SOL	Operation status of each solenoid valve	When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON)	Off
FR LH OUT SOL	Operation status of each solenoid valve	Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III)	On
FR LH OUT SOL	Operation status of each solenoid valve	When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON)	Off
RR RH IN SOL	Operation status of each solenoid valve	Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III)	On
RR RH IN SOL	Operation status of each solenoid valve	When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON)	Off
RR RH OUT SOL	Operation status of each solenoid valve	Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III)	On
RR RH OUT SOL	Operation status of each solenoid valve	When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON)	Off
RR LH IN SOL	Operation status of each solenoid valve	Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III)	On
RR LH IN SOL	Operation status of each solenoid valve	When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON)	Off
RR LH OUT SOL	Operation status of each solenoid valve	Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III)	On
RR LH OUT SOL	Operation status of each solenoid valve	When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON)	Off
MOTOR RELAY	Motor and motor relay operation	When the motor relay and motor are operating	On
MOTOR RELAY	Motor and motor relay operation	When the motor relay and motor are not operating	Off
ACTUATOR RLY (Note 2)	Actuator relay operation	When the actuator relay is operating	On
ACTUATOR RLY (Note 2)	Actuator relay operation	When the actuator relay is not operating	Off
ABS WARN LAMP	ABS warning lamp (Note 3)	When ABS warning lamp is ON	On
ABS WARN LAMP	ABS warning lamp (Note 3)	When ABS warning lamp is OFF	Off
OFF LAMP	VDC OFF indicator lamp (Note 3)	When VDC OFF indicator lamp is ON	On
OFF LAMP	VDC OFF indicator lamp (Note 3)	When VDC OFF indicator lamp is OFF	Off
SLIP LAMP	SLIP indicator lamp (Note 3)	When SLIP indicator lamp is ON	On
SLIP LAMP	SLIP indicator lamp (Note 3)	When SLIP indicator lamp is OFF	Off
EBD SIGNAL	EBD operation	EBD is active	On
EBD SIGNAL	EBD operation	EBD is inactive	Off
ABS SIGNAL	ABS operation	ABS is active	On
ABS SIGNAL	ABS operation	ABS is inactive	Off
TCS SIGNAL	TCS operation	TCS is active	On
TCS SIGNAL	TCS operation	TCS is inactive	Off
VDC SIGNAL	VDC operation	VDC is active	On
VDC SIGNAL	VDC operation	VDC is inactive	Off
EBD FAIL SIG	EBD fail-safe signal	In EBD fail-safe	On
EBD FAIL SIG	EBD fail-safe signal	EBD is normal	Off
ABS FAIL SIG	ABS fail-safe signal	In ABS fail-safe	On
ABS FAIL SIG	ABS fail-safe signal	ABS is normal	Off
TCS FAIL SIG	TCS fail-safe signal	In TCS fail-safe	On
TCS FAIL SIG	TCS fail-safe signal	TCS is normal	Off
VDC FAIL SIG	VDC fail-safe signal	In VDC fail-safe	On
VDC FAIL SIG	VDC fail-safe signal	VDC is normal	Off
CRANKING SIG	Crank operation	Crank is active	On
CRANKING SIG	Crank operation	Crank is inactive	Off
USV [FL-RR] (Note 2)	VDC switch-over valve	When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III)	On
USV [FL-RR] (Note 2)	VDC switch-over valve	When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON)	Off
USV [FR-RL] (Note 2)	VDC switch-over valve	When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III)	On
USV [FR-RL] (Note 2)	VDC switch-over valve	When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON)	Off
HSV [FL-RR] (Note 2)	VDC switch-over valve	When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III)	On
HSV [FL-RR] (Note 2)	VDC switch-over valve	When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON)	Off
HSV [FR-RL] (Note 2)	VDC switch-over valve	When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-III)	On
HSV [FR-RL] (Note 2)	VDC switch-over valve	When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON)	Off
V/R OUTPUT (Note 2)	Solenoid valve relay activated	When the solenoid valve relay is active (When ignition switch OFF)	On
V/R OUTPUT (Note 2)	Solenoid valve relay activated	When the solenoid valve relay is not active (in the fail-safe mode)	Off
M/R OUTPUT	Actuator motor and motor relay activated	When the actuator motor and motor relay are active ("ACTIVE TEST" with CONSULT-III)	On
M/R OUTPUT	Actuator motor and motor relay activated	When the actuator motor and motor relay are inactive	Off
LDP) SHIFT POSITION (Note 4)	Shift position	Shift position is not received	Off
		Selector lever position	P/R/N/D
		When using manual mode	MM 1st - MM 6th
LDP) ICC MAIN SW (Note 4)	ICC main switch	ICC main switch is ON	On
LDP) ICC MAIN SW (Note 4)	ICC main switch	ICC main switch is OFF	Off
LDP) LDP ON SW (Note 4)	LDP ON switch	LDP ON switch is ON	On
LDP) LDP ON SW (Note 4)	LDP ON switch	LDP ON switch is OFF	Off
LDP) WIPER SIGNAL (Note 4)	Front wiper operation	Front wiper is OFF.	Stop
		Front wiper stops at fail-safe operation	PRTCT
		Front wiper INT is operating.	1low
		Front wiper LO is operating.	Low
		Front wiper HI is operating.	High
LDP) TURN SIGNAL (Note 4)	Turn signal operation	Turn signal is OFF.	Off
		Turn signal lamp RH is blinking.	LH
		Turn signal lamp LH is blinking.	RH
		Turn signal lamp LH and RH are blinking.	LH & RH
LDP) STOP LMP SW (Note 4)	Stop lamp switch signal status	When brake pedal is depressed	On
LDP) STOP LMP SW (Note 4)	Stop lamp switch signal status	When brake pedal is not depressed	Off
LDP) BRAKE SW (Note 4)	Brake switch signal status	When brake pedal is not depressed	On
LDP) BRAKE SW (Note 4)	Brake switch signal status	When brake pedal is depressed	Off
LDP) LDW SW (Note 4)	LDW switch condition	LDW switch is ON (LDW ON indicator is ON)	On
LDP) LDW SW (Note 4)	LDW switch condition	LDW switch is OFF (LDW ON indicator is OFF)	Off
NOTE: 1: Confirm tire pressure is normal. 2: A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is an operation for checking. 3: On and off timing for warning lamp and indicator lamp. ABS warning lamp: Refer to DESCRIPTION . Brake warning lamp: Refer to DESCRIPTION . VDC OFF indicator lamp: Refer to DESCRIPTION . SLIP indicator lamp: Refer to DESCRIPTION . Lane departure warning lamp: Refer to SYSTEM DESCRIPTION . 4: With LDP models.