Section 192 (Quarter Power Windows): Adjustment

WARNING: This page is about a different car, the 2002 Lexus SC 430. However, it is still accessible from the selected car via links, so may be relevant.

REMOVE REAR SEAT CUSHION ASSY
1. Pull up the front portion of the seat cushion assembly, then remove it.
  
  Fig 1: Removing Rear Seat Cushion Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NOTE: In the case, hold the base of the clip up to prevent the cushion frame from being distorted.
REMOVE REAR SEAT HEADREST PLATE COVER
1. Using a screwdriver, remove the rear seat headrest plate cover.
  NOTE: Tape the screwdriver tip before use.
2. Use the same manner described above to the other side.
Fig 2: Removing Rear Seat Headrest Plate Cover
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE WIND DEFLECTOR BOARD ASSY
1. Remove the 4 bolts and wind deflector board assembly.
REMOVE REAR SEAT HEADREST PLATE
1. Using a screwdriver, remove the rear seat headrest plate.
  NOTE: Tape the screwdriver tip before use.
2. Use the same manner described above to the other side.
Fig 3: Removing Rear Seat Headrest Plate
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE REAR SEAT HEADREST ASSY
1. Remove the 2 nuts and rear seat headrest assembly.
  
  Fig 4: Removing Rear Seat Headrest Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Use the same manner described above to the other side.
REMOVE REAR SEAT BACK ASSY
1. Remove the 2 nuts, 2 bolts and rear seat back assembly.
Fig 5: Removing Rear Seat Back Assembly
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE DOOR SCUFF PLATE ASSY RH
1. Using a screwdriver, remove the door scuff plate RH.
NOTE: Tape the screwdriver tip before use.

Fig 6: Removing Door Scuff Plate RH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE QUARTER TRIM PANEL ASSY FRONT RH
1. Using a screwdriver, release the 4 claws and remove the front seat outer belt garnish.
  NOTE: Tape the screwdriver tip before use.
  
  Fig 7: Removing Front Seat Outer Belt Garnish
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Remove the 6 screws and clip.
3. Disengage the 4 clips, then remove the quarter trim panel RH.
Fig 8: Removing Quarter Trim Panel RH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
ADJUST QUARTER WINDOW ASSY RH
1. Adjust the upper part of the glass inward/outward.
  1. Loosen the 2 bolts on the quarter window assy.
  2. Using a hexagon wrench, turn the bolt for adjustment.
  Fig 9: Adjusting Upper Part Of Glass Inward/Outward
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Adjust the lower part of the glass inward/outward.
  1. Loosen the 2 bolts on the quarter window assy.
  2. Insert the shim to adjust the glass position (inside outside).
  Fig 10: Using Shims To Adjust Lower Part Of Glass Inward/Outward
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. When the window is fully closed, adjustment the vertical position of the glass.
  1. Loosen the 3 bolts on the glass for adjustment.
    Vertical position: +/-3 mm (+/- 0.12 in.)
  2. Only when the adjustment is not sufficient at (1), change the position of the door window upper stop for further adjustment.
Fig 11: Adjusting Vertical Position Of Glass
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NOTE:
- When the glass raised, it should reach the 2 upper stops simultaneously.
- Manually close the quarter window assy (See MANUAL CLOSE OPERATION ).
Fig 12: Adjusting Dimension Of Quarter Window Assembly
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL QUARTER TRIM PANEL ASSY FRONT RH
INSTALL DOOR SCUFF PLATE ASSY RH
INSTALL REAR SEAT BACK ASSY (See OVERHAUL )
Torque:

Bolt: 18 N.m (184 kgf.cm, 13 ft.lbf)

Nut: 7.0 N.m (71 kgf.cm, 63 in.lbf)