| 4WD MODE [BOTNG/SWTNG/4L/4H/AUTO] |
|
X |
Control status of 4WD mode is displayed. |
| 2WD SW [On/Off] |
X |
|
4WD shift switch (2WD) is not equipped, but it is displayed. |
| AUTO SW [On/Off] |
X |
|
4WD shift switch signal (AUTO) is displayed. |
| 4H SW [On/Off] |
X |
|
4WD shift switch signal (4H) is displayed. |
| 4L SW [On/Off] |
X |
|
4WD shift switch signal (4L) is displayed. |
| T/M RANGE [D/N/R/P] |
X |
|
A/T shift selector position via CAN communication line is displayed. |
| N RANGESW [On/Off] |
X |
|
A/T shift selector position (N) via CAN communication line is displayed. |
| R RANGE SW [On/Off] |
X |
|
A/T shift selector position (R) via CAN communication line is displayed. |
| ING SW [On/Off] |
X |
|
Ignition switch status is displayed. |
| TCS OPER [On/Off] |
X |
|
TCS operation status via CAN communication line is displayed. |
| VDC OPER [On/Off] |
X |
|
VDC operation status via CAN communication line is displayed. |
| ABS OPER [On/Off] |
X |
|
ABS operation status via CAN communication line is displayed. |
| SAND MODE IND [On/Off] |
|
|
This indicator is not equipped, but it is displayed. |
| ROCK MODE IND [On/Off] |
|
|
This indicator is not equipped, but it is displayed. |
| SNOW MODE IND [On/Off] |
|
|
This indicator is not equipped, but it is displayed. |
| ONROAD MODE IND [On/Off] |
|
|
This indicator is not equipped, but it is displayed. |
| SAND MODE SW [On/Off] |
X |
|
This switch is not equipped, but it is displayed. |
| ROCK MODE SW [On/Off] |
X |
|
This switch is not equipped, but it is displayed. |
| SNOW MODE SW [On/Off] |
X |
|
This switch is not equipped, but it is displayed. |
| ONROAD MODE SW [On/Off] |
X |
|
This switch is not equipped, but it is displayed. |
| HI/LO POSI SEN 3 [On/Off] |
X |
|
Transfer Hi-Lo position sensor (3) status is displayed. |
| HI/LO POSI SEN 1 [On/Off] |
X |
|
Transfer Hi-Lo position sensor (1) status is displayed. |
| LOCK POSI SEN [OPEN/LOCK/BAT/UNLEAN/HI TEMP/ERROR/GND] |
X |
|
Transfer lock position sensor signal is displayed. |
| ATP IND [On/Off] |
|
|
Control status of ATP warning lamp is displayed. |
| 4WD FAILLAMP [On/Off] |
|
X |
Control status of ATP warning lamp is displayed. |
| 4WD MODE IND [4L/LOCK/AUTO] |
|
X |
Control status of 4WD mode indicator lamp is displayed. (LOCK means 4H of 4WD mode) |
| MOTOR DRIVE B [HI/LO/PWM] |
|
X |
Driving status of transfer motor is displayed. (Reverse side) |
| MOTOR DRIVE A [HI/LO/PWM] |
|
X |
Driving status of transfer motor is displayed. (Drive side) |
| FLUID TEMP SEN [V] |
X |
|
Temperature of transfer fluid is displayed. |
| MOTOR TEMP [V] |
X |
|
Temperature of transfer motor is displayed. |
| C/U POWER SUP [V] |
X |
|
Power supply voltage value of transfer control unit is displayed. |
| MOTOR POWER SUP [V] |
X |
|
Power supply voltage value of transfer motor unit is displayed. |
| ROTARY POSI SEN [%] |
X |
|
Transfer rotary position sensor signal is displayed. |
| THRTL POSI SEN [%] |
X |
X |
Throttle opening status via CAN communication line is displayed. |
| AT R SPEED [km/h] |
X |
|
Output shaft revolution speed via CAN communication line is displayed. |
| T/M GEAR [0 - 7] |
X |
|
Current transmission gear via CAN communication line is displayed. |
| COMPR VHCL SPEED [km/h] |
|
X |
Vehicle speed calculated by transfer control unit is displayed. |
| VHCL/S SEN-FR [km/h] |
X |
|
Wheel speed (front) average calculated by transfer control. |
| VHCL/S SEN-RR [km/h] |
X |
|
Wheel speed (rear) average calculated by transfer control. |
| ENG SPEED [RPM] |
X |
|
Engine status via CAN communication line is displayed. |
| INTERNL SPEED SEN [count] |
X |
|
Transfer internal speed sensor status is displayed. |
| TRANSFER TORQUE [Nm] |
|
X |
Commanded transfer communication torque is displayed. |
| UNIT PARAMETER [A1 - A9, B1 - B9, C1 - C9, D1 - D9, E1 - E9, F1 - F9, G1 - G9, H1 - H9, J1 - J9] |
|
|
Unit parameter of transfer recognized by transfer control unit is displayed. |