Common Specs & Procedures
Q60 (CONVERTIBLE) COMMON SPECS & PROCEDURES INDEX
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Torque | See Torque Specifications in text and applicable figures under REMOVAL AND INSTALLATION . | |||
| Axle Nut/Hub Nut | ||||
| Front Wheel Bearing Bolt | 65 Ft. lbs. (88.3 N.m) | |||
| Rear Axle Nut | 74-77 Ft. lbs. (100-105 N.m) | |||
| Battery | BATTERY | |||
| Brakes | ||||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | |||
| Disc Brakes | ||||
| Front | FRONT DISC BRAKE | |||
| Rear | REAR DISC BRAKE | |||
| Torque | ||||
| Front | See Torque Specifications in text and applicable figures under FRONT DISC BRAKE . | |||
| Rear | See Torque Specifications in text and applicable figures under REAR DISC BRAKE . | |||
| Charging | ||||
| Alternator | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Torque | See Torque Specifications in text and applicable figures under REMOVAL AND INSTALLATION . | |||
| Drive Belts | ||||
| Adjustment | Belt tension is adjusted by drive belt auto-tensioner. | |||
| Belt Routing | See Drive Belt Routing in appropriate figure under DRIVE BELT . | |||
| Engine Cooling | ||||
| General Service Specifications | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Radiator Cap Pressure | 18-22 psi (122.3-151.7 kPa, 1.2-1.5 kgf/cm2 ) | |||
| Thermostat R & I | WATER INLET AND THERMOSTAT ASSEMBLY | |||
| Water Pump R & I | WATER PUMP | |||
| Engine Mechanical | ||||
| Compression | Standard: 242 - 341 psi (1, 667-2, 354 kPa (17-24 kg/cm) Minimum: 178 psi (1, 226 kPa (12.5 kg/cm) Variance: 14 psi (98 kPa (1.0 kg/cm) |
|||
| Oil Pressure | ||||
| @ Idle | 14 psi (98 kPa (1.0.8 kgf/cm2 ) or more | |||
| @ 2000 RPM | 43 psi (294 kPa (3.0 kgf/cm2 ) on more | |||
| Overhaul | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Torque | See Torque Specifications in text and applicable figures under REMOVAL AND INSTALLATION . | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate (Drive Plate) Torque | 65 Ft. lbs. (88 N.m) | |||
| Fuel System | ||||
| Pressure | At Idling: Approximately 51 psi (350 kPa (3.57 kg/cm2 ) | |||
| Fuel Pressure Test Procedure | FUEL PRESSURE CHECK | |||
| Fuel Filter Location | Fuel filter is located on fuel pump unit in fuel tank. | |||
| Fuel Filter R & I | FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION . | |||
| Ignition Wires (Resistance) | Engine is equipped with Coil-On-Plug ignition. | |||
| Ignition Wires (Routing) | Engine is equipped with Coil-On-Plug ignition. | |||
| Spark Plugs | SPARK PLUG Tightening Torque: 14 Ft. lbs. (19.6 N.m) |
|||
| Starting | ||||
| Starter | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Torque | See Torque Specifications in text and applicable figures under REMOVAL AND INSTALLATION . | |||
| Wheel Alignment | ||||
| Adjustment Specifications | ||||
| Front | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Rear | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Torque | ||||
| Front | See Torque Specifications in text and applicable figures under REMOVAL AND INSTALLATION . | |||
| Rear | See Torque Specifications in text and applicable figures under REMOVAL AND INSTALLATION . | |||
| Wheel & Tire | ||||
| Lug Nut Torque | 80 Ft-lb (108 N.m) | |||
| How To Use Nissan/Infiniti Service Information | ||||
| Includes: Standard Bolt Torque Symbol Identification General Connector Info |
GENERAL INFORMATION (CONVERTIBLE) | |||