LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2012 >> FX35 AWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - DTCS P0130 Through P0430 >> DTC P0340, P0345: CMP Sensor >> Diagnosis Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnosis Procedure

  1. CHECK STARTING SYSTEM

    Turn ignition switch to START position.

    Does the engine turn over? Does the starter motor operate? 

    YES: GO TO 2.

    NO: Check starting system. (Refer to "DIAGNOSIS AND REPAIR WORK FLOW ".)

  2. CHECK GROUND CONNECTION
    1. Turn ignition switch OFF.
    2. Check ground connection M95. Refer to Ground Inspection in "CIRCUIT INSPECTION ".

      Is the inspection result normal? 

      YES: GO TO 3.

      NO: Repair or replace ground connection.

  3. CHECK CAMSHAFT POSITION (CMP) SENSOR POWER SUPPLY CIRCUIT-I
    1. Disconnect CMP sensor harness connector.
    2. Turn ignition switch ON.
    3. Check the voltage between CMP sensor harness connector and ground.
      DTC CMP sensor Ground Voltage (V)
      Bank Connector Terminal
      P0340 1 F5 1 Ground Approx. 5
      P0345 2 F18 1

      Is the inspection result normal? 

      YES: GO TO  9.

      NO-1: P0340: Repair open circuit, short to ground or short to power in harness or connectors.

      NO-2: P0345: GO TO 4.

  4. CHECK CMP SENSOR POWER SUPPLY CIRCUIT-II
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between CMP sensor harness connector and ECM harness connector.
      CMP sensor ECM Continuity
      Bank Connector Terminal Connector Terminal
      2 F18 1 F102 64 Existed

      Is the inspection result normal? 

      YES: GO TO 5.

      NO: Repair or replace error-detected parts.

  5. CHECK CMP SENSOR POWER SUPPLY CIRCUIT-III

    Check harness for short to power and short to ground, between the following terminals:

    ECM Sensor
    Connector Terminal Name Connector Terminal
    F101 46 Crankshaft position (CKP) sensor F2 1
    F102 64 CMP sensor (bank 2) F18 1
    Exhaust valve timing (EVT) control position sensor (bank 2) F19 1
    Battery current sensor E21 1
    M107 103 Accelerator pedal position (APP) sensor E112 (Without ICC) 6
    E116 (With ICC) 3
    107 EVAP control system pressure sensor B252 3
    111 Refrigerant pressure sensor E77 3

    Is the inspection result normal? 

    YES: GO TO 6.

    NO: Repair short to ground or short to power in harness or connectors.

  6. CHECK COMPONENTS

    Check the Following:

  7. CHECK APP SENSOR

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO  15.

    NO: GO TO 8.

  8. REPLACE ACCELERATOR PEDAL ASSEMBLY

    Replace accelerator pedal assembly. Refer to "MODELS WITHOUT DISTANCE CONTROL ASSIST SYSTEM: REMOVAL AND INSTALLATION " (without distance control assist) or "MODELS WITH DISTANCE CONTROL ASSIST SYSTEM: REMOVAL AND INSTALLATION " (without distance control assist).

    : INSPECTION END

  9. CHECK CMP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between CMP sensor harness connector and ECM harness connector.
      DTC CMP sensor ECM Continuity
      Bank Connector Terminal Connector Terminal
      P0340 1 F5 2 F102 96 Existed
      P0345 2 F18 2 92
    4. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO  11.

      NO: GO TO 10.

  10. DETECT MALFUNCTIONING PART

    Check the Following:

    • Harness connectors F106, F107
    • Harness for open or short between CMP sensor and ECM

      : Repair open circuit, short to ground or short to power in harness or connectors.

  11. CHECK CMP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Check the continuity between CMP sensor harness connector and ECM harness connector.
      DTC CMP sensor ECM Continuity
      Bank Connector Terminal Connector Terminal
      P0340 1 F5 3 F102 59 Existed
      P0345 2 F18 3 63
    2. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO  13.

      NO: GO TO 12.

  12. DETECT MALFUNCTIONING PART

    Check the Following:

    • Harness connectors F106, F107
    • Harness for open or short between CMP sensor and ECM

      : Repair open circuit, short to ground or short to power in harness or connectors.

  13. CHECK CMP SENSOR

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO 14.

    NO: Replace malfunctioning camshaft position sensor. Refer to "EXPLODED VIEW ".

  14. CHECK CAMSHAFT (INT)

    Check the Following:

    • Accumulation of debris to the signal plate of camshaft rear end
    • Chipping signal plate of camshaft rear end

      Is the inspection result normal? 

      YES: GO TO 15.

      NO: Remove debris and clean the signal plate of camshaft rear end or replace camshaft. Refer to "REMOVAL AND INSTALLATION ".

      Fig 1: Inspecting Signal Plate Of Camshaft Rear End For Debris
      G04886473Courtesy of NISSAN NORTH AMERICA, INC.
  15. CHECK INTERMITTENT INCIDENT

    Perform "INTERMITTENT INCIDENT ".

    : INSPECTION END

scientia non olet · About LEMON Manuals