LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2021 >> Q60 Pure, AWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (DTCS) (4 Of 7) >> Engine (ECM) >> DTC P0461: Fuel Level Sensor >> Confirmation Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Confirmation Procedure

  1. CHECK DTC PRIORITY 

    If DTC P0461 is displayed with DTC UXXXX or P0607, first perform the confirmation procedure (trouble diagnosis) for DTC UXXXX or P0607.

    Is DTC UXXXX or P0607 detected?

    YES

    Perform diagnosis of applicable.

    NO

    GO TO 2.

  2. PRECONDITIONING 
    WARNING: When performing the following procedure, always observe the handling of the fuel. Refer to GENERAL PRECAUTION : Precautions .

    TESTING CONDITION:

    Before starting component function check, preparation of draining fuel and refilling fuel is required.

    Do you have CONSULT?

    YES

    GO TO 3.

    NO

    GO TO 4.

  3. PERFORM COMPONENT FUNCTION CHECK 
    NOTE: Use component function check to check the overall function of the fuel level sensor. During this check, a 1st trip DTC might not be confirmed.

    SYMBOL With CONSULT

    NOTE: Start from step 10, if it is possible to confirm that the fuel cannot be drained by 30 SYMBOL (7-7/8 US gal, 6-5/8 Imp gal) in advance.
    1. Prepare a fuel container and a spare hose.
    2. Release fuel pressure from fuel line, Refer to Work Procedure .
    3. Remove the fuel feed hose on the fuel level sensor unit.
    4. Connect a spare fuel hose where the fuel feed hose was removed.
    5. Turn ignition switch OFF and wait at least 10 seconds then turn ON.
    6. On CONSULT screen, select "ENGINE">>"Data Monitor">>"FUEL LEVEL SE".
    7. Check "FUEL LEVEL SE" output voltage and note it.
    8. On CONSULT screen, select "ENGINE">>"Active Test">>"FUEL PUMP RELAY".
    9. Touch "ON" and drain fuel approximately 30 SYMBOL (7-7/8 US gal, 6-5/8 Imp gal) and stop it.
    10. Check "FUEL LEVEL SE" output voltage and note it.
    11. Fill fuel into the fuel tank for 30 SYMBOL (7-7/8 US gal, 6-5/8 Imp gal).
    12. Check "FUEL LEVEL SE" output voltage and note it.
    13. Confirm whether the voltage changes more than 0.03V during step 7 to 10 and 10 to 12.

    Is the inspection result normal?

    YES

    To check malfunction symptom before repair: Refer to Inspection .

    YES

    Confirmation after repair: INSPECTION END

    NO

    Refer to DTC Diagnosis Procedure .

  4. PERFORM COMPONENT FUNCTION CHECK 

    SYMBOL Without CONSULT

    NOTE: Start from step 8, if it is possible to confirm that the fuel cannot be drained by 30 SYMBOL (7-7/8 US gal, 6-5/8 Imp gal) in advance.
    1. Prepare a fuel container and a spare hose.
    2. Release fuel pressure from fuel line. Refer to Work Procedure .
    3. Remove the fuel feed hose on the fuel level sensor unit.
    4. Connect a spare fuel hose where the fuel feed hose was removed.
    5. Turn ignition switch ON.
    6. Drain fuel by 30 SYMBOL (7-7/8 US gal, 6-5/8 Imp gal) from the fuel tank using proper equipment.
    7. Confirm that the fuel gauge indication varies.
    8. Fill fuel into the fuel tank for 30 SYMBOL (7-7/8 US gal, 6-5/8 Imp gal).
    9. Confirm that the fuel gauge indication varies.

    Is the inspection result normal?

    YES

    To check malfunction symptom before repair: Refer to Inspection .

    YES

    Confirmation after repair: INSPECTION END

    NO

    Refer to DTC Diagnosis Procedure .

scientia non olet · About LEMON Manuals