LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mitsubishi >> 2021 >> Outlander PHEV LE >> Repair and Diagnosis (Single Page) >> Hybrid/Electric Powertrain >> Electric Motor Systems >> Electric Motor Control Unit (EMCU) And Motor (Electric Motor Unit) >> Service Data Reference Table >> Monitor Item
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Monitor Item

In this monitor item, the helpful items are set in order to comprehend the EMCU control situation. However, the values vary widely according to the minor differences of the measurement condition, the environmental differences, vehicle aging, or other factors, and offering the precise normal value is difficult. Therefore, only the check conditions, the display range, and the numerical change shall be listed.

Item No. Scan tool (M.U.T.-IIISE) display Item explanation Inspection conditions Display range
2 PHEV-ECU run mode Displays the present MCU control mode (1 to 6).
  1. OFF
  2. Reset
  3. High voltage on
  4. Torque control
  5. High voltage off
  6. Charging control
  7. F-ROM writing
 The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on. Displays the present MCU control mode (1 to 7).
3 Ready condition (PHEV) Displays the ready condition sent by the PHEV-ECU. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • Operation ready: Yes
  • Operation not ready No
4 Condenser discharge request Displays the feedback of the condenser discharge request. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • During discharge: Yes
  • Discharge stop: No
5 MCU shutdown request Displays the shutdown request state. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • During shutdown: Yes
  • Normal: No
6 PHEV communication lost The PHEV-ECU communicates with the MCU or not. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • While the communications fails: Yes
  • Normal: No
7 MCU CAN fail Displays whether the MCU has
CAN fail.		 The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • During failure: Yes
  • Normal: No
15 Condenser voltage Displays the condenser voltage. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on. 0 - 1000 V
21 Condenser discharge Displays the condenser discharge command state. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • During discharge: Discharge
  • Discharge stop: Stop
22 Ready condition (MCU) Displays whether the MCU is ready for operation. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • Operation ready: Yes
  • Operation not ready No
23 IGCT voltage keep request Displays whether the MCU requests IGCT power supply retention. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • With request: Set
  • Without request: No
24 HW gate Displays the IGBT gate state. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • Gate ON: ON
  • Gate OFF: OFF
25 HW shutdown Displays the shutdown command state. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on.
  • During shutdown: ON
  • Normal: OFF
43 CPU operation time Displays the energized time to CPU. The selector lever is at the P or N position with the power supply mode of the electric motor switch turned on. 0 hour to 65, 534 hour
scientia non olet · About LEMON Manuals