Specifications Index
GALANT SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | |||
| Automatic | GENERAL DESCRIPTION | ||
| Manual | GENERAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 226 +/- 29 N.m (167 +/- 21 ft-lb) | ||
| Rear | NA | ||
| Battery | ON-VEHICLE SERVICE | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | GENERAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes (Parking Brakes) | |||
| Service Specifications | Refer to GENERAL SPECIFICATIONS . Also refer to SERVICE SPECIFICATIONS | ||
| Torque | Refer to FASTENER TIGHTENING SPECIFICATIONS (Basic Brake) or FASTENER TIGHTENING SPECIFICATIONS (Parking Brakes). | ||
| Charging | |||
| Generator | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | |||
| 2.4L | Refer to 8. DRIVE BELTS (FOR GENERATOR, POWER STEERING PUMP AND AIR CONDITIONING) (CHECK) | ||
| 3.8L | Refer to 8. DRIVE BELTS (FOR GENERATOR, POWER STEERING PUMP AND AIR CONDITIONING) (CHECK) | ||
| Belt Routing | Refer to 8. DRIVE BELTS (FOR GENERATOR, POWER STEERING PUMP AND AIR CONDITIONING) (CHECK) | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATION | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (14 - 18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | |||
| 2.4L | THERMOSTAT | ||
| 3.8L | THERMOSTAT | ||
| Water Pump R & I | |||
| 2.4L | REMOVAL AND INSTALLATION < 2.4L ENGINE > | ||
| 3.8L | REMOVAL AND INSTALLATION < 3.8L ENGINE > | ||
| Engine Mechanical | |||
| 2.4L | |||
| Compression | Standard value (at engine speed of 250 - 400 r/min): 1,560 kPa (226 psi). Minimum limit (at engine speed of 250 - 400 r/min): 1,130 kPa (164 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil Pressure | Standard value: At idle: 29 kPa (4.2 psi) or more. At 3,500 r/min: 294 - 686 kPa (43 - 100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.8L | |||
| Compression | Standard value (at engine speed of 200 r/min): 1,550 kPa (225 psi). Minimum limit (at engine speed of 200 r/min): 1,110 kPa (161 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil pressure | Standard value: At idle: 29 kPa (4.2 psi) or more. At 3,500 r/min: 294 - 686 kPa (43 - 100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 2.4L | 132 +/- 5 N.m (98 +/- 3 ft-lb) | ||
| 3.8L | 74 +/- 1 N.m (54 +/- 1 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | Standard value: Approximately 324 kPa (95.7 in. Hg) at curb idle. | ||
| Fuel Pressure Test Procedure | |||
| 2.4L | FUEL PRESSURE TEST | ||
| 3.8L | FUEL PRESSURE TEST | ||
| Fuel Filter Location | FUEL PUMP MODULE REPLACEMENT | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.4L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.8L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | NA | ||
| Ignition Wires (Routing) | |||
| 2.4L | See Ignition System Diagram - 2.4L Engine figure under < 2.4L ENGINE > . | ||
| 3.8L | See Ignition System Circuit Diagram (3.8L Engine) figure under < 3.8L ENGINE > . | ||
| Spark Plug | |||
| 2.4L | |||
| Type | NGK; LZFR6AI | ||
| Gap | Standard value: 0.7 - 0.8 mm (0.028 - 0.031 inch). Limit: 1.2 mm (0.047 inch) | ||
| Torque | 25 +/- 5 N.m (19 +/- 3 ft-lb) | ||
| 3.8L | |||
| Type | NGK; FR6EI, DENSO; K20PSR-B8 | ||
| Gap | Standard value: 0.7 - 0.8 mm (0.028 - 0.031 inch). Limit: 1.2 mm (0.047 inch) | ||
| Torque | 25 +/- 5 N.m (19 +/- 3 ft-lb) | ||
| Starting | |||
| Starter | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 73+/-7 ft. lbs. (98+/-10 N.m) | ||