Lighting System: Pre-Check
WARNING: This page is about a different car, the 2005 Toyota Sienna. However, it is still accessible from the selected car via links, so may be relevant.
- USING HAND-HELD TESTER
- Hook up the hand-held tester to the DLC3.
- Monitor the ECU data by following the prompts on the tester screen.
HINT:
Hand-held tester has "Snapshot" function which records the monitored data.
Please refer to the hand-held tester operator's manual for further details.
- DTC CLEAR
- DTC and freeze frame data can be erased by operating the hand-held tester.
- DATA LIST
HINT:
By the DATA LIST displayed by the hand-held tester, you can read the value of the switch, sensor, actuator and so on without removing any part. Reading the DATA LIST as the first step in troubleshooting is one of the methods to shorten the labor time.
- Connect the hand-held tester to DLC3.
- Turn the ignition switch ON.
- According to the display on the tester, read the "DATA LIST".
BODY NO. 1:
DATA LIST (BODY NO. 1)Item Measurement Item/ Display (Range) Normal Condition Diagnostic Note ACC SW ACC SW signal/ ON or OFF ON: Ignition key is in ACC, ON or START position
OFF: Ignition key is in OFF position- IG SW IG SW signal/ ON or OFF ON: Ignition key is in ON or START position
OFF: Ignition key is in OFF or ACC position- PARKING BRAKE SW Parking brake SW signal/ON or OFF ON: Parking brake pedal is ON
OFF: Parking brake pedal is OFF- D DOR CTY SW Driver's door courtesy SW signal/ON or OFF ON: Driver's door is open
OFF: Driver's door is closed- P DOR CYT SW Passenger's door courtesy SW signal/ ON or OFF ON: Front passenger's door is open
OFF: Front passenger's door is closed- Rr DOR CTY SW Rear slide door courtesy SW signal/ON or OFF ON: Either right or left rear slide door is open
OFF: Both the right and left slide doors are closed- P LOCK POS SW Front passenger's door lock position SW signal/ON or OFF ON: Front passenger's door lock is in unlock position
OFF: Front passenger's door lock is in lock position- Rr. LOCK POS SW Rear slide door lock position SW signal/ON or OFF ON: Rear slide door lock is in unlock position
OFF: Rear slide door lock is in lock position- DIMMER SW Headlight dimmer SW signal/ON or OFF ON: Headlight dimmer switch is in HI or FLASH position
OFF: Headlight dimmer switch is in LO position- HIGH FLASHER SW Headlight dimmer SW signal/ON or OFF ON: Headlight dimmer switch is in FLASH position
OFF: Headlight dimmer switch is in except FLASH position- F FOG LIGHT SW Front fog light SW signal/ON or OFF ON: Front fog light switch is ON position
OFF: Front fog light switch is OFF position- AUTO LIGHT SW Auto light SW signal/ ON or OFF ON: Headlight dimmer switch is in AUTO position
OFF: Headlight dimmer switch is in except AUTO position- HEAD LIGHT SW Head light control SW signal/ON or OFF ON: Light control switch is in HEAD position
OFF: Light control switch is in except HEAD position- TAIL LIGHT SW Taillight SW signal/ ON or OFF ON: Light control switch is in TAIL or HEAD position
OFF: Light control switch is in OFF position- ILLUMINATE RATE Illuminate rate/ ON or OFF ON: Illuminate rate ON
OFF: Illuminate rate OFF- D LOCK POS SW Driver's door lock position SW signal/ ON or OFF ON: Door lock is in unlock position
OFF: Door lock is in lock position- LIGHTING TIME Lighting time/7.5 s, 15 s or 30 s Customized value can be displayed. - I/L ON/ACC OFF Light the I/L when ACC OFF/ON or OFF Customized sign can be displayed. - I/L ON/UNLOCK Interior light ON w/unlock/ON or OFF Customized sign can be displayed. - LIGHT CTRL TYPE Light control type/ CRNT or OLD Customized sign can be displayed. - LIGHT OFF DELAY Light auto OFF delay/ OFF, 30 s, 60 s, 90 s Customized value can be displayed. - BACK DOOR:
DATA LIST (BACK DOOR)Item Measurement Item/ Display (Range) Normal Condition Diagnostic Note COURTESY SW Back door courtesy SW signal/ ON or OFF ON: Back door is open
OFF: Back door is closed- - ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand-held tester allows the relay, VSV, actuator and so on to operate without removing any part. Performing the ACTIVE TEST as the first step of troubleshooting is one of the methods to shorten the labor time. The DATA LIST can be displayed during the ACTIVE TEST.
- Connect the hand-held tester to DLC3.
- Turn the ignition switch ON.
- According to the display on the tester, perform the "ACTIVE TEST".
BODY NO. 1:
ACTIVE TEST (BODY NO. 1)Item Test Details Diagnostic Note HAZARD Turn Hazard light flasher relay ON/OFF - F FOG LIGHT RLY Turn Front fog light relay ON/OFF - HEAD LIGHT Turn Headlight relay ON/OFF - HEAD LIGHT (HI) Turn Headlight dimmer relay (Headlight dimmer switch HI position) ON/OFF - TAIL LIGHT Turn Tail light relay ON/OFF - DRL RELAY (Test Details) Turn daytime running light relay ON/OFF (Vehicle Condition) Ignition SW is ON, engine is stopped and light control SW is in OFF position. - DIMMER SIG Turn Dimmer relay ON/OFF - ILLUMI OUTPUT (Test Details) Turn Interior light and Key illumination ON/OFF (Vehicle Condition) Interior light SW is in Door position and all doors are closed - - ILLUMINATED ENTRY SYSTEM OPERATION CHECK
- The illuminated entry system is explained below:
- Turn the ignition switch OFF, close all the doors, and set them in the lock condition.
- Unlock any door and open any other doors and check that the room light comes on. Close the door and check that the room light goes off in about 15 seconds.
- Turn the ignition switch ON and open and close any other of the doors. Check that the room light immediately goes off.
- Turn the ignition switch OFF.
- Open and close any of the door to turn the room light on. Before the room light goes off in about 15 seconds, turn the ignition switch ON. Check that the room light goes off immediately.
- Turn the ignition switch OFF.
- Open and close any of the doors to turn the room light come on. Before the light goes off in about 15 seconds, lock all the door. Check that the light goes off immediately.
- The illuminated entry system is explained below:
- LAMP AUTO CUT OPERATION CHECK
- Turn the ignition switch ON, and switch headlight into TAIL or HEAD position.
- Turn the ignition switch OFF and open the driver door, and check that the headlight goes off in about 30 seconds.
- Turn the ignition switch ON, and switch headlight into TAIL or HEAD position.
- Turn the ignition switch OFF and open the driver door. Before the headlight goes off in about 30 seconds, lock all the door. Check that the headlight goes off immediately.
- BATTERY SAVER OPERATION CHECK
- Remove the ignition key and close all the doors.
- Open any door to light the room light, and leave it open. Check that the light goes off in about 20 minutes.
- After the room light goes off, close the driver door.
- Open any door to turn the room light on, and then open another door. Check that the room light goes off within 20 minutes, after opening the doors.
- Close all the doors. With the ignition key inserted, open any door to light the room light and then, remove the ignition key. Check that the room light goes off within 20 minutes.