Installation [04/2013 - 10/2017]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2017 Lexus IS 350, 2017 Lexus IS 300, 2016 Lexus IS 350, 2016 Lexus IS 300, and 2015 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL HEATED OXYGEN SENSOR

HINT:

Perform "Inspection After Repair" after replacing a heated oxygen sensor.

Refer to INITIALIZATION [04/2013 - 10/2017]

For Bank 2 (for 2WD):

Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.

SST: 09224-00010

Without SST [Torque (N*m (kgf*cm, ft.*lbf))]

Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf)

With SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))]

Torque: 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTE:

If a heated oxygen sensor has been struck or dropped, replace it.

HINT:

This torque value is effective when SST is parallel to the torque wrench.
The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).
If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.
Refer to PRECAUTION [04/2013 - 08/2015] , or refer to PRECAUTION [08/2015 - 10/2016] , or refer to PRECAUTION [10/2016 - 10/2017]

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Length of SST 30 mm (1.18 in.)
*b	Length of Torque Wrench 260 mm (10.2 in.)

Connect the heated oxygen sensor grommet to the body.

For Bank 2 (for AWD with Front Floor Cover LH):

Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Length of SST 30 mm (1.18 in.)
*b	Length of Torque Wrench 260 mm (10.2 in.)

SST: 09224-00010

Without SST [Torque (N*m (kgf*cm, ft.*lbf))]

Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf)

With SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))]

Torque: 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTE:

If a heated oxygen sensor has been struck or dropped, replace it.

HINT:

This torque value is effective when SST is parallel to the torque wrench.
The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).
If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.
Refer to PRECAUTION [04/2013 - 08/2015] , or refer to PRECAUTION [08/2015 - 10/2016] , or refer to PRECAUTION [10/2016 - 10/2017]

Connect the 2 clamps to the body.
Connect the heated oxygen sensor grommet to the body.
Install the front floor cover LH with the 6 clips.

For Bank 2 (for AWD without Front Floor Cover LH):

Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Length of SST 30 mm (1.18 in.)
*b	Length of Torque Wrench 260 mm (10.2 in.)

SST: 09224-00010

Without SST [Torque (N*m (kgf*cm, ft.*lbf))]

Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf)

With SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))]

Torque: 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTE:

If a heated oxygen sensor has been struck or dropped, replace it.

HINT:

This torque value is effective when SST is parallel to the torque wrench.
The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).
If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.
Refer to PRECAUTION [04/2013 - 08/2015] , or refer to PRECAUTION [08/2015 - 10/2016] , or refer to PRECAUTION [10/2016 - 10/2017]

Connect the 3 clamps to the body.
Connect the heated oxygen sensor grommet to the body.

For Bank 1:

Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.

SST: 09224-00010

Without SST [Torque (N*m (kgf*cm, ft.*lbf))]

Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf)

With SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))]

Torque: 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTE:

If a heated oxygen sensor has been struck or dropped, replace it.

*a	Length of SST 30 mm (1.18 in.)
*b	Length of Torque Wrench 260 mm (10.2 in.)

HINT:

This torque value is effective when SST is parallel to the torque wrench.
The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).
If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.
Refer to PRECAUTION [04/2013 - 08/2015] , or refer to PRECAUTION [08/2015 - 10/2016] , or refer to PRECAUTION [10/2016 - 10/2017]

Connect the heated oxygen sensor grommet to the body.

CONNECT HEATED OXYGEN SENSOR CONNECTOR
1. For Bank 2:
  1. w/ Clamp:
    1. Connect the clamp.
  2. Connect the heated oxygen sensor connector.
  3. Install the floor carpet.
2. For Bank 1:
  1. w/ Clamp:
    1. Connect the clamp.
  2. Connect the heated oxygen sensor connector.
  3. Install the floor carpet.
INSTALL CONSOLE BOX ASSEMBLY
Refer to INSTALLATION [04/2013 - 10/2016] , or refer to INSTALLATION [10/2016 - 09/2020]
INSTALL FRONT SEAT ASSEMBLY LH (for AWD)
Refer to INSTALLATION [04/2013 - ]
INSPECT FOR EXHAUST GAS LEAK
Refer to PROCEDURE - Step 9 [04/2013 - 10/2016] , or refer to PROCEDURE - Step 9 [10/2016 - 10/2017]
PERFORM INITIALIZATION
1. Perform "Inspection After Repair" after replacing a heated oxygen sensor.
  Refer to INITIALIZATION [04/2013 - 10/2017]