Diagnosis Procedure

1. CHECK GROUND CONNECTION
   1. Turn ignition switch OFF.
   2. Check ground connection M95. Refer to Ground Inspection in "CIRCUIT INSPECTION ".

      Is the inspection result normal? 

      YES: GO TO 2.

      NO: Repair or replace ground connection.

2. CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT
   1. Disconnect accelerator pedal position (APP) sensor harness connector.
   2. Turn ignition switch ON.
   3. Check the voltage between APP sensor harness connector and ground.

      APP sensor		Ground	Voltage (V)
      Connector	Terminal
      E112	5	Ground	Approx. 5

      Is the inspection result normal? 

      YES: GO TO  4.

      NO: GO TO 3.

3. DETECT MALFUNCTIONING PART

   Check the following.

   • Harness connectors M6, E106
   • Harness for open or short between ECM and accelerator pedal position sensor

     Repair open circuit or short to ground or short to power in harness or connectors.

4. CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-I
   1. Turn ignition switch ON.
   2. Check the voltage between APP sensor harness connector and ground.

      APP sensor		Ground	Voltage (V)
      Connector	Terminal
      E112	6	Ground	Approx. 5

      Is the inspection result normal? 

      YES: GO TO  9.

      NO: GO TO 5.

5. CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-II
   1. Turn ignition switch OFF.
   2. Disconnect ECM harness connector.
   3. Check the continuity between APP sensor harness connector and ECM harness connector.

      APP sensor		ECM		Continuity
      Connector	Terminal	Connector	Terminal
      E112	6	M107	103	Existed

      Is the inspection result normal? 

      YES: GO TO  7.

      NO: GO TO 6.

6. DETECT MALFUNCTIONING PART

   Check the following.

   • Harness connectors M6, E106
   • Harness for open or short between ECM and accelerator pedal position sensor

     Repair open circuit.

7. CHECK SENSOR POWER SUPPLY CIRCUIT

   Check harness for short to power and short to ground, between the following terminals.

   ECM		Sensor
   Connector	Terminal	Name	Connector	Terminal
   F101	46	CKP sensor (POS)	F2	1
   F102	64	CMP sensor (PHASE) (bank 2)	F18	1
   		EVT control position sensor (bank 2)	F63	1
   		Battery current sensor	E21	1
   M107	103	APP sensor	E112	6
   	107	EVAP control system pressure sensor	B252	3
   		Refrigerant pressure sensor	E77	3

   Is the inspection result normal? 

   YES: GO TO 8.

   NO: Repair short to ground or short to power in harness or connectors.

8. CHECK COMPONENTS

   Check the following.

   • Crankshaft position sensor (POS) (Refer to "COMPONENT INSPECTION ".)
   • Camshaft position sensor (PHASE) (bank 2) (Refer to "COMPONENT INSPECTION ".)
   • Exhaust valve timing control position sensor (bank 2) (Refer to "COMPONENT INSPECTION ".)
   • Battery current sensor (Refer to "COMPONENT INSPECTION ".)
   • EVAP control system pressure sensor (Refer to "COMPONENT INSPECTION ".)
   • Refrigerant pressure sensor (Refer to "DIAGNOSIS PROCEDURE ".)

     Is the inspection result normal? 

     YES: GO TO  15.

     NO: Replace malfunctioning component.

9. CHECK APP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
   1. Turn ignition switch OFF.
   2. Disconnect ECM harness connector.
   3. Check the continuity between APP sensor harness connector and ECM harness connector.

      APP sensor		ECM		Continuity
      Connector	Terminal	Connector	Terminal
      E112	4	M107	100	Existed
      	2		104

   4. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO  11.

      NO: GO TO 10.

10. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors M6, E106
    • Harness for open or short between ECM and accelerator pedal position sensor

      Repair open circuit or short to ground or short to power in harness or connectors.

11. CHECK APP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Check the continuity between APP sensor harness connector and ECM harness connector.

       APP sensor		ECM		Continuity
       Connector	Terminal	Connector	Terminal
       E112	3	M107	97	Existed
       	1		98

    2. Also check harness for short to ground and short to power.

       Is the inspection result normal? 

       YES: GO TO  13.

       NO: GO TO 12.

12. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors M6, E106
    • Harness for open or short between ECM and accelerator pedal position sensor

      Repair open circuit or short to ground or short to power in harness or connectors.

13. CHECK APP SENSOR

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO  15.

    NO: GO TO 14.

14. REPLACE ACCELERATOR PEDAL ASSEMBLY
    1. Replace accelerator pedal assembly. Refer to "REMOVAL AND INSTALLATION ".
    2. Go to "SPECIAL REPAIR REQUIREMENT ".

    INSPECTION END

15. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

INSPECTION END