Active Test
WARNING: This page is about a different car, the 2011 Infiniti EX35. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
- Never perform "Active Test" while driving the vehicle.
- The "Active Test" cannot be performed when the ICC system warning lamp is illuminated.
- Shift the selector lever to "P" position, and then perform the test.
TEST ITEM DESCRIPTION
| Test item | Description |
|---|---|
| METER LAMP | The ICC system warning lamp, MAIN switch indicator, SET switch indicator and IBA OFF indicator lamp can be illuminated by ON/OFF operations as necessary. |
| DCA INDICATOR | The DCA system switch indicator can be illuminated by ON/OFF operations as necessary. |
| STOP LAMP | The ICC brake hold relay can be operated by ON/OFF operations as necessary, and the stop lamp can be illuminated. |
| BOOSTER SOL/V | The booster solenoid can be operated as necessary, and the brake can be operated. |
| ICC BUZZER | The ICC warning chime can sound by ON/OFF operations as necessary. |
| ACCELERATOR PEDAL ACTUATOR | The accelerator pedal actuator can be operated as necessary. |
METER LAMP
NOTE:
The test can be performed only when the engine is running.
TEST ITEM DESCRIPTION
| Test item | Operation | Description |
|
|---|---|---|---|
| METER LAMP | Off | Stops transmitting the signals below to end the test.
|
OFF |
| On | Transmits the following signals to the unified meter and A/C amp. via CAN communication.
|
ON |
DCA INDICATOR
NOTE:
The test can be performed only when the engine is running.
TEST ITEM DESCRIPTION
| Test item | Operation | Description | DCA system switch indicator |
|---|---|---|---|
| DCA INDICATOR | Off | Stops transmitting the DCA system switch indicator signal below to end the test. | OFF |
| On | Transmits the DCA system switch indicator signal to the unified meter and A/C amp. via CAN communication. | ON |
STOP LAMP
TEST ITEM DESCRIPTION
| Test item | Operation | Description | Stop lamp |
|---|---|---|---|
| STOP LAMP | Off | Stops transmitting the ICC brake hold relay drive signal below to end the test. | OFF |
| On | Transmits the ICC brake hold relay drive signal to the brake booster control unit via ITS communication. | ON |
BOOSTER SOL/V
NOTE:
The test can be performed only when the engine is running.
TEST ITEM DESCRIPTION
| Test item | Operation | Description | "PRESS SENS" value |
|---|---|---|---|
| BOOSTER SOL/V | MODE1 | Transmits the brake fluid pressure command signal to the brake booster control unit via ITS communication. | 10 bar |
| MODE2 | 20 bar | ||
| MODE3 | 30 bar | ||
| Test start | Starts the tests of "MODE1", "MODE2" and "MODE3". | - | |
| Reset | Stops transmitting the brake fluid pressure command signal below to end the test. | - | |
| End | Returns to the "SELECT TEST ITEM" screen. | - |
NOTE:
The test is finished in 10 seconds after starting.
ICC BUZZER
TEST ITEM DESCRIPTION
| Test item | Operation | Description | ICC warning chime operation sound |
|---|---|---|---|
| ICC BUZZER | MODE1 | Transmits the buzzer output signal to the brake booster control unit via ITS communication. | Intermittent beep sound |
| MODE2 | Continuous beep sound | ||
| MODE3 | Beep sound | ||
| Test start | Starts the tests of "MODE1", "MODE2" and "MODE3". | - | |
| Reset | Stops transmitting the buzzer output signal below to end the test. | - | |
| End | Returns to the "SELECT TEST ITEM" screen. | - |
ACCELERATOR PEDAL ACTUATOR
CAUTION:
- Shift the selector lever to "P" position, and then perform the test.
- Never depress the accelerator pedal excessively. (The engine speed may rise unexpectedly when finishing the test.)
NOTE:
- Depress the accelerator pedal to check when performing the test.
- The test can be performed only when the engine is running.
TEST ITEM DESCRIPTION
| Test item | Operation | Description | Accelerator pedal operation |
|---|---|---|---|
| ACCELERATOR PEDAL ACTUATOR | MODE 1 | Transmit the accelerator pedal feedback force control signal to the accelerator pedal actuator via ITS communication. | Constant with a force of 25 N for 8 seconds |
| MODE2 | Constant with a force of 15 N for 8 seconds | ||
| MODE3 | Change up to a force of 25 N for 8 seconds | ||
| MODE4 | Change up to a force of 15 N for 8 seconds | ||
| Test start | Starts the tests of "MODE1", "MODE2", "MODE3", and "MODE4". | - | |
| Reset | Stops transmitting the accelerator pedal feedback force control signal below to end the test. | - | |
| End | Returns to the "SELECT TEST ITEM" screen. | - |
NOTE:
The test is finished in 10 seconds after starting.