Inspection Procedure

1. When the master switch assembly's door control switch is operated, check that the locked doors unlock.

   Result 

   POWER DOOR LOCK OPERATION
   
   

   Result	Proceed to
   Door locks operate normally	OK
   Door locks do not operate normally	NG

NG: GO TO POWER DOOR LOCK CONTROL SYSTEM (See  POWER DOOR LOCK CONTROL SYSTEM   ) 

OK: GO TO NEXT STEP 

1. Using the intelligent tester or Techstream, read the Data List.
   1. Intelligent tester

      RL-Door (Rear door ECU LH) 

      INTELLIGENT TESTER - RL-DOOR (REAR DOOR ECU LH)
      
      

      Tester Display	Measurement Item/Display	Normal Condition	Diagnostic Note
      ENTRY SENSOR	Rear LH side door touch sensor / ON or OFF	ON: Rear LH side door sensor is touched OFF: Rear LH side door sensor is not touched	-

   2. Techstream

      Rear Left Door (Rear door ECU LH) 

      TECHSTREAM - REAR LEFT DOOR (REAR DOOR ECU LH)
      
      

      Tester Display	Measurement Item/Display	Normal Condition	Diagnostic Note
      Entry Sensor	Rear LH side door touch sensor / ON or OFF	ON: Rear LH side door sensor is touched OFF: Rear LH side door sensor is not touched	-

      OK: On tester screen, item changes between ON and OFF according to above chart. 

NG: Go to step   4 

OK: GO TO NEXT STEP 

1. Replace the rear door ECU LH with a new one or normally functioning one (see REAR DOOR ).
2. Check that the entry function operates normally.

   OK: Operates normally 

NG: REPLACE CERTIFICATION ECU 

OK: END (REAR DOOR ECU LH IS DEFECTIVE) 

Fig 1: Identifying O14 ECU Connector And d2 Oscillator Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the O14 ECU connector.
2. Disconnect the d2 oscillator connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR LH
   
   

   Tester Connection	Condition	Specified Condition
   O14-16 (SEL) - d2-4 (SEL)	Always	Below 1 Ω
   O14-16 (SEL) - Body ground	Always	10 kΩ or higher

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: GO TO NEXT STEP 

Fig 2: Identifying d2 Oscillator Connector And d1 Handle Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the d2 oscillator connector.
2. Disconnect the d1 handle connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE LH
   
   

   Tester Connection	Condition	Specified Condition
   d2-2 (SGT8)-d1-6 (SGT7)	Always	Below 1 Ω
   d2-2 (SGT8) - Body ground	Always	10 kΩ or higher

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: GO TO NEXT STEP 

1. Replace the door electrical key oscillator with a new one or normally functioning one (see REAR DOOR ).
2. Check that the entry function operates normally.

   OK: Operates normally 

NG: Go to step 7 

OK: END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE) 

1. Replace the rear door outside handle LH with a new one or normally functioning one (see REMOVAL  ).
2. Check that the entry function operates normally.

   OK: Operates normally 

NG: Go to step 8 

OK: END (REAR DOOR OUTSIDE HANDLE LH IS DEFECTIVE) 

1. Replace the rear door ECU LH with a new one or normally functioning one (see REAR DOOR ).
2. Check that the entry function operates normally.

   OK: Operates normally 

NG: REPLACE CERTIFICATION ECU 

OK: END (REAR DOOR ECU LH IS DEFECTIVE)