Common Specs & Procedures
LANCER EVOLUTION COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | GENERAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | For cotter pin and nut design, refer to >> B << WASHER/FRONT DRIVESHAFT NUT INSTALLATION . For staked nut design, tighten nut to 225 ± 25 N.m (184 ± 18 ft. lb.). | ||
| Rear | Refer to >> A << WASHER/REAR DRIVESHAFT NUT INSTALLATION . | ||
| Battery | GENERAL INFORMATION | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | Refer to GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS . | ||
| Torque | Torque specifications are found in article text and within article figures. | ||
| Drum Brakes | |||
| Service Specifications | INSPECTION | ||
| Torque | Torque specifications are found in article text and within article figures. | ||
| Charging | |||
| Generator | Refer to GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS . | ||
| Torque | Torque specifications are found in article text and within article figures. | ||
| Drive Belts | |||
| Adjustment | Refer to 7. DRIVE BELT (FOR THE GENERATOR AND POWER STEERING OIL PUMP) (REPLACE) . | ||
| Drive Belt Routing | Refer to Drive Belt Routing Diagram figure under >> B << DRIVE BELT INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | Refer to SERVICE SPECIFICATIONS and COOLANT . | ||
| Radiator Cap Pressure | 93-123 kPa (14-18 psi) | ||
| Thermostat R & I | REMOVAL AND INSTALLATION | ||
| Water Pump R & I | REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| Compression | Compression pressure at (200 r/min): 1, 090 kPa (158 psi); Minimum 750 kPa (109 psi); Compression pressure difference of all cylinder 100 kPa (14 psi) | ||
| Oil Pressure | At Idle: 29 kPa (4.2 psi) or more; At 3, 500 r/min: 294-686 kPa (43-100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See LUBRICATION AND MAINTENANCE . From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | Refer to >> E << FLYWHEEL BOLT INSTALLATION . | ||
| Fuel System | |||
| Pressure Specification | With engine running at idle: Approximately 260 kPa (38 psi) at curb idle; With vacuum hose removed from the intake manifold and after the nipple is closed with a cap: 310-345 kPa (45-50 psi) at curb idle | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module. | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | ON-VEHICLE SERVICE | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| Type | NGK: DILKR8B6 | ||
| Gap | Standard: 0.5-0.6 mm (0.020-0.023 in.); Limit: 0.8 mm (0.031 in.) | ||
| Torque | 18 ± 2 N.m (13 ± 1 ft. lb.). | ||
| Starting | |||
| Starter | Refer to GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS . | ||
| Torque | Torque specifications are within article figure under REMOVAL AND INSTALLATION . | ||
| Wheel Alignment | |||
| Adjustment Specifications | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 98 ± 10 N.m (73 ± 7 ft. lb.) | ||