Headlight Assembly: Installation

HINT:

• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.

Fig 1: Identifying Red Line Acceptable Range Of Beam Angle Gauge

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. INSTALL LIGHT CONTROL ECU 
   1. Attach the claw and install the light control ECU.
      Fig 2: Locating Light Control ECU

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   2. Install the 4 screws with the cover.
      Fig 3: Identifying Cover Screws

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   3. Install the headlight protector with the screw.
      Fig 4: Identifying Headlight Protector Screw

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. INSTALL FRONT SIDE MAKER LIGHT BULB SOCKET 
   1. Install the front side maker light bulb to the front side maker light socket.
3. INSTALL FRONT SIDE MAKER LIGHT BULB 
   1. Turn the front side maker light bulb socket and the front side maker light bulb in the direction indicated by the arrow and install as a unit.
      Fig 5: Turning Front Side Maker Light Bulb Socket

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. INSTALL CLEARANCE LIGHT BULB SOCKET 
   1. Install the clearance light bulb to the clearance light socket.
5. INSTALL CLEARANCE LIGHT BULB 
   1. Turn the clearance light bulb socket and the clearance light bulb in the direction indicated by the arrow and install as a unit.
      Fig 6: Turning Clearance Light Bulb Socket

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. INSTALL FRONT TURN SIGNAL LIGHT BULB SOCKET 
   1. Install the front turn signal light bulb to the front turn signal light socket.
7. INSTALL FRONT TURN SIGNAL LIGHT BULB 
   1. Turn the front turn signal light bulb socket and the front turn signal light bulb in the direction indicated by the arrow and install as a unit.
   Fig 7: Turning Front Turn Signal Light Bulb Socket

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. INSTALL NO. 2 HEADLIGHT BULB 
   1. Turn the headlight No. 2 bulb in the direction indicated by the arrow and install it.
   Fig 8: Turning Headlight No. 2 Bulb

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. INSTALL HIGH-INTENSITY DISCHARGE HEADLIGHT BULB 
   1. Turn the back cover in the direction indicated by the arrow and install it.
   Fig 9: Turning Back Cover

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. INSTALL NO. 1 HEADLIGHT BACK COVER 
    1. Turn the headlight back cover No. 1 in the direction indicated by the arrow and install it.
    Fig 10: Turning Headlight Back Cover No. 1

    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
11. INSTALL FRONT BUMPER SIDE SUPPORT 
    1. Install the 3 screws with the bumper side support.
    Fig 11: Identifying Bumper Side Support Screws

    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
12. INSTALL HEADLIGHT ASSEMBLY 
    1. Attach the claw and install the 3 bolts with the headlight.
    2. w/ headlight cleaner:

       Connect the hose.

       Fig 12: Identifying Headlight Bolts

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect the connector as shown in the illustration.
       Fig 13: Connecting Headlight Connector

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
13. INSTALL ENGINE ROOM SIDE COVER (See  INSPECTION PROCEDURE  ) 
14. INSTALL FRONT BUMPER COVER (See  INSTALLATION  ) 
15. INSTALL COOL AIR INTAKE DUCT SEAL (See  INSTALLATION  ) 
16. CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
17. PERFORM INITIALIZATION 

    Some systems need initialization when disconnecting the cable from the negative battery terminal.

    (See INITIALIZATION )

18. INSPECT SRS WARNING LIGHT 
19. VEHICLE PREPARATION FOR HEADLIGHT AIM ADJUSTMENT (See  ADJUSTMENT  ) 
20. HEADLIGHT AIMING ADJUSTMENT (LOW BEAM) (See  ADJUSTMENT  ) 
21. HEADLIGHT AIMING ADJUSTMENT (HIGH BEAM) (See  ADJUSTMENT  )