Confirmation Procedure

INSPECTION START
Is it necessary to erase permanent DTC?

YES

GO TO 7.

NO

GO TO 2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE-I
1. Turn ignition switch ON and wait at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

Refer to DTC Diagnosis Procedure .

NO

GO TO 4.
CHECK ENGINE COOLANT TEMPERATURE
With CONSULT
1. On CONSULT screen, select "ENGINE">>"Data Monitor">>"COOLAN TEMP/S".
2. Check "COOLAN TEMP/S" value.
"COOLAN TEMP/S" less than 60 deg.C (140 deg.F)?

YES

INSPECTION END

NO

GO TO 5.
PERFORM DTC CONFIRMATION PROCEDURE-II
With CONSULT
1. Cool engine down until "COOLAN TEMP/S" is less than 60 deg.C (140 deg.F).
2. Wait at least 10 seconds.
3. Check 1st trip DTC.
Is DTC P0181 detected?

YES

Refer to DTC Diagnosis Procedure .

NO

GO TO 6.

PERFORM COMPONENT FUNCTION CHECK (FOR MALFUNCTION B)

NOTE: Use the component function check to check the overall function of the FTT sensor circuit. During this check, a 1st trip DTC might not be confirmed.

Turn ignition switch OFF.
Disconnect "fuel level sensor unit and fuel pump" harness connector.
Remove fuel level sensor unit. Refer to FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY : Removal & Installation .

Check resistance between "fuel level sensor unit and fuel pump" terminals by heating with hot water as shown in the figure.

Courtesy of NISSAN NORTH AMERICA, INC.

Fuel level sensor unit and fuel pump		Condition		Resistance
+	-
Terminal
7	8	Temperature [ deg.C (deg.F)]	20 (68)	2.3 - 2.7 kOhm
			50 (122)	0.79 - 0.90 kOhm

Is the inspection result normal?

YES

To check malfunction symptom before repair: Refer to Inspection .

YES

Confirmation after repair: INSPECTION END

Refer to DTC Diagnosis Procedure .

PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TEST CONDITION:
- Before performing the following procedure, do not add fuel.
- Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
- Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
GO TO 8.
PERFORM DTC CONFIRMATION PROCEDURE B
1. Move the vehicle to a cool place.
  NOTE: Cool the vehicle in an environment of ambient air temperature between -10 deg.C (14 deg.F) and 35 deg.C (95 deg.F).
2. Turn ignition switch OFF and leave the vehicle for 12 hours.
  CAUTION: Never turn ignition switch ON during this procedure.
  
  NOTE: The vehicle must be cooled with the hood open.
3. Start engine and let it idle for 5 minutes or more.
  CAUTION: Never turn ignition switch OFF during idling.
4. Check 1st trip DTC.
Is DTC P0181 detected?

YES

Refer to DTC Diagnosis Procedure .

NO

To check malfunction symptom before repair: Refer to Inspection .

NO

Confirmation after repair: INSPECTION END