Data Monitor

WARNING: This page is about a different car, the 2008 Infiniti EX35. However, it is still accessible from the selected car via links, so may be relevant.

DATA MONITOR TABLE

x: Applicable
Monitored Item [unit]	MAIN SIGNALS	Description
MAIN SW [On/Off]	x	Indicates [On/Off] status as judged from ICC steering switch signal (ECM transmits ICC steering switch signal through CAN communication).
SET/COAST SW [On/Off]	x	Indicates [On/Off] status as judged from ICC steering switch signal (ECM transmits ICC steering switch signal through CAN communication).
CANCEL SW [On/Off]	x	Indicates [On/Off] status as judged from ICC steering switch signal (ECM transmits ICC steering switch signal through CAN communication).
RESUME/ACC SW [On/Off]	x	Indicates [On/Off] status as judged from ICC steering switch signal (ECM transmits ICC steering switch signal through CAN communication).
DISTANCE SW [On/Off]	-	Indicates [On/Off] status as judged from ICC steering switch signal (ECM transmits ICC steering switch signal through CAN communication).
CRUISE OPE [On/Off]	x	Indicates whether controlling or not (ON means "controlling").
BRAKE SW [On/Off]	x	Indicates [On/Off] status as judged from ICC brake switch signal (ECM transmits ICC brake switch signal through CAN communication).
STOP LAMP SW [On/Off]	x	Indicates [On/Off] status as judged from stop lamp switch signal (ECM transmits stop lamp switch signal through CAN communication).
IDLE SW [On/Off]	-	Indicates [On/Off] status of idle switch read from ICC sensor integrated unit through CAN communication (ECM transmits On/Off status through CAN communication).
SET DISTANCE [Shor/Mid/Long]	x	Indicates set distance memorized in ICC sensor integrated unit.
CRUISE LAMP [On/Off]	x	Indicates [On/Off] status of MAIN switch indicator lamp output.
OWN VHCL [On/Off]	-	Indicates [On/Off] status of own vehicle indicator output.
VHCL AHEAD [On/Off]	-	Indicates [On/Off] status of vehicle ahead detection indicator output.
ICC WARNING [On/Off]	-	Indicates [On/Off] status of ICC system warning lamp output.
VHCL SPEED SE [km/h] or [mph]	x	Indicates vehicle speed calculated from ICC sensor integrated unit through CAN communication [ABS actuator and electric unit (control unit) transmits vehicle speed signal (wheel speed) through CAN communication].
SET VHCL SPD [km/h] or [mph]	x	Indicates set vehicle speed memorized in ICC sensor integrated unit.
BUZZER O/P [On/Off]	-	Indicates [On/Off] status of ICC warning chime output.
THRTL SENSOR [deg]	x	NOTE: This item is displayed, but cannot monitor.
ENGINE RPM [rpm]	-	Indicates engine speed read from ICC sensor integrated unit through CAN communication (ECM transmits engine speed through CAN communication).
WIPER SW [OFF/LOW/HIGH]	-	Indicates wiper [OFF/LOW/HIGH] status (BCM transmits front wiper request signal through CAN communication).
YAW RATE [deg/s]	-	NOTE: This item is displayed, but cannot monitor.
STP LMP DRIVE [On/Off]	x	Indicates [On/Off] status of ICC brake hold relay drive output.
D RANGE SW [On/Off]	-	Indicates [On/Off] status of "D" or "DS" or "M" positions read from ICC sensor integrated unit through CAN communication; ON when position "D" or "DS" or "M" (TCM transmits shift position indicator lamp signal through CAN communication).
NP RANGE SW [On/Off]	-	Indicates shift position indicator lamp signal read from ICC sensor integrated unit through CAN communication (TCM transmits shift position indicator lamp signal through CAN communication).
PWR SUP MONI [V]	x	Indicates IGN voltage input by ICC sensor integrated unit.
VHCL SPD AT [km/h] or [mph]	-	Indicates vehicle speed calculated from A/T vehicle speed sensor read from ICC sensor integrated unit through CAN communication (TCM transmits A/T vehicle speed sensor signal through CAN communication).
THRTL OPENING [%]	x	Indicates throttle position read from ICC sensor integrated unit through CAN communication (ECM transmits accelerator pedal position signal through CAN communication).
GEAR [1, 2, 3, 4, 5]	-	Indicates A/T gear position read from ICC sensor integrated unit through CAN communication (TCM transmits current gear position signal through CAN communication).
CLUTCH SW SIG [Off]	x	NOTE: This item is displayed, but cannot monitor.
NP SW SIG [On/Off]	x	Indicates [On/Off] status as judged from park/neutral position switch signal (ECM transmits park/neutral position switch signal through CAN communication).
MODE SIG [OFF, ICC, ASCD]	-	Indicates the active mode from ICC or ASCD [conventional (fixed speed) cruise control mode].
SET DISP IND [On/Off]	-	Indicates [On/Off] status of SET switch indicator output.
DISTANCE [m]	-	Indicates the distance from the vehicle ahead.
RELATIVE SPD [m/s]	-	Indicates the relative speed of the vehicle ahead.